A case study of regional catchment water quality modelling to identify pollution control requirements.

There are four ecologically important river catchments that contain candidate Special Areas of Conservation (cSACs) under the Habitats Directive in the Lake District National Park located in the North of England. These are the rivers Ehen, Kent, Derwent and Eden. For each cSAC, there are defined ecological criteria that include water quality targets to protect the designated species. Stretches of the riverine cSACs in each catchment are failing to meet these and other water quality targets. The Environment Agency commissioned a study of each catchment to provide the underpinning scientific knowledge to allow it to deliver its statutory obligations under the Habitats Directive. SIMCAT river water quality models were produced and used to predict the water quality impacts resulting from a number of water quality planning scenarios aimed at achieving full compliance with the Habitats Directive and other national and EEC water quality targets. The results indicated that further controls on effluent discharges will allow the majority of targets to be met but other sources of pollution will also need to be controlled. The outcome of the study also recognised that water quality improvements alone will not necessarily produce the required improvement to the ecological interest features in each cSAC.     

Connecting the second exhaust-heat boiler to the operating first one under the conditions of flow circuits of combined-cycle plants with two gas-turbine units and one steam turbine

Problems arising with connecting the second exhaust-heat boiler to the first exhaust-heat boiler under load in the case of flow circuits of combined-cycle plants of type PGU-450 are considered. Similar problems exist for two-boiler single-turbine units of type PGU-325 and for two-boiler single-turbine units of traditional steampower plants with an output of 200–300 MW upon connection of the second furnace of a two-furnace boiler to the operating first furnace. Analysis of the temperature-induced stressed state and of the cyclic strength of thick-walled elements of the steam-water conduit of PGU-450 and of two-furnace boilers of two-boiler single-turbine units with an output of 200–300 MW (the check valve, the inlet header of the water economizer) is used for determining the steam temperature differences in the high-pressure conduits to the steam turbine and the order of connection of the second exhaust-heat boiler to the operating fist one. Modes of enabling a two-boiler single-turbine unit of a combined-cycle plant, which are most “rigid” from the standpoint of thermal strength, are determined. __________ Translated from élektricheskie Stantsii, No. 2, February 2006, pp. 11–17.     

Hydrogen degradation of steels in gas mains after long periods of operation

We study the degradation of the mechanical and corrosion properties of 17G1S steel in gas mains as a result of operation for 28–40 yr. We reveal the simultaneous decrease in its strength and hardness, on the one hand, and impact toughness and crack resistance, on the other hand. The indicated parameters prove to be most sensitive to the in-service degradation of the metal. The degradation of steel leads to the increase in the strain-hardening coefficient and the appearance of the yield plateau in the tensile stress-strain diagram and causes the appearance of sensitivity to hydrogen embrittlement increasing in the process of operation. We analyze the role of absorbed hydrogen affecting the mechanism of strain aging and responsible for the appearance of defects. It is shown that the polarization resistance can be used not only for monitoring of the corrosion state of gas pipelines but also for the prediction of changes in their mechanical properties in the process of operation. __________ Translated from Fizyko-Khimichna Mekhanika Materialiv, Vol. 43, No. 5, pp. 97–104, September–October, 2007.     

Structure and Certain Properties of Hot-Pressed Boron Carbide-Based Ceramic with Calcium-Silicon Additive

The influence which the composition of powder mixtures, the treatment conditions which the mixtures are subjected to, and the conditions under which the hot-pressed composite materials B₄C – (5-10 mass%) calcium-silicon are fabricated exert on the structure, nature of failure, and mechanical properties of these materials is investigated. Optimum properties are possessed by material containing 10 mass% of addition. It is shown that the structure, morphology, and dispersivity, as well as the nature of the distribution of the components that are added to the composite material (secondary phase) vary as the temperature of hot pressing changes. Maximal mechanical characteristics of the composite material (σ_bend = 560 MPa, K _1c = 4.7 MPa·m^1/2, HV = 37 GPa) are attained at hot-pressing temperatures in the range 2000-2100°C.     

Thermal storage efficiencies of two solar saltless water ponds

A comparative study between two types of solar ponds is presented. The first type has its free surface covered by a thin layer of transparent paraffin oil. The second type is covered by transparent glass floating devices. Each device disposes an air-vacuum chamber. The free water surface between these devices is covered by transparent paraffin oil also. The thermal storage efficiency of each pond is estimated during two time periods: between sunrise and sunset and from midnight to midnight. The calculated efficiency between sunrise and sunset corresponds to the average transmittance–absorptance product. This is estimated using linear regression and also a maximum likelihood identification technique. The behavior of the system was studied by solving numerically the heat transfer equations of the system. Also an ARMAX (AutoRegressivie Moving Average with eXogenous signal) model allowing the assessment of its performance was presented. This efficiency is larger for the first pond during the sunrise to sunset period and smaller when calculated from midnight to midnight. Thus, the first type of pond could be preferred for a use just after the sunset of the same day, while the second for use after one or more days of heat storage.     

Combined time and wavelength multiplexing technique of optical fiber grating sensor arrays using commercial OTDR equipment

The use of a commercial optical time domain reflectometry device for simultaneous wavelength and time domain multiplexing of fiber-optic Bragg grating sensors is proposed and demonstrated. The realization of such systems provides an inexpensive way of interrogating several hundreds of sensors in a single fiber. Strain resolution of 30 /spl mu/m/m over a strain measuring range of 0.5% was obtained.     

One-dimensional diffuser based on a thick layer of dichromated gelatin

A new diffuser capable of scattering light in one direction (one-dimensional diffuser) has been developed and experimentally tested. The diffuser is formed in a thick layer of dichromated gelatin. The scattering indicatrices of the diffuser measured in two mutually perpendicular directions are presented. It is demonstrated that the indicatrix width in one direction is significantly greater than that in the perpendicular direc-tion. However, no zero-order diffraction has been observed. The proposed one-dimensional diffuser exhibits close scattering indicatrices for reading at a wavelength of 0.44 and 0.63 μm.     

British female academics and comparative psychology: Attempts to establish a research niche in the early 20th century.

Why was there a preponderance of women engaged in laboratory-based studies of animal behavior in Britain in the early years of the 20th century? As a new experimental subject with recently neglected potential, animal psychology then represented an opportunity for women to make further inroads into academic science. Because the study of psychology before World War I offered negligible professional opportunities for the application of the subject, the intake of students was restricted. Perhaps this encouraged academic access to it by aspiring female scientists who felt that career prospects, uncertain and socially unexpected of them in any case, were worth chancing for greater long-term rewards. The academic circumstances and contributions of 3 British female pioneers in experimental comparative psychology are discussed. (PsycINFO Database Record (c) 2010 APA, all rights reserved)     

Grain refinement of Al-7Si alloys and the efficiency assessment by recognition of cooling curves

Under sand cup solidification condition, the influence of Ti, B concentration, and holding time on the grain size of a high-purity Al-7Si alloy has been systematically studied. It is found that the grain size decreases rapidly at lower Ti or B additions, and is almost constant at the higher concentrations. For Al-3B refined Al-7Si alloys, the grain size increases at the initial period of holding time, and then rapidly becomes independent of holding time; while for Al-7Si alloys refined with Al-5Ti-1B, the grain size increases with holding time throughout. To evaluate the refinement efficiency, a new method named “intelligent evaluating of melt quality by pattern recognition of thermal analysis cooling curves” has also been introduced in this article. The results show that comparing the cooling curve of the evaluated melt with those in a database to find the most similar one to it can precisely assess the grain refinement efficiency of the measured Al-7Si alloy. In addition, the influence of Ti, B addition levels, and pouring temperatures on some characteristic parameters of cooling curve has also been discussed.