Miniature heart cell force transducer system implemented in MEMS technology

A fully submersible force transducer system for use with isolated heart cells has been implemented using microelectromechanical systems (MEMS) technology. By using integrated circuit fabrication techniques to make mechanical as well as electrical components, the entire low-mass transducer is only a few cubic millimeters in size and is of higher fidelity (approximately 100 nN and 13.3 kHz in solution) than previously available. When chemically activated, demembranated single cells attached to the device contract and slightly deform a strain gauge whose signal is converted to an amplified electrical output. When integrated with a video microscope, the system is capable of optical determination of contractile protein striation periodicity and simultaneous measurement of heart cell forces in the 100-nN to 50-microN range. The average measured maximal force was Fmax = 5.77 +/- 2.38 microN. Normalizing for the cell's cross-sectional area, Fmax/area was 14.7 +/- 7.7 mN/mm2. Oscillatory stiffness data at frequencies up to 1 kHz has also been recorded from relaxed and contracted cells. This novel MEMS force transducer system permits higher fidelity measurements from cardiac myocytes than available from standard macro-sized transducers.     

Industry case studies in the use of immersive virtual assembly

In this paper, we report on two engineering case studies that have been conducted as part of a Virtual Assembly Technology Consortium. The objectives of the case studies were to determine if immersive virtual assembly capabilities allow industry assembly situations to be modelled and studied realistically, and to demonstrate the downstream value of the virtual assembly capabilities in areas such as ergonomics, assembly installation, process planning, installation, and serviceability. What is of special significance is that instead of modelling simplified problems or perceived representative situations, the case studies were constructed from actual assembly floor projects and situations encountered at industry member sites and with considerable participation from industry engineers and manufacturing shop floor personnel. Based on the success of the case studies, the consortium members inferred that virtual assembly methods are poised to move out of the realm of special projects and test scenarios to deployment in the actual design and manufacturing cycle. However, in order to be truly accepted in industry, there are still issues to be addressed in terms of ease of use, portability of the applications, and preparation of the models for the evaluations. Thus, the case studies added a new dimension to the exploration and understanding of how this new technology could be of practical value in industry.     

Numerical Optimization of an Active Voltage Controller for High-Power IGBT Converters

Feedback control of insulated gate bipolar transistors (IGBTs) in the active region can be used to regulate the device switching trajectory. This facilitates series connection of devices without the use of external snubber networks. Control must be achieved across the full active region of the IGBT and must balance a number of conflicting system goals including diode recovery. To date, the choice of control parameters has been a largely empirical process. This paper uses accurate device models and formalized optimization procedures to evaluate IGBT active voltage controllers. A detailed optimization for the control of IGBT turn-on is presented in this paper     

Using global positioning system for bus priority in London: traffic signals close to bus stops

London's bus network is one of the largest and most comprehensive urban transport systems in the world. The contribution of buses is recognised by implementing a series of initiatives including bus priority at traffic signals. London has a long history of the implementation of bus priority at traffic signals. It has kept pace with the development of new technologies by updating its bus priority system. Now, London is moving towards a bus management system based on global positioning system (GPS), which will also be used to provide bus priority at traffic signals. The authors describe theoretical work carried out by TRG on behalf of Transport for London Bus Priority Team to tackle the challenge posed by locational error associated with GPS where a traffic signal is close to a bus stop     

Chemical Amplification of a Triphenylene Molecular Electron Beam Resist

Molecular resists, such as triphenylene derivatives, are small carbon rich molecules, and thus give the potential for higher lithographic resolution and etch durability, and lower line width roughness than traditional polymeric compounds. Their main limitation to date has been poor sensitivity. A new triphenylene derivative molecular resist, with pendant epoxy groups to aid chemically amplified crosslinking, was synthesized and characterized. The sensitivity of the negative tone, pure triphenylene derivative when exposed to an electron beam with energy 20 keV was ～ 6 × 10^–4 C cm^–2, which increased substantially to ～ 1.5 × 10^–5 C cm^–2 after chemical amplification (CA) using a cationic photoinitiator. This was further improved, by the addition of a second triphenylene derivative, to ～ 7 × 10^–6 C cm^–2. The chemically amplified resist demonstrated a high etch durability comparable with the novolac resist SAL 601. Patterns with a minimum feature size of ～ 40 nm were realized in the resist with a 30 keV electron beam.     

High-level interpretation in virtual environments

As virtual environments applications become more complex, there is a need to interpret user interaction in terms of high-level concepts. In this paper, the relations between conceptual representations of actions and their physical simulation in virtual worlds is investigated. A model inspired fromnatural language processing (NLP) research in the linguistic interpretation of dynamic scenes has been developed. The experiments are based on real-time animation software, which has been enhanced with a symbolic information processing layer, originally developed for NLP-based animation. We report the implementation of a high-level interpretation module that is able to recognize complex actions fromlow-level physical events in the virtual world and discuss its performance as well as directions for further developments.     

A survey of partial differential equations in geometric design

Computer-aided geometric design is an area where the improvement of surface generation techniques is an everlasting demand, since faster and more accurate geometric models are required. Traditional methods for generating surfaces were initially mainly based upon interpolation algorithms. Recently, partial differential equations (PDE) were introduced as a valuable tool for geometric modelling, since they offer a number of features from which these areas can benefit. This work summarizes the uses given to PDE surfaces as a surface generation technique together with some other applications to computer graphics.     

Frustrated-total-internal-reflection fiber-optic pressure sensor

In this work the design and construction of a simple fiber-optic pressure sensor based on the principle of frustrated-total-internal-reflection in a fiber cut beyond the critical angle are described. The characteristic of the device is obtained and compared with the predictions of a simple theory. Modifications to alter its sensitivity by the use of different wavelengths and fiber cut angle are discussed.