The microstructure of Cu films deposited by the self-ion assisted technique

The microstructures of Cu films deposited by the self-ion assisted, partially ionized beam (PIB) deposition technique under two different accelerating potentials, 0 KeV and 6 KeV, are compared. The 6 KeV film shows a bimodal (111) fiber and (100) fiber texture with an abundance of twin boundaries and a relatively large average grain size with a typical lognormal distribution. The 0 KeV film consists of small, mostly (111) oriented grains with islands of abnormally large (100) grains. The controlling factors for the abnormal growth of the (100) grains are discussed in relation to the observed microstructures, showing that all factors necessary for abnormal (100) growth are present in the films.     

干涉条纹图估测基线的方法研究

根据SAR干涉测量原理，提出了利用干涉相干条纹估测基线的方法，并以欧洲空间局资源卫星1号和2号携带的SAR系统在中国新疆伽师试验区获取的串接式（Tan-dem）干涉测量数据为数据源，对提出的方法进行了验证，结果表明，该方法能有效地估测基线，并弥补不能有效获取卫星轨道参数时，对基线进行估测的缺陷，该方法尤其适用于差分干涉测量的研究。     

Deformation behavior of HCP Ti-Al alloy single crystals

Single crystals of Ti-Al alloys containing 1.4, 2.9, 5, and 6.6 pct Al (by weight) were oriented for 〈a〉 slip on either basal or prism planes or loaded parallel along the c-axis to enforce a nonbasal deformation mode. Most of the tests were conducted in compression and at temperatures between 77 and 1000 K. Trace analysis of prepolished surfaces enabled identification of the twin or slip systems primarily responsible for deformation. Increasing the deformation temperature, Al content, or both, acted to inhibit secondary twin and slip systems, thereby increasing the tendency toward strain accommodation by a single slip system having the highest resolved stress. In the crystals oriented for basal slip, transitions from twinning to multiple slip and, finally, to basal slip occurred with increasing temperature in the lower-Al-content alloys, whereas for Ti-6.6 pct Al, only basal slip was observed at all temperatures tested. A comparison of the critically resolved shear stress (CRSS) values for basal and prism slip as a function of Al content shows that prism slip is favored at room temperature in pure Ti, but the stress to activate these two systems becomes essentially equal in the Ti-6.6 pct Al crystals over a wide range of temperatures. Compression tests on crystals oriented so that the load was applied parallel to the c-axis showed extensive twinning in lower Al concentrations and 〈c+a〉 slip at higher Al concentrations, with a mixture of 〈c+a〉 slip and twinning at intermediate compositions. A few tests also were conducted in tension, with the load applied parallel to the c-axis. In these cases, twinning was observed, and the resolved shear for plastic deformation by twinning was much lower that that for 〈c+a〉 slip observed in compression loading. This article is based on a presentation made in the symposium entitled “Defect Properties and Mechanical Behavior of HCP Metals and Alloys” at the TMS Annual Meeting, February 11–15, 2001, in New Orleans, Louisiana, under the auspices of the following ASM committees: Materials Science and Critical Technology Sector, Structural Materials Division, Electronic, Magnetic & Photonic Materials Division, Chemistry & Physics of Materials Committee, Joint Nuclear Materials Committee, and Titanium Committee.     

Constant thrust programming for a multistage rocket flown in vacuum with a given initial/final thrust-to-weight ratio in an arbitrary stage

The burn time and burnout velocity of a multistage rocket flown vertically in vacuum with constant thrust tangential to the flight path and a prescribed initial/final thrust-to-weight ratio in an arbitrary stage have been determined. The present paper also deals with optimal staging under given conditions of flight.     

Generalisations of Heyman's and Foulkes' theorems using dual formulation

Existing duality principles in structural optimisation are briefly reviewed and then they are extended to structures with segment-wise constant cross-sections. All theories are discussed in the particular context of optimal plastic beam design with symmetric convex specific cost functions and are confirmed by independent calculations on illustrative examples. It is shown that the optimal solution is always associated with a displacement field in which the mean absolute curvature value for each segment equals the subgradient of the specific cost function, with respect to the maximum absolute moment value for that segment. Moreover, the dual problem consists of the maximisation of the difference of two terms: the first one is the integral of the product of load and deflection (external work), and the second is the sum of products of segment lengths and the mean complementary cost values (taken with respect to the mean absolute curvature for that segment). Finally, some tentative proposals for a class of non-convex optimisation problems are presented. For special cases, the proposed general statements reduce to theorems by Heyman, Foulkes and Hemp.     

Measurement of the delayed-neutron yields in the fission of233U,236U,237Np,240Pu,and241Pu by neutrons from the spectrum of a fast reactor

Translated from Atomnaya Énergiya, Vol. 66, No. 2, pp. 100–103, February, 1989.     

The emerging landscape of bioinformatics software systems

Fusing computing and biology expertise, bioinformatics software provides a powerful tool for organizing and mining the vast amounts of data genetics researchers are accumulating. As life scientists and computational scientists interact to create useful bioinformatics software systems, several themes or lessons recur. We identify seven themes: the nature of biological data; data storage, analysis and retrieval; computational modeling and simulation; biologically meaningful information integration; data mining; image processing and visualization; and closing the loop