Use of laser scanning confocal microscopy for characterizing changes in film thickness and local surface morphology of UV-exposed polymer coatings

Laser scanning confocal microscopy (LSCM) has been used to characterize the changes in film thickness and local surface morphology of polymer coatings during the UV degradation process. With the noninvasive feature of LSCM, one can obtain thickness information directly and nondestructively at various exposure times without destroying the specimens or deriving the thickness values from IR measurement by assuming uniform film ablation. Two acrylic polymer coatings were chosen for the study, and the physical and chemical changes of the two systems at various exposure times were measured and analyzed. Those measurable physical changes caused by UV exposure include film ablation, formation of pits and other surface defects, and increases in surface roughness. It was found in both coatings that changes in measured film thickness by LSCM were not correlated linearly to the predicted thickness loss using the changes in the CH band obtained by the Fourier Transform Infrared (FTIR) spectroscopy measurements in the later degradation stages. This result suggested it was not a uniform film ablation process during the UV degradation. At later stages, where surface deformation became severe, surface roughness and profile information using LSCM were also proven to be useful for analyzing the surface degradation process Presented at the 81st Annual Meeting of the Federation of Societies for Coatings Technology, November 13–14, 2004 in Philadelphia, PA.     

Process conditions affect pigment quality and yield in extracts of purple sunflower hulls

Extract of purple sunflower hulls is a potential red food colorant; however, suitable process conditions must still be identified. Selected process variables were studied using bench-scale units to prepare, clarify, concentrate and spray dry extracts. Concentration by evaporation at 32°C and addition of maltodextrin to 15% (wt/dry wt) prior to drying largely eliminated pigment degradation during those steps. Relative to water extracts, extracts prepared with 5 to 15% ethanol in water generally yielded more pigment with similar levels of degradation and loss during subsequent processing. Use of 5% ethanol/2% citric acid reduced yield by about half relative to water, but gave a powder with a lower degradation index and wetting time. Percentage recovery of pigment during concentration and drying was not greatly affected by solvent type or extraction temperature.     

Peer-to-peer bichromatic reverse nearest neighbours in mobile ad-hoc networks

The increasing use of mobile communications has raised many issues of decision support and resource allocation. A crucial problem is how to solve queries of Reverse Nearest Neighbour (RNN). An RNN query returns all objects that consider the query object as their nearest neighbour. Existing methods mostly rely on a centralised base station. However, mobile P2P systems offer many benefits, including self-organisation, fault-tolerance and load-balancing. In this study, we propose and evaluate 3 distinct P2P algorithms focusing on bichromatic RNN queries, in which mobile query peers and static objects of interest are of two different categories, based on a time-out mechanism and a boundary polygon around the mobile query peers. The Brute-Force Search Algorithm provides a naive approach to exploit shared information among peers whereas two other Boundary Search Algorithms filter a number of peers involved in query processing. The algorithms are evaluated in the MiXiM simulation framework with both real and synthetic datasets. The results show the practical feasibility of the P2P approach for solving bichromatic RNN queries for mobile networks.     

Personalized identification of abdominal wall hernia meshes on computed tomography

An abdominal wall hernia is a protrusion of the intestine through an opening or area of weakness in the abdominal wall. Correct pre-operative identification of abdominal wall hernia meshes could help surgeons adjust the surgical plan to meet the expected difficulty and morbidity of operating through or removing the previous mesh. First, we present herein for the first time the application of image analysis for automated identification of hernia meshes. Second, we discuss the novel development of a new entropy-based image texture feature using geostatistics and indicator kriging. Third, we seek to enhance the hernia mesh identification by combining the new texture feature with the gray-level co-occurrence matrix feature of the image. The two features can characterize complementary information of anatomic details of the abdominal hernia wall and its mesh on computed tomography. Experimental results have demonstrated the effectiveness of the proposed study. The new computational tool has potential for personalized mesh identification which can assist surgeons in the diagnosis and repair of complex abdominal wall hernias.     

MET𝔸P: revisiting Privacy-Preserving Data Publishing using secure devices

The goal of Privacy-Preserving Data Publishing (PPDP) is to generate a sanitized (i.e. harmless) view of sensitive personal data (e.g. a health survey), to be released to some agencies or simply the public. However, traditional PPDP practices all make the assumption that the process is run on a trusted central server. In this article, we argue that the trust assumption on the central server is far too strong. We propose Met _??P, a generic fully distributed protocol, to execute various forms of PPDP algorithms on an asymmetric architecture composed of low power secure devices and a powerful but untrusted infrastructure. We show that this protocol is both correct and secure against honest-but-curious or malicious adversaries. Finally, we provide an experimental validation showing that this protocol can support PPDP processes scaling up to nation-wide surveys.     

Effect of nitrogen,phosphorus and soil and crop residues management practices on maize (Zea mays L.) yield in ultisol of eastern Cameroon

The shortening of fallow period in several areas in tropical Africa has reduced soil fertility and exposed soils to erosion and run-off. Fertilizer application and crop conservation practices are needeed to sustain high crop yield and to conserve the natural resource base for upland crop production in the continent. Field trials were carried out to evaluate the effect of fertilizer application and soil and crop residues management practices on yield of maize (Zea mays L.) planted on a Plinthudult soil at Bertoua, Eastern Cameroon. Maize yields increased significantly with nitrogen and phosphorus fertilizer application. Under the rainfall pattern prevailing in the area, the amount of nitrogen required for maximum yield was higher in the second season. On the other hand, the amount of phosphorus required for maximum yield appeared to decrease with time. The burning of crop residues and weeds prior to planting together with no-till practive gave higher yield of maize than other soil and crop residues management practices.     

Hepatic Δ9 and Δ6 desaturase activities during the recovery period following carbon tetrachloride poisoningdesaturase activities during the recovery period following carbon tetrachloride poisoning

The liver microsomal Δ⁹ and Δ⁶ desaturase activities have been studied in rats with carbon tetrachloride-induced hepatitis. Immediately after poisoning, significant decreases were observed for both types of desaturase activity. However, recovery kinetics were slower for the Δ⁶ desaturase than for the Δ⁹ desaturase. The activities of NADH-ferricyanide and NADH-cytochrome C reductases, proteins involved in the electron transfers associated with microsomal desaturation, were also measured. There was a fall in both activities after poisoning, but this decrease was less than that of the desaturase activities.     

Gasification kinetics of oil sands coke

Kinetics of steam gasification of delayed and fluid cokes derived from Athabasca bitumen have been studied in 6.35 cm diameter stirred and fixed bed reactors. Experiments were carried out at atmospheric pressure and at temperatures between 800°C and 930°C. The coke particle size ranged from 0.1 to 3.5 mm, and the steam partial pressure was varied from 15.2 to 60.6 kPa. Scanning electron microscopy, surface area analysis, and mercury porosimetry were employed to relate physical structure changes in the solids to experimental kinetic data. Several kinetic models for gasification were tested with the experimental gasification data. Rate expressions are presented for carbon conversion and for the release of sulphur.     

Relationship between chemical degradation and thickness loss of an amine-cured epoxy coating exposed to different UV environments

The relationship between chemical degradation and thickness loss of an unpigmented, non UV-stabilized, crosslinked amine-cured epoxy coating exposed to three UV conditions was investigated. Spin-coated samples having a thickness of approximately 7 μm on an Si substrate were prepared from a stochiometric mixture of a bisphenol A epoxy resin and a tetra-functional amine curing agent. Samples were exposed outdoors and to two accelerated laboratory UV environments. Chemical degradation and thickness loss were measured by transmission Fourier transform infrared spectroscopy (FTIRS) and laser scanning confocal microscopy (LSCM), respectively. In addition, surface roughness and morphological changes were measured by atomic forcemicrosocopy (AFM) and LSCM. Substantial chemical degradation, thickness loss, and morpholocal changes occurred in the exposed films, and the rate of chemical degradation was greater than that due to the thickness loss. This additional chemical loss was attributed to an inhomogeneous degradation process in which nanoscale localized depressions initiate at certain sites on the surface, which then enlarge and deepen with exposure time. The results of this study provide a better understanding of the degradation mechanism and should lead to the development of scientific-based models for predicting the service life of crosslinked amine-cured epoxy coatings. Presented at the 82nd Annual Meeting of the Federation of Societies for Coatings Technology, October 27–29, 2004, in Chicago, IL     

Crack Growth in Solid Oxide Fuel Cell Materials: From Discrete to Continuum Damage Modeling

This paper addresses the damage and fracture issues of glass and ceramic materials used in solid oxide fuel cells. Analyses of an internal crack and of an interface crack between dissimilar materials were conducted using a modified boundary layer modeling approach. In this approach, fracture is allowed to occur in a small process window situated at an initial crack tip. Elastic displacement crack-tip fields are prescribed as remote boundary conditions. Crack propagation was first modeled discretely. Next, a continuum damage mechanics (CDM) model for brittle materials was developed to capture damage and crack growth in the process window. In particular, the damage model was applied to a glass-ceramic material that had been developed in-house for sealing purposes. Discrete and continuum damage solutions were then compared. Finally, the CDM model was used to determine the crack propagation direction as a function of a mode mixity measure.