Preparation of Ba2YCu3O7-δ Thin Films with Preferred Orientation through an Organometallic Route

Superconducting Ba₂YCu₃O_7-δ thin films were prepared through an organometallic route. Single-phase Ba₂YCu₃O_7-δ thin films with preferred orientation were successfully prepared on SrTiO₃ (100) single-crystal substrates at 800°C by a dip coating method using partially hydrolyzed Ba-Y-Cu organometallic solutions. Preferentially oriented Ba₂YCu₃-O_7-δ thin films were also prepared on MgO (100) substrates. By controlling the partial hydrolysis conditions, a coating solution for precursor thin films was kept accurately at the stoichiometric composition. The use of ozone gas during the pyrolysis of the precursor thin films was found to suppress the formation of BaCO₃. Ba₂YCu₃O_7-δ thin films with c -axis orientation perpendicular to a SrTiO₃ (100) substrate, which were heat-treated at 900°C for 15 min, exhibited a superconductivity transition with an onset of 90 K and an end of 75 K.     

Effects of calcining conditions of kaolinite on pore structures of mesoporous materials prepared by the selective leaching of calcined kaolinite

This paper describes the effects of calcining conditions of kaolinite on pore structures of the porous materials obtained from the selective leaching of calcined kaolinite using KOH solution. Mesoporous -Al₂O₃ was the predominant crystalline phase in the samples calcined in the temperature range between 950°C and 1050°C for 24 h. The mean specific surface area of these samples was approximately 250 m² · g^–1 and the mean total pore volume was approximately 0.8 ml · g^–1. The pore size distribution curves of these samples showed a sharp peak at around 2–3 nm pore radius. This peak was sharper for the sample calcined at 1000°C for 24 h. On the other hand, the pore sizes of the sample calcined at 1100°C for 24 h increased abruptly to 10–20 nm and this change corresponded to the formation of mullite in the sample. The pore sizes of the samples calcined at 1100°C varied with calcining time. The specific surface area and total pore volume decreased, the longer the calcining time of the samples, and this was correlated with an increase in the amount of mullite in the samples.     

APPLICATION OF THE UNIFIED STATISTICAL MATERIAL DATABASE FOR DESIGN AND LIFE／RISK ASSESSMENT OF HIGH TEMPERATURE COMPONENTS

Statistical manipulation of material data was conducted for probabilistic life assessment or risk-based design and maintenance for high temperature components of power plants. To obtain the statistical distribution of material properties, dominant parameters affecting material properties are introduced into normalization of statistical variables. Those parameters are hardness, chemical composition, characteristic microstructural features and so on. Creep and fatigue properties are expressed by normalized parameters and the unified statistical distributions are obtained. These probability distribution functions show good coincidence statistically with the field database of steam turbine components. It was concluded that the unified statistical baseline approach is useful for the risk management of components in power plants.     

Hydrogen concentration on mirror surfaces of neutron bottles

Concentrations and depth distributions of the surface hydrogen and the surface deuterium in vacuum evaporated nickel layers and beryllium plates have been investigated by the ERDA method. It is shown that if the evaporation vacuum pressure is kept better than 10⁻⁶ Torr, the hydrogen adsorption from the residual gas during the evaporation is negligible and the hydrogen from residual or atmospheric gases after the evaporation is the main source of the surface hydrogen. Commercial beryllium plates are found to have surface hydrogen of about 10¹⁶ atoms cm². Deuterium treated samples, either in D₂ gas or heavy water, do not show more than possibly a partial replacement of hydrogen. The influence of substrates is small if the thickness of the evaporated nickel layer is more than 2000 Å. The measurements are in good agreement with previously published results.     

Continuous synthesis of Zn2SiO4:Mn fine particles in supercritical water at temperatures of 400-500 °C and pressures of 30-35 MPa

Sub-micron sized Zn₂SiO₄:Mn²⁺ phosphors particles were continuously synthesized in supercritical water with a flow reactor. Colloidal silica or sodium silicate was used as the Si source. Zn and Mn sources were chosen from their nitrates, sulfates, and acetates. The syntheses were carried out at temperatures from 400 to 500 °C, at pressures from 30 to 35 MPa, at NaOH concentrations from 0.014 to 0.025 M, and for residence times from 0.025 to 0.18 s. Sodium silicate formed α- and β-Zn₂SiO₄:Mn²⁺ phases regardless of the Zn and Mn sources, while colloidal silica formed phases dependent on the type of Zn and Mn sources used in addition to the use of alkali. As the reaction temperature increased, the crystallinity of α-Zn₂SiO₄:Mn²⁺ phase increased and the Mn substitution into the Zn sites of the α-Zn₂SiO₄ phase decreased. Of the conditions studied, the most highly crystalline α-Zn₂SiO₄:Mn²⁺ was produced at a temperature of 400 °C, a pressure of 30 MPa, a NaOH concentration of 0.14 M, and a residence time of 0.13 s with Zn and Mn sulfates and colloidal silica as starting materials. The α-Zn₂SiO₄:Mn²⁺ fine particles synthesized were round in shape, had an average diameter of 268 nm, and exhibited a green-emission with a peak wavelength of 524 nm.     

Design of a 1-MW,CW coaxial gyrotron with two gaussian beam outputs

The design of a 170 GHz, 1 MW-CW gyrotron for electron cyclotron heating of nuclear fusion plasmas is presented. The designed gyrotron incorporates a coaxial cavity to reduce mode competition, and a coaxial electron gun to support the cavity inner conductor. A new mode converter splits the generated wave into two beams and radiates them in different directions. The radiated beams are transmitted to two output windows through two mirror systems, being transformed into Gaussian-like beams. A single-stage depressed collector improves the overall efficiency of the gyrotron and reduces the heat flux to the collector surface.     

Durable write-once optical disk memories for 800 nm using silverisland films

Durable write-once (WO) optical disk media have been demonstrated by using silver island films with a protection layer of fluorine-contained polymers. The reflectance of the silver island films is high at the wavelength of 800 nm and can be greatly lowered by laser irradiation, owing to the thermal deformation or the islands. Laser writing has been experimentally confirmed at almost the same line speed as that of compact discs (CDs). Therefore it is expected that a CD-compatible write-once optical disc can be realised     

An Approach to a Higher‐Power‐Density Power Supply for a 380‐V DC Distribution System

A methodology for realizing a higher‐power‐density DC‐DC converter has been proposed for a power unit installed in a 380‐V DC distribution system. The possibility of the converter design will be strengthened by using the series–parallel connection topology for isolated DC‐DC converters. A converter prototype with a power density of 10 W/cm³ has been fabricated, and the feasibility of the converter design has been confirmed experimentally. This result contributes to the realization of a highly efficient and highly space‐saving 380‐V DC distribution system. © 2013 Wiley Periodicals, Inc. Electr Eng Jpn, 186(3): 51–62, 2014; Published online in Wiley Online Library ( wileyonlinelibrary.com ). DOI 10.1002/eej.22494     

Thermal decomposition of cellulose/synthetic polymer blends containing grafted products. V. Cellulose/polystyrene blends

Homogeneous grafting of styrene onto cellulose was carried out in a dimethylacetamide/lithium chloride solvent system. The grafted products were added to cellulose/polystyrene (PS) blends as compatibilizers. The thermal decomposition behavior of the blends was investigated by thermogravimetry. The thermal stability of the blends decreased with an increase in grafted product content. The crystallinity of the blends decreased with grafted product content. The microphase‐separated structures of the blends became finer with grafted product content. The glass transition temperatures for cellulose and PS in the blends were lowered with grafted product content. Differences in thermal decomposition behavior of the blends were correlated with compatibility. Thermogravimetry was effective for compatibility estimation in cellulose/PS blends containing grafted products. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010