Double-pass oblique-incidence interferometer for the inspection of nonoptical surfaces

Interferometric testing of the flatness or straightness of ground surfaces of metals, granite, ceramics, and glasses has always proved difficult because of the extremely low specular reflection from these optically rough surfaces. At oblique angles of incidence the specular reflection coefficient of nonoptical surfaces increases rapidly, typically from near 0.01 at 75 degrees up to, say, 0.50 at 85 degrees and near 1.00 at 90 degrees angle of incidence. By taking advantage of this enhanced reflection at oblique incidence and the brightness and spatial coherence of visible gas lasers, it becomes practical to use interferometric inspection of nonoptical surfaces. A novel double-pass oblique-incidence interferometer is described which enables testing of large pieces having a specular reflection as low as 1%.     

Analysing quadratic effects of formative constructs by means of variance-based structural equation modelling

Together with the development of information systems research, there has also been increased interest in non-linear relationships between focal constructs. This article presents six Partial Least Squares-based approaches for estimating formative constructs’ quadratic effects. In addition, these approaches’ performance is tested by means of a complex Monte Carlo experiment. The experiment reveals significant and substantial differences between the approaches. In general, the performance of the hybrid approach as suggested by Wold (1982) is most convincing in terms of point estimate accuracy, statistical power, and prediction accuracy. The two-stage approach suggested by Chin et al (1996) showed almost the same performance; differences between it and the hybrid approach – although statistically significant – were unsubstantial. Based on these results, the article provides guidelines for the analysis of non-linear effects by means of variance-based structural equation modelling.     

RBS analysis of front contacts for surface-barrier detectors

Surface-barrier detector structures based on Au, WTi and Au/WTi contacts on (111) n-Si were analysed. The metal layers were deposited by evaporation or sputtering to 40–100 nm thicknesses. The aim was to improve the thermal stability of the surface-barrier structures and retain the favourable detector properties of the Au/Si system. Contact structures which contain WTi layers have shown a much better thermal stability compared to the Au/Si system, but the properties of the detectors were poorer. The probable reasons are the reactivity of W and Ti with the thin oxide layer on the silicon surface and perhaps the higher energy of adatoms during sputter-deposition. Both effects can influence the degradation of the surface-barrier properties.     

Tumor-Localized Administration of α-GalCer to Recruit Invariant Natural Killer T Cells and Enhance Their Antitumor Activity against Solid Tumors

Invariant natural killer T (iNKT) cells have the capacity to mount potent anti-tumor reactivity and have therefore become a focus in the development of cell-based immunotherapy. iNKT cells attack tumor cells using multiple mechanisms with a high efficacy; however, their clinical application has been limited because of their low numbers in cancer patients and difficulties in infiltrating solid tumors. In this study, we aimed to overcome these critical limitations by using α-GalCer, a synthetic glycolipid ligand specifically activating iNKT cells, to recruit iNKT to solid tumors. By adoptively transferring human iNKT cells into tumor-bearing humanized NSG mice and administering a single dose of tumor-localized α-GalCer, we demonstrated the rapid recruitment of human iNKT cells into solid tumors in as little as one day and a significantly enhanced tumor killing ability. Using firefly luciferase-labeled iNKT cells, we monitored the tissue biodistribution and pharmacokinetics/pharmacodynamics (PK/PD) of human iNKT cells in tumor-bearing NSG mice. Collectively, these preclinical studies demonstrate the promise of an αGC-driven iNKT cell-based immunotherapy to target solid tumors with higher efficacy and precision.     

AlphaFold2: A Role for Disordered Protein/Region Prediction?

The development of AlphaFold2 marked a paradigm-shift in the structural biology community. Herein, we assess the ability of AlphaFold2 to predict disordered regions against traditional sequence-based disorder predictors. We find that AlphaFold2 performs well at discriminating disordered regions, but also note that the disorder predictor one constructs from an AlphaFold2 structure determines accuracy. In particular, a naïve, but non-trivial assumption that residues assigned to helices, strands, and H-bond stabilized turns are likely ordered and all other residues are disordered results in a dramatic overestimation in disorder; conversely, the predicted local distance difference test (pLDDT) provides an excellent measure of residue-wise disorder. Furthermore, by employing molecular dynamics (MD) simulations, we note an interesting relationship between the pLDDT and secondary structure, that may explain our observations and suggests a broader application of the pLDDT for characterizing the local dynamics of intrinsically disordered proteins and regions (IDPs/IDRs).     

Study of the adhesion of Staphylococcus aureus to coated glass substrates

The adhesion of Staphylococcus aureus was studied using a selection of laboratory-prepared and commercially available coated glass substrates using a simple methodology. Substrates were examined by scanning electron microscopy, atomic force microscopy and water droplet contact angles. It was found that microbial adhesion was independent of surface roughness, when this was of a lower magnitude than microbial size. It was also found that microbial adhesion was greater for hydrophilic surfaces than for hydrophobic ones, but that on a photoinduced superhydrophilic surface, microbes were more spread out—a potential benefit for more effective photocatalytic disinfection. It is suggested that hydrophobic and photoinduced superhydrophilic surface coatings both have potential as a means of reducing microbial fouling of surfaces.     

Performance Evaluation of a Novel Converged Architecture for Digital-Video Transmission Over Optical Wireless Channels

A robust channel coding architecture for multigigabit-per-second digital-video transmission over the optical wireless channel is introduced and evaluated. The proposed scheme combines low-density parity-check coding with channel interleaving to improve the transmission over turbulent temporally correlated optical wireless channels while satisfying real-time video delay constraints. Frame error rates of the presented code design are evaluated via simulation for intensity-modulation/direct-detection optical wireless links in both lognormal- and Rayleigh-fading channels. Results indicate that the performance of the proposed system is effective across a large range of atmospheric turbulence strengths and achieves significant temporal diversity in moderately long (10 ms) temporal correlation times while satisfying a 0.3-s real-time delay constraint. Moreover, the proposed design is shown to outperform the Reed-Solomon codes prevalent in the legacy fiber and wireless digital-television distribution systems.     

Inductively heated shape memory polymer for the magnetic actuation of medical devices

Presently, there is interest in making medical devices such as expandable stents and intravascular microactuators from shape memory polymer (SMP). One of the key challenges in realizing SMP medical devices is the implementation of a safe and effective method of thermally actuating various device geometries in vivo. A novel scheme of actuation by Curie-thermoregulated inductive heating is presented. Prototype medical devices made from SMP loaded with nickel zinc ferrite ferromagnetic particles were actuated in air by applying an alternating magnetic field to induce heating. Dynamic mechanical thermal analysis was performed on both the particle-loaded and neat SMP materials to assess the impact of the ferrite particles on the mechanical properties of the samples. Calorimetry was used to quantify the rate of heat generation as a function of particle size and volumetric loading of ferrite particles in the SMP. These tests demonstrated the feasibility of SMP actuation by inductive heating. Rapid and uniform heating was achieved in complex device geometries and particle loading up to 10% volume content did not interfere with the shape recovery of the SMP.     

Mobility degradation effects in CMOS differential pair transconductors

The influence of the mobility reduction factor on the dominant third-harmonic distortion and effective transconductance in CMOS differential pair transconductors is examined. Analytical expressions are developed which are suitable for hand calculation and generate realistic estimates for distortion and transconductance. The results produced have been tested against SPICE simulations over a wide range of parameter values and show excellent agreement. The analysis highlights the importance of mobility degradation and reveals that the linearity of the source-coupled differential pair is actually improved as the mobility reduction factor increases. This surprising finding suggests that where 0.15, for example, acceptably low distortion levels (<60 dB for V _i =1 V _pp ) should be achievable with the basic long-tailed pair and that complex linearization schemes may be unnecessary.This work is supported by a grant of the Science and Engineering Research Council.     

Time-dependent optical spectroscopy and imaging for biomedicalapplications

The application of optical spectroscopy and imaging in living tissue is complicated by multiple scattering of light. In spectroscopy, this scattering causes uncertainty in the pathlength traveled by photons in the tissue, while images suffer reduced resolution and contrast. Picosecond light sources and fast detectors have made it possible to address these problems by direct measurement of the photon time-of-flight. Diffusion models of light propagation can be used to relate the measured distribution of photon transit times to the scattering and absorption coefficients of the tissue. The advantages of absolute absorption measurement are demonstrated for two problems: determination of hemoglobin oxygenation in tissue and in vivo measurement of the uptake of an exogenous chromosphere such as photosensitizer. Optical imaging may also be improved by the elimination of multiply scattered photons or by selective detection of photons arriving from a given region of the tissue. The potential advantages of these techniques are discussed and illustrated with experimental data