A combined low temperature water heating system consisting of radiators and floor heating

Space heating load is decreasing in modern Finnish apartments due to lower U-values of the construction, tight envelopes and heat recovery from exhaust ventilation air. This makes it possible to develop a new combined low temperature water heating system with nominal supply/return water temperatures of 45 °C/35 °C. Such a system includes radiators in rooms and floor heating in bathrooms.In this study, the performance of an apartment building is determined by using dynamic simulation. The simulation results for the combined low temperature water heating system are compared with those for three conventional radiator and floor heating systems. The results show that the combined low temperature water heating system performs well and is able to maintain the zones within the required temperature levels. The thermal comfort analysis indicates that the drifts and ramps in operative temperature using the four studied heating systems are within the limits of Ashrae Standard 55-2004.Temperature measurements in a test room are carried out to find the vertical difference of air temperature using two methods: radiator heating and floor heating. These measurements indicate that there is only a small vertical temperature difference that would not produce any significant thermal discomfort.     

Going below the wet-bulb temperature by indirect evaporative cooling: Analysis using a modified ε-NTU method

The objective of this paper is to study a method to achieve sub-wet bulb temperature by indirect evaporative cooling of air (without using a vapor compression machine). For this purpose, an analytical model is developed based on the effectiveness-NTU method (ε-NTU). The main idea for achieving a sub-wet bulb temperature by indirect evaporative cooling of air is by indirectly pre-cooling the working air before it enters the wet passage. It is shown that a modified analytical model for indirect evaporative coolers could be based on the ε-NTU method for sensible heat exchangers when proper adjustments are made by redefining the potential gradients, transfer coefficient, heat capacity rate parameters and assuming a linear saturation temperature-enthalpy relation of air. This modified model is used to find the performance of a regenerative indirect evaporative cooler. The model results show very good agreement with results from experimental measurements and a numerical model.     

Three-dimensional computational micro-mechanical model for woven fabric composites

This work presents a computational material model for plain-woven fabric composite for use in finite element analysis. The material model utilizes the micro-mechanical approach and the homogenization technique. The micro-mechanical model consists of four sub-cells, however, because of the existing anti-symmetry only two sub-cells have to be homogenized for prediction of the elastic material properties. This makes the model computationally very efficient and suitable for large-scale finite element analysis. The model allows the warp and fill yarns not to be orthogonal in the plane of the composite ply. This gives the opportunity to model complex-shaped composite structures with different braid angles. General homogenization procedure is employed with two levels of property homogenization. The model is programmed in MATLAB software and the predicted material properties of different composite materials are compared and presented. The material model shows good capability to predict elastic material properties of composites and very good computational efficiency.     

Sandwich shell finite element for dynamic explicit analysis

The contribution of this paper consists of new development of transverse shear stresses through the thickness and finding an expression for the critical time step for explicit time integration of layered shells. This work presents the finite element (FE) formulation and implementation of a higher‐order shear deformable shell element for dynamic explicit analysis of composite and sandwich shells. The formulation is developed using a displacement‐based third‐order shear deformation shell theory. Using the differential equilibrium equations and the interlayer requirements, special treatment is developed for the transverse shear, resulting in a continuous, piecewise quartic distribution of the transverse shear stresses through the shell thickness. Expressions are developed for the critical time step of the explicit time integration for orthotropic homogeneous and layered shells based on the developed third‐order formulation. To assess the performance of the present shell element, it is implemented in the general non‐linear explicit dynamic FE code DYNA3D. Several problems are solved and results are presented and compared to other theoretical and numerical results. Copyright © 2002 John Wiley & Sons, Ltd.     

Photodegradation of phenol red in the presence of oxyhydroxide of Fe(III) (Goethite) under artificial and a natural light

The (α‐FeOOH) Goethite composite is a stable and an efficient catalyst in aqueous suspension under irradiation at 365 nm and by solar light. The photocatalytic activities of this composite were evaluated using Phenol Red (PR) dye (phenolsulfonphthalein class). In the dark, controlling factors, such as the pH and the adsorption of PR on Goethite surface were evaluated (before starting the photochemical experiments). It was found that the system PR‐Goethite present a small decrease in the main band of the dye (435 nm) which was explained by the low rate of adsorption of this dye on the Goethite. Also, we note that 40% of PR decolourisation was obtained after 200 min by the system PR‐Goethite‐hydrogen peroxide (H₂O₂) in dark due to the formation of ^?OH by thermal decomposition of H₂O₂ on the surface of Goethite. The effects of various experimental parameters, such as initial dye concentration, pH, photocatalyst amount, tert‐Butyl alcohol effect and H₂O₂ addition were investigated in the study of photodegradation of the dye. The results showed that the photodegradation of PR under UV‐A (365 nm) irradiation could be enhanced greatly in the presence of H₂O₂. Natural radiation tests (under sunlight) showed that degradation was faster comparing with that obtained using the artificial one at 365 nm. Studies of the mineralization using total organic carbon method under naturel light certify that this method, compatible with the environment, may be considered in the treatment of wastewater and generally in the process of removal of this kind of pollutant.     

Integrated electrokinetic-soil flushing to remove mixed organic and metal contaminants

The integrated use of hydraulic flushing and electrokinetic treatment was investigated for the remediation of silty sand contaminated by both PAHs and heavy metals. The soil was collected from a polluted former manufactured gas plant (MGP). Four bench-scale experiments were conducted to analyze the ability of the combined hydraulic flushing and the electrokinetic treatment for the simultaneous removal of PAHs and heavy metals. Sequential flushing with ethylenediaminetetraacetic acid (EDTA) or Igepal CA-720 were tested with or without the simultaneous application of a low intensity direct electric field (1 VDC cm⁻¹). The best results were obtained with 0.2 M EDTA flushing in two stages (without and with voltage gradient, 1 VDC cm⁻¹), followed by 5% Igepal flushing in two stages (without and with 1 VDC cm⁻¹). Heavy metals were removed mainly during the EDTA flushing, with removal efficiencies of about 60% for Zn, 80% for Pb, and 30% for Cu. During Igepal flushing, no heavy metals were removed, but PAHs were removed, including 40% phenanthrene, 30% pyrene, and 20% benzo[a]pyrene. Overall, this study showed that a carefully designed sequential hydraulic flushing scheme with selected chelant and surfactant is needed for the removal of both heavy metals and PAHs from MGP silty sands. Combining electrokinetics with hydraulic flushing may not necessarily improve contaminant removal from such soils.     

A multi-verse optimizer approach for feature selection and optimizing SVM parameters based on a robust system architecture

Neural Computing and Applications - Support vector machine (SVM) is a well-regarded machine learning algorithm widely applied to classification tasks and regression problems. SVM was founded based...     

Influence of surface evaporation on stratification in liquid hydrogen tanks of different aspect ratios

The effect of evaporation on stratification in large liquid hydrogen storage tanks of different aspect ratios is computed. A homogeneous two-phase model is used and the continuity, momentum and energy equations for the two phases are solved. Evaporation at the liquid–vapor interface is incorporated through a source term for mass transfer. The amount of stratification is seen to progressively increase as the aspect ratio of the tanks increases. However, the surface evaporation brings down the differences in the amount of stratification with changes of aspect ratio. The predictions for stratification in the pre-evaporation and evaporation phases are discussed.     

Efficient PFD-Based Networking and Buffering Models for Improving Video Quality over Congested Links

Video traffic over the Internet becomes increasingly popular and is expected to comprise the largest proportion of the traffic carried by wired and wireless networks. On the other hand, videos are usually compressed by exploiting spatial and temporal redundancy for the reason of increasing the number of video streams that can be simultaneously carried over links. Unfortunately, receiving high-quality video streaming over the Internet remains a challenge due to the packet loss encountered in the congested wired and wireless links. In addition, the problem is more apparent in wireless links due to not only employing limited system capacity, but also some of the major drawbacks of wireless networks, out of which the bandwidth limitations and link asymmetry which refers to the situation where the forward and reverse paths of a transmission have different channel capacities. Therefore, the wireless hops may be congested which result in dropping many video frames. Additionally, as a result of compressing videos, dependencies among frames and within a frame arise. Consequently, the overall video quality tends to be degraded dramatically. The main challenge is to support the growth of video traffic while keeping the perceived quality of the delivered videos high. In this paper, we extend our previous work concerning improving video traffic over wireless networks through professionally studying the dependencies between video frames and their implications on the overall network performance. In other words, we propose very efficient network and buffer models proportionately to novel algorithms that aim to minimize the cost of aforementioned possible losses by selectively discarding frames based on their contribution to picture quality, namely, partial and selective partial frame discarding policies considering the dependencies between video frames. The performance metrics that are employed to evaluate the performance of the proposed algorithms include the rate of non-decodable frames, peak signal-to-noise ratio, frameput, average buffer occupancy, average packet delay, as well as jitter. Our results are so promising and show significant improvements in the perceived video quality over what is relevant in the current literature. We do not end up to this extent, but rather the effect of producing different bit-stream rates by the FFMPEG codecs on aforementioned performance metrics has been extensively studied.