A 63-mW H.264/MPEG-4 audio/visual codec LSI with module-wise dynamic Voltage/frequency scaling

A single-chip H.264 and MPEG-4 audio-visual LSI for mobile applications including terrestrial digital broadcasting system (ISDB-T / DVB-H) with a module-wise, dynamic voltage/frequency scaling architecture is presented for the first time. This LSI can keep operating even during the voltage/frequency transition, so there is no performance overhead. It is realized through a dynamic deskewing system and an on-chip voltage regulator with slew rate control. By the combination with traditional low power techniques such as embedded DRAM and clock gating, it consumes only 63 mW in decoding QVGA H.264 video at 15 frames/sec and MPEG-4 AAC LC audio simultaneously.     

Intracellular recovery of gold by microbial reduction of AuCl4 ions using the anaerobic bacterium Shewanella algae

Microbial reduction and intracellular precipitation of gold was achieved at 25 °C and pH 7 by using the mesophilic anaerobic bacterium Shewanella algae with H₂ as the electron donor. The reductive precipitation of gold by S. algae was a fast process: 0.1–1 mol/m³ AuCl₄⁻ ions were completely reduced to insoluble gold within 30 min. The biogenic precipitates were crystalline gold nanoparticles of 10–20 nm present in the periplasmic space. The reducing power of S. algae at 3.2 × 10¹⁵ cells/m³ and 25 °C was comparable to that of aqueous citric acid solution (chemical reductant) at 20 mol/m³ and 50 °C. The intracellular recovery of gold is potentially attractive as an environmentally friendly alternative to conventional methods.     

Preparation of ferroelectric Ba(Ti/sub 0.85/Sn/sub 0.15/)O/sub 3/ thin films by metal-organic decomposition

Ferroelectric Ba(Ti/sub 0.85/Sn/sub 0.15/)O/sub 3/ (BTS/sub 15/) thin film is newly prepared on the Pt/Ti/SiO/sub 2//Si substrate by metal-organic decomposition. The firing condition is determined by thermogravimetric and differential thermal analysis. The BTS/sub 15/ thin film with a flat surface and uniform thickness is obtained by spin coating in N/sub 2/ atmosphere that avoids moisture. The BTS/sub 15/ film has a perovskite phase and a preferential [110] texture. It is also found that the crystalline structure is cubic at 24/spl deg/C with a lattice constant of 4.01 /spl Aring/, and a grain size of about 30 nm was estimated by Scherrer equation and SEM image. From P-E hysteresis loop at 20/spl deg/C, the polarization at E=0 and the electric field at P=0 are found to be 1.07 /spl mu/C/cm/sup 2/ and 24.0 kV/cm, respectively. It is observed that the dielectric constant decreases monotonously from about 830 to 630 with increasing temperature ranging from 20/spl deg/C to 50/spl deg/C. Finally, it is found that the BTS/sub 15/ thin film shows a sufficient ferroelectricity and is an attractive material for functional ferroelectric devices, such as thermal-type infrared sensors.     

Impact of compression,physical aging,and freezing rate on the crystallization characteristics of an amorphous sugar matrix

Amorphous matrices made up of sugar molecules, are frequently used in food and pharmaceutical industries. A drawback to their use is that they are susceptible to collapse, as a result of water uptake and an increase in temperature and subsequently crystallize. Herein, the crystallization characteristics of amorphous sugar (sucrose and α-lactose) preparations were analyzed, with the purpose of obtaining knowledge that could lead to the prediction of how long the amorphous state is retained under various conditions. The impact of compression, physical aging and freezing rate on the induction period (t_ind) for crystallization were examined. Freeze-dried sugar samples were compressed at 74 or 443 MPa (5 min) and then rehumidified at specified RHs. Some freeze-dried sucrose samples were physically aged, and alternatively freeze-drying was conducted under different conditions. The isothermal crystallization of the prepared samples at different temperatures (T), the glass transition and the crystallization temperature (T_cry) were measured, using differential scanning calorimetry. The compression markedly decreased the t_ind, while significantly lowered the hygroscopicity. Physical aging and slower-freezing also shortened the t_ind. The t_ind was found to be correlated exclusively with (T_cry–T), regardless of rehumidification, compression, sugar type, physical aging and freezing rate in the freeze-drying process.     

An intermittent control model of flexible human gait using a stable manifold of saddle-type unstable limit cycle dynamics

Stability of human gait is the ability to maintain upright posture during walking against external perturbations. It is a complex process determined by a number of cross-related factors, including gait trajectory, joint impedance and neural control strategies. Here, we consider a control strategy that can achieve stable steady-state periodic gait while maintaining joint flexibility with the lowest possible joint impedance. To this end, we carried out a simulation study of a heel-toe footed biped model with hip, knee and ankle joints and a heavy head-arms-trunk element, working in the sagittal plane. For simplicity, the model assumes a periodic desired joint angle trajectory and joint torques generated by a set of feed-forward and proportional-derivative feedback controllers, whereby the joint impedance is parametrized by the feedback gains. We could show that a desired steady-state gait accompanied by the desired joint angle trajectory can be established as a stable limit cycle (LC) for the feedback controller with an appropriate set of large feedback gains. Moreover, as the feedback gains are decreased for lowering the joint stiffness, stability of the LC is lost only in a few dimensions, while leaving the remaining large number of dimensions quite stable: this means that the LC becomes saddle-type, with a low-dimensional unstable manifold and a high-dimensional stable manifold. Remarkably, the unstable manifold remains of low dimensionality even when the feedback gains are decreased far below the instability point. We then developed an intermittent neural feedback controller that is activated only for short periods of time at an optimal phase of each gait stride. We characterized the robustness of this design by showing that it can better stabilize the unstable LC with small feedback gains, leading to a flexible gait, and in particular we demonstrated that such an intermittent controller performs better if it drives the state point to the stable manifold, rather than directly to the LC. The proposed intermittent control strategy might have a high affinity for the inverted pendulum analogy of biped gait, providing a dynamic view of how the step-to-step transition from one pendular stance to the next can be achieved stably in a robust manner by a well-timed neural intervention that exploits the stable modes embedded in the unstable dynamics.     

High‐temperature latent heat storage technology to utilize exergy of solar heat and industrial exhaust heat

Latent heat storage (LHS) using phase change materials is quite attractive for utilization of the exergy of solar energy and industrial exhaust heat because of its high‐heat storage capacity, heat storage and supply at constant temperature, and repeatable utilization without degradation. In this article, general LHS technology is outlined, and then recent advances in the uses of LHS for high‐temperature applications (over 100 °C) are discussed, with respect to each type of phase change material (e.g., sugar alcohol, molten salt, and alloy). The prospects of future LHS systems are discussed from a principle of exergy recuperation. In addition, the technologies to minimize exergy loss in the future LHS system are discussed on the basis of the thermodynamic analysis by ‘thermodynamic compass’. Copyright © 2016 John Wiley & Sons, Ltd.     

Compression molding and melt‐spinning of the blends of poly(lactic acid) and poly(butylene succinate‐co‐adipate)

Poly(lactic acid) (PLA) is a biobased polymer made from biomass having high mechanical properties for engineering materials applications. However, PLA has certain limited properties such as its brittleness and low heat distortion temperature. Thus, the aim of this study is to improve toughness of PLA by blending with poly(butylene succinate‐co‐adipate) (PBSA), the biodegradable polymer having high toughness. Polymer blends of PLA and PBSA were prepared using a twin screw extruder. The melt rheology and the thermal property of the blends were examined. Further the blends were fabricated into compression molded parts and melt‐spun fiber and were subjected to tensile and impact tests. When the PBSA content was low, PBSA phase was finely dispersed in the PLA matrix. On the other hand, when the PBSA content was high, this minor phase dispersed as a large droplet. Mechanical properties of the compression molded parts were affected by the dispersion state of PBSA minor component in PLA matrix. Impact strength of the compression molded parts was also improved by the addition of soft PBSA. The improvement was pronounced when the PBSA phase was finely dispersed in PLA matrix. However, the mechanical property of the blend fibers was affected by the postdrawing condition as well as the PBSA content. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41856.