Degradation of a textile azo dye by pulsed arc discharge to the surface of wastewater

The pulsed arc discharge to the surface of wastewater was applied to the degradation of a textile azo dye (Acid Red 27). A high-voltage electrode (discharging electrode) was vertically placed above the surface of the wastewater while the wastewater itself was grounded. The pulsed arc discharge occurred between the tip of the discharging electrode and the surface of the wastewater, producing various oxidative species. Oxygen was used as the working gas instead of air to prevent nitrogen oxides from forming. The effect of several parameters on the chromaticity and chemical oxygen demand (COD) removal was examined. The results obtained showed that the chromaticity of the wastewater was completely removed by this process and the COD also decreased significantly. It has been found that ozone formed in the gas phase mainly affects the removal of the dye. The contribution of other effects such as ultraviolet light emission and OH radical formation during the arc discharge to the degradation of the dye was found to be less than 15%. For the present reactor system, the optimum pH, pulse repetition rate and agitation speed were found to be 3.0, 110 Hz and 300 rpm, respectively.     

Micro-end-milling of single-crystal silicon

Ductile-regime machining of silicon using micro-end-mill is almost impossible because of the brittle properties of silicon, crystal orientation effects, edge radius of the cutter and the hardness of tool materials. Micro-end-milling can potentially be used to create desired three dimensional (3D) free form surface features using the ductile machining technology for single-crystal silicon. There is still a lack of fundamental understanding of micro-end-milling of single-crystal silicon using diamond-coated tool, specifically basic understanding of material removal mechanism, cutting forces and machined surface integrity in micro-scale machining of silicon. In this paper, further research to understand the chip formation mechanism was conducted. An analysis was performed to discover how the chips are removed during the milling process. Brittle and ductile cutting regimes corresponding to machined surfaces and chips are discussed. Experiments have shown that single-crystal silicon can be ductile machined using micro-end-milling process. Forces generated when micro-end-milling single-crystal silicon are used to determine the performance of the milling process. Experimental results show that the dependence of the cutting force on the uncut chip thickness can be well described by a polynomial function order n. As cutting regime becomes more brittle, the cutting force has more complex function.     

Hefestos: an intelligent system applied to ubiquitous accessibility

This article proposes Hefestos, an intelligent system applied to ubiquitous accessibility. This model uses ubiquitous computing concepts to manage accessibility resources for people with disabilities. Among the concepts employed, context awareness, user profiles and trails management can be highlighted. The paper proposes an ontology for accessibility and delineates scenarios of its application in everyday life of people with disabilities. Moreover, the implementation of a smart wheelchair prototype and its application in a practical experiment is described. Ten users with a range of disability degrees tried the system and filled out a survey based on the technology acceptance model. This experiment demonstrated the main functionalities and the acceptance of the system. The results showed 96 % of acceptance regarding perceived easy of use and 98 % in perceived usefulness. These results were encouraging and show the potential for implementing Hefestos in real life situations.     

Performance Comparisons Between Thumb-Based and Finger-Based Input on a Small Touch-Screen Under Realistic Variability

The potential benefits of thumb-based touch interaction have not been fully exploited due to its usability problems and performance deterioration. Despite the well-known problems, mobile phone users often prefer thumb-based input method in their daily context of use. Without understanding input performance under realistic variability, design solutions may not address the problems adequately. This research aims to evaluate performance of one-handed thumb-based input compared to cradled finger-based input for the large number of users and varying task conditions. By investigating performance under a range of user- and task-variability, common patterns can be identified to help infer realistic performance in context of use. For this experiment, 259 participants were recruited balanced on gender and age. They performed user testing of moving an icon on a mobile touch-screen. Overall, the one-handed thumb input showed a 30% reduction in throughput compared to the cradled finger-based input, with significant reduction in speed and accuracy. Reduced throughput is attributed to inaccuracy rather than speed. In addition, the partial effects of touch position, dragging direction, and target size were investigated and quantified. In conclusion, performance could maintain constant throughput only for the finger-based input of limited task conditions, when realistic variability was introduced. Also, high variance of throughput for the thumb-based input led to poor conformity to Fitts’s law. The findings have implications for design of thumb-based touch interface to offset performance reduction and characterizing performance measure for thumb-based input method.     

Measurement feedback control for a class of feedforward nonlinear systems

We propose a measurement feedback controller for a class of feedforward nonlinear systems under sensor noise. The sensor noise has unknown magnitude, frequency, and phase. Our proposed controller is coupled with a low‐pass filter in such a way that the sensor noise is attenuated. We show that the controlled system results in bounded states whose ultimate bounds are inversely proportional to the minimum frequency of the sensor noise. Our result is further generalized to work in a case where the sensor noise is only required to have a Fourier transform with finite energy. Moreover, if the sensor noise enters only at partial states, depending on the location of the sensor noise, the ultimate bounds of the particular states can be made arbitrarily small via the gain factor of the controller. Copyright © 2012 John Wiley & Sons, Ltd.     

An object-based middleware supporting efficient interoperability on a smart home network

This paper proposes a novel object-based home network middleware for supporting the interoperability among home devices and smart grid devices. This middleware provides various types of abstract objects for flexible representation of heterogeneous home devices, which are classified based on their characteristics. It is also flexible enough to allow addition of new protocols and message conversion between different protocols through an abstraction layer, which are not supported by existing home network middlewares so that various protocols can be supported. As a result, it can be utilized to provide the interoperability among a variety of devices from sensors to typical home appliances as well as smart grid devices such as a home electric generator and a battery, which adopt different protocols. In order to demonstrate that home devices and smart grid devices are interoperable through the proposed middleware, we implement applications based on the middleware on a target platform consisting of embedded boards, sensors and laptops for emulation purposes of a home network. According to our emulation, this middleware can provide efficient interoperability among home devices and smart grid devices for future energy efficient home.     

Publishers’ relationships on the web: An examination of how publishers’ websites are causing changes in relations in the book industry

This research, funded by the British National Bibliography Research Fund, examined how publishers’ websites are causing changes in relations in the book industry in order to gain further understanding of the implications of the impact of the Internet on the publishing chain. The paper is set within the context of the development of electronic commerce and how business to consumer commerce is now being overtaken by the activity in business to business trading. Publishers have followed the main business trends in using their websites to develop relationships directly with the consumer, but have been rather slower in developing their business to business activity through the Internet. This study investigated what changes were taking place as a result of current publisher activity on the Web and how these changes were affecting the traditional lines of communication in the book industry. An analysis of a range of consumer publishers’ websites was carried out to see what facilities they were offering both to the general public and to business partners within the industry. Questionnaires and interviews were then conducted to establish how publishers, booksellers and wholesalers were using publishers’ websites and whether these sites were beneficial to the industry as a whole. Facilities found on the websites were examined and analysed in order to determine their usefulness and how they might be developed to aid business to business commerce. Additionally, several issues relating to online sales, changes in sales patterns and changes in working methods were discussed. Although an amount of quantitative data is included in the report, many of the issues raised relied on the perceptions and opinions of practitioners in the book trade.