INVESTIGATION OF THE USE OF LASER-DOPPLER VELOCIMETRY IN TWO-PHASE BUBBLY FLOWS

Understanding the dynamic phenomena of viability loss of shear sensitive cells and bubble breakage and coalescence within airlift reactors requires knowledge of local, liquid-phase hydrodynamics. The laser-Doppler velocimeter (LDV) is a non-invasive instrument which may be used to obtain this information. Experimental procedures and software were developed to detect and measure Doppler bursts in two-phase flow in a split-cylinder airlift reactor. Off-line analysis of the data indicated a detection rate approximately one order of magnitude greater than that observed using an available commercial frequency tracker. Approximately 400 to 500 observations are needed for the ensemble mean to characterize the local mean velocity to within ±5% for a superficial gas velocity of 10.4 cm/s, the highest superficial gas velocity used in these studies. The limitations, prospects, and signal-processing options for LDV in this application are also discussed     

Synthesis and characterization of poly(keto-amines). 2. Self-polycondensation of 4-methyl-3-aminophenacyl chloride and 2-methyl-4-aminophenacyl chloride

Poly(keto-amines) such as poly(4-methyl-3-iminophenacyls) and poly(2-methyl-4-iminophenacyls) were prepared by self-polycondensation of 4-methyl-3-aminophenacyl chloride and 2-methyl-4-aminophenacyl chloride under different experimental conditions. All the polymer samples were insoluble in common organic solvents. They were characterized by elemental analysis, IR spectral studies, estimation of M?_n by non-aqueous conductometric titration and study of thermal properties by DTA. The properties of P4M3IP and P2M4IP were compared with those of poly(4-iminophenacyls).     

Grafting of methyl methacrylate onto guar gum by hydrogen peroxide initiation

Graft copolymerization of methyl methacrylate (MMA) onto guar gum (GG) in aqueous slurry has been carried out using hydrogen peroxide (H₂O₂) as initiator. The copolymers were characterized by infrared spectroscopy. The grafting parameters like percent grafting, grafting efficiency, percent add-on, and the grafting frequency were determined, and the effect of reaction time, concentration of initiator, and [GG]/[MMA] ratios on the grafting parameters have been discussed. The decrease in % add-on at increasing concentration of H₂O₂ indicated enhancement in the rate of homopolymerization of methyl methacrylate.     

Predicting elastic moduli of heterogeneous polymer compositions

A new method for predicting elastic moduli M of heterogeneous polymer compositions is proposed. It is based on a phenomenological adjustment between parallel and series models for upper and lower bound moduli M_U and M_L. Thus, where ?_H is the volume fraction of hard phase, ?_S is the volume fraction of soft phase, and n is the only adjustable parameter since the upper and lower bound moduli are given by and where M_H and M_S are the moduli of the pure hard and soft phases, respectively. Predicted values of M are in agreement with measured values in a number of systems which include polyblends and composite materials of fixed morphology. The significance of n is discussed relative to concentrations in the area of a phase transition for the polyblends or relative to phase morphology in the case of fixed morphology compositions. Interestingly, the relationship, by analogy, is in agreement with measured values of polyblend melt viscosities.     

A study on adsorption of poly(methyl methacrylate) on aluminium silicate

Effect of temperature, solvent power, and molecular weight on the adsorption of poly methyl methacrylate (PMMA) on aluminium silicate has been studied. Kinetics of adsorption have been also investigated at 30° and 45 °C. The values of rate constants at these temperatures are 1.4 · 10^?2 and 1.0 · 10^?2 min^?1 respectively. The adsorption data have been analysed according to the Langmuir and the Simha -Frisch -Eirich (SFE) isotherms. The results could be adequately explained in terms of the Langmuir isotherm.     

Frequency distributions of breaking load,tenacity, and ratio of cell wall thickness to ribbon width for single cotton fibers

Analysis of the frequency distributions of breaking load, tenacity, and ratio of cell wall thickness to ribbon width (C/R) for single cotton fibers in this study has indicated that they can all be represented by β-distributions. This suggests that a parallel model of element configurations exists in which there is a uniform distribution of elemental strengths in single cotton fibers before as well as after slack mercerization. In the case of breaking load and tenacity, the distributions are positively skewed and the skewness decreases on slack mercerization, suggesting that quite a few potentially weak places have been either completely removed or at least strengthened. The changes in C/R ratio on slack mercerization for cottons having a range of maturity have been examined and discussed. The dependence of properties such as breaking load, tenacity, and linear density on cell wall to ribbon width ratio (C/R) have also been studied.     

HYDRODYNAMIC STUDIES IN FISCHER-TROPSCH DERIVED WAXES IN A BUBBLE COLUMN

Gas hold-up and Sauter mean bubble diameter measurements were made in a 0.051 m diameter by 3 m long glass bubble column in the system, nitrogen-molten wax, with three different waxes (paraffin wax FT-300, Sasol's Arge wax and Mobil's reactor wax). Paraffin wax has a tendency to foam and gas hold-up is a strong function of gas distributor type, temperature and start-up procedure, whereas the reactor waxes do not foam and are much less affected by these variables, In experiments at 265°C with a 1.85 mm single hole orifice plate distributor the gas hold-ups were nearly the same for all three waxes. However, significant differences in Sauter mean bubble diameters were obtained in experiments with different waxes; FT-300 wax produced the smallest Sauter mean bubble diameters whereas Mobil's reactor wax produced the largest bubbles. Addition of 1-octadecanol and octadecanoic acid (up to 10wt%) to the FT-300 paraffin wax caused an increase in gas hold-up and a delay in the foam break-up in runs at 265°C with the 1.85 mm orifice plate distributor.     

Viscosity of binary mixtures. I. mono-, di-, and tri-n-butyl and -n-octylamine with cyclohexane

Viscosities for six binary mixtures of n-butylamine, di-n-butylamine, tri-n-butylamine, n-octylamine, di-n-octylamine, and tri-n-octylamine with cyclohexane have been measured at 303.15 K with an Ubbelohde suspendedlevel viscometer. Deviations of viscosities from a rectilinear dependence on mole fraction are attributed to H-bonding and to the size of alkylamine compounds. The application of the Eyring's theory of activation energy is examined. The free volume theory of Prigogine-Flory-Patterson (PFP) and the experimental excess enthalpy have been used to estimate excess viscosity ln = (ln / ₁ ⁰ – x ₂ ln ₂ ⁰ / ₁ ⁰ ) and corresponding free volume, enthalpy, and entropy contributions for five binary mixtures of tri-n-alkylamine: triethyl, tripropyl, tributyl, trihexyl, and trioctylamine with cyclohexane. A comparison of experimental and theoretical excess viscosities indicates a failure of the PFP theory when two components of the mixture differ considerably in size. The size difference contribution to excess viscosity is related to (V ₂ ^*1/2 – V ₁ ^*1/2 ), where V ₁ ^* and V ₂ ^* are hard-core volumes of two components of the mixture.     

Formulation and development of ophthalmic in situ gel for the treatment ocular inflammation and infection using application of quality by design concept

Context: The conventional liquid ophthalmic delivery systems exhibit short pre-corneal residence time and the relative impermeability to the cornea which leads to poor ocular bioavailability.

Objective: The aim of this study was to apply quality by design (QbD) for development of dexamethasone sodium phosphate (DSP) and tobramycin sulfate (TS)-loaded thermoresponsive ophthalmic in situ gel containing Poloxamer 407 and hydroxyl propyl methyl cellulose (HPMC) K4M for prolonging the pre-corneal residence time, ocular bioavability and decreases the frequency of administration of dosage form. The material attributes and the critical quality attributes (CQA) of the in situ gel were identified. Central composite design (CCD) was adopted to optimize the formulation.

Materials and methods: The ophthalmic in situ forming gels were prepared by cold method. Materials attributes were the amount of Poloxamer 407 and HPMC and CQA identified were Gel strength, mucoadhesive index, gelation temperature and % of drug release of both drug.

Results and discussion: Optimized batch (F*) containing 16.75% poloxamer 407 and 0.54% HPMC K4M were exhibited all results in acceptable limits. Compared with the marketed formulation, optimized in situ gel showed delayed T_max, improved C_max and AUC in rabbit aqueous humor, suggesting the sustained drug release and better corneal penetration and absorption.

Conclusion: According to the study, it could be concluded that DSP and TS would be successfully formulated as in situ gelling mucoadhesive system for the treatment of steroid responsive eye infections with the properties of sustained drug release, prolonged ocular retention and improved corneal penetration.     

Development of porous defects in plasma membranes of adenosine triphosphate-depleted Madin-Darby canine kidney cells and its inhibition by glycine

Studies during the past decade have led to the recognition of a fundamental, widely expressed mechanism of structural damage in energy-deprived cells, which is suppressed by physiologic levels of glycine and is independent of Ca2+ availability or alterations of cytosolic free Ca2+. To gain insight into this process, Madin-Darby canine kidney (MDCK) cells were depleted of adenosine triphosphate (ATP) by a mitochondrial uncoupler in glucose-free medium, and intracellular free Ca2+ was clamped at 100 nM to avoid calcium cytotoxicity. Although the ATP-depleted cells swelled and blebbed and their plasma membranes appeared to be under tension, they nevertheless became permeable to macromolecules. The plasma membranes of these cells retained structural continuity, as determined by morphologic observations, and confocal microscopy of a plasma membrane protein label (Biotin: Ultra Avidin-Texas Red) and a lipid label (NBD-sphingomyelin). Using fluoresceinated dextrans of graded molecular size, membrane permselectivity was examined noninvasively by confocal microscopy. Measured as inside/outside ratios of fluorescence intensity, the permeability indices showed progressively greater restriction to diffusion of increasingly larger dextran molecules across plasma membranes, with sharp break-points between 70,000 and 145,000 daltons (d). The results indicated that the membranes behaved as if they were perforated by water-filled channels or "pores," with size-exclusion limits of molecular dimensions. The membrane defects evolved from small pores permeable only to propidium iodide (668 d) and the smallest dextran (4,000 d), before enlarging with time to become permeable to larger dextrans. Inclusion of glycine during ATP depletion did not affect cell swelling or blebbing but completely prevented the development of permeability defects. Treatment of cells before ATP depletion with a membrane-impermeant homobifunctional "nearest neighbor" cross-linking agent, 3,3' dithiobis(sulfosuccinimidylpropionate), suppressed the development of permeability defects, even in the absence of glycine. These observations suggest that the cellular abnormality that is suppressed by glycine involves rearrangement of plasma membrane proteins to form water-filled pores large enough to leak macromolecules.