Investigation of nickel deposition onto section and central longitudinal surfaces of AA1370 aluminum electrical wire with and without a weak permanent magnetic field

In this work a special regard is given to the morphology of the nickel deposited layers, onto AA1370 aluminum section and central longitudinal surfaces, with and without a weak magnetic field oriented in parallel and perpendicular to the coated surface in modified Watt bath. The obtained results show the formation of honeycomb structure nickel deposits for samples treated with weak parallel oriented field under approximately 0.3 A/cm₂, and partial dendritic structure nickel deposit for samples treated with weak perpendicular oriented magnetic field, the perimeter deposits with and without magnetic field is different to the deposits in the remain surface. We attributed the defect of nickel deposits on the surfaces with and without magnetic field to the distribution of the intermetallics particles and we attributed the honeycomb structure to the escapement of hydrogen and oxygen.     

Structured estimation of tire forces and the ground slope using SM observers

In agricultural context, the principal cause of serious accidents for all-terrain vehicles(ATVs) is rollover. The most important parameters related to this risk is the ground slope. In this paper, we propose a structured observer to estimate the system states and the longitudinal tire forces using only wheel angular velocities measurement. The robust estimation is based on a second order sliding mode observer. This estimation is then used to build up a ground slope estimation. The algorithm is composed by two cascaded estimators. This structured estimation is then applied to the model of an agricultural vehicle G7(GregoireTM) integrated in the driving simulation environment SCANeRTM-Studio.     

Prediction of Tool Wear in the Turning Process Using the Spectral Center of Gravity

The recent increase in machining productivity is closely related to longer tool life and good surface quality. In the present study, an experimental technique is proposed to evaluate the performance of a cemented carbide inset during the machining of AISI D3 steel. The aim of this technique is to find a relationship between the vibratory state of the cutting tool and the corresponding wear during machining in order to detect the beginning of the transition period to excessive wear. A spectral indicator named spectral center of gravity, SCG, is proposed to highlight the three phases of tool wear using the spectra of the accelerations measured. Very promising results are obtained which can be used to underpin an industrial monitoring system capable of detecting the onset of transition to excessive wear and alerting the user of the end of the tool’s life. The purpose of this study is to review the vibration analysis techniques and to explore their contributions, advantages and drawbacks in monitoring of tool wear.     

Angle dependence and defect production in metal-on-metal cluster deposition on surfaces

We use molecular dynamics to analyze the dependence on the impact angle of the distribution of defects originated by the deposition of a Ag₁₉ cluster on Pd(1 0 0) at initial kinetic energies 0.1, 2, 20 and 95 eV. For increasing energy the cluster undergoes a transition from a multi-layered adsorbed structure to a two-dimensional one. Implantation of Ag atoms and promotion of Pd substrate atoms is common to all energies and angles and, for a given initial total kinetic energy, it increases with decreasing impact angle.     

Investigations on ZnxCd1−xO thin films obtained by spray pyrolysis

Zn_xCd_1−xO thin films were prepared on glass substrates by spray pyrolysis technique. The precursor solutions were obtained by varying the concentration of Zn(NO₃)₂·6H₂O and Cd(NO₃)₂·4H₂O in bi-distilled water. The structural properties have been studied using X-ray diffraction spectra. All the structures include the basic compounds, i.e. ZnO and CdO. The orientation and the crystalline phases of the deposited films were specified. With the addition of Zn to the precursor solution, we can observe the preferential orientation of the CdO in the [2 0 0] direction. The electrical measurements were performed using method of four contacts. Thin films transmittances, in the 1.5–4.3 eV range, for different compositions have been measured and the optical gaps have been determined. The variations are explained considering the gaps of the two pure films. The influence of increased Cd concentration in the films on the structural, electrical and optical properties is investigated in this study.     

Modeling and simulation of solar cells quantum well based on SiGe/Si

In recent years, the development of quantum well solar cells QWSCs (Quantum Well Solar Cells) has generated a great deal of interest. These configurations have shown good promise to optimize the low conversion efficiency of conventional solar cells because of the high rate of absorption losses present in them. In this work, we are interested in modeling and simulation of two different structures of solar cells, a simple solar cell based on silicon Si and a quantum well solar cell SiGe/Si. When a solar cell is compared to 80 quantum well layers of Si_0.8Ge_0.2with a pin solar cell based on Si. The short circuit current J_sc increases from 23.55 to 37.48 mA/cm² with a relative increase of 59.15% found. In addition, the limit of the absorption band of the lower energy photons extends from 1100 nm to 2000 nm.     

Superplastic deformation behavior of 7075 aluminum alloy

A study has been made to investigate the effect of a prior amount of warm rolling on the superplastic forming behavior of a standard grade 7075 aluminum alloy. The thermomechanical treatment process presented for grain refinement includes furnace cooling from the solution treatment temperature to the overaging temperature, warm rolling from 65–85% deformation, recrystallization, and artificial aging treatment. Increasing the amount of warm rolling beyond 80% deformation does not produce material with higher elongation to failure when the thermomechanical treatment process presented is used. The largest value of elongation to failure was 700%, which was obtained for a specimen having a grain size of 8 μm at a strain rate of 6×10⁻³S⁻¹. The fracture surface exhibits a granular appearance indicative of an intergranular fracture mode. Dislocation activities within grains were observed, indicating the occurrence of dislocation slip during grain boundary sliding.