High Pressure Conductivity and Photoconductivity of Polyveratrole

Summary Electropolymerization of o-(CH₃O)₂C₆H₄ (Veratrole) in dry acetonitrile/tetrabutylammonium tetrafluoroborate at platinum electrode, yields a green polymeric conducting solid. As the pressure is increased, the material becomes more conductive, but sharp changes towards lower conductivity occur at 4.2 and 6.2 metric tons pressure, probably due to phase transitions. The photoconductivity shows an exponential increase as temperature is increased, but it shows reversible changes at 200 K, 225 K and 250 K during slow warming, also attributable to phase transitions. Photoconductivity of Polyveratrole increases with the radiation frequency, being higher under blue light than under red of infrared radiation and there is a linear increase of photoconductivity with radiation density. Conductivity transients show that the conductivity increases exponentially with time to the saturation point within few minutes, and it also decreases exponentially when the light is turned off and the circuit is open. This behaviour can be explained by formation and encounter of electron and hole as current carriers. A preliminary study indicates a piezoelectric effect for the material. absorption spectroscopy allowed the measurements of the material band gap.     

Solution of Helmholtz equation by Trefftz method

The application of the Trefftz method for calculating wave forces on offshore structures is presented. Indirect and direct formulations using complete and non-singular systems of Trefftz functions for the Helmholtz equation are posed in this paper. An effective technique using different interpolation functions for the velocity potential and wave force are suggested to improve the computational accuracy of the wave force. The numerical examples show that the present method is highly efficient and accurate.     

Highly monomode W1 waveguide square lattice photonic crystal lasers

Lasing of W1 square lattice-based photonic crystal lasers on the substrate approach is analyzed. A second-order distributed feedback highly monomode behavior is observed. A comprehensive two-dimensional and three-dimensional finite-difference time-domain computation analysis shows that this characteristic arises from the lattice geometry. Single-mode lasers can be obtained using this geometry, opening the way to the realization of monomode laser arrays.     

Stimulation of negative magnetoresistance by an electric field and light in silicon doped with boron and manganese

It is experimentally ascertained that light stimulates the negative magnetoresistance observed in a high electric field in silicon doped with boron and manganese. The optimum conditions (the electric field, temperature, illumination, and resistivity of the material) for observation of the largest magnitude of negative magnetoresistance in (Si:B):Mn are determined. The dependence of the negative magnetoresistance on the concentration of compensating impurity is established.     

Potential of vibro-milling technique for preparation of electroceramic nanopowders

The potential of the vibro-milling technique as a simple method to obtain usable quantities of single-phase electroceramic powders with nanosized particles was examined. A detailed study considering the role of both milling time and firing condition on phase formation and particle size of the final product was performed. The calcination temperature for the formation of the desired phase was lower when longer milling times have been applied. More importantly, by employing an appropriate choice of the milling time and calcination condition, high purity electroceramic nanopowders have been successfully prepared with a simple solid-state reaction method.     

A light refractory concrete for thermal insulation

Compositions have been developed for nonshrinking vibrocast thermally insulating light refractory concretes with densities of 1.0, 1.3, 1.5, and 1.8 g/cm³ for temperatures of use up to 1400°C. The structure and properties have been examined for the concrete of density 1.3 g/cm³. __________ Translated from Novye Ogneupory, No. 4, pp. 29–32, April, 2008.     

Influence of the preparation conditions on the size and morphology of nanocrystalline lanthanum orthoferrite

Nanocrystalline LaFeO₃ is prepared by the dehydration of coprecipitated lanthanum and iron(III) hydroxides. It is shown that the behavior of the samples during heating and the size distribution of LaFeO₃ nanocrystals can be considerably different depending on the scheme used for coprecipitation of lanthanum and iron hydroxides; independently of the method employed for coprecipitation of the initial compounds, sintering of the samples at 950°C leads to the formation of lanthanum orthoferrite crystals up to 100 nm in size.     

Formation of the complex oxide NaNdTiO<Subscript>4</Subscript>

The processes of phase formation in the Na₂CO₃-TiO₂ and Na₂CO₃-TiO₂-Nd₂O₃ systems are investigated in the temperature range 600–900°C. The high-temperature solid-phase reactions underlying the process of formation of complex oxide NaNdTiO4 are studied. It is established that the synthesis of the NaNdTiO₄ compound occurs through the reaction of the intermediate product Na₈Ti₅O₁₄ with neodymium oxide in the temperature range 720–780°C. The optimum method is proposed for synthesizing NaNdTiO₄, which makes it possible to reduce the temperature of the synthesis, to avoid the formation of impurities, and to obtain the product in a finely dispersed state.     

Software for computing dusty air flows in ventilation systems

Programs are presented for calculating dusty air flow in ventilation systems, which have been derived from the method of singular integral equations. They allow one to construct flow lines and determine the velocity pattern for the air in a closed rectangular region with outlet, flow, and extraction holes; a study is made on the dust particle behavior in the aerodynamic field in which there may be a rotating cylinder or pumping cylinder; determinations are made of the concentration and grain-size composition of the dust in the extraction hole; one can construct flow lines and single-particle paths in multicoupled regions of potential flows containing any number of rotating cylinders and cylinder pumps. Translated from Novye Ogneupory, No. 5, pp. 53–58, May, 2008.