A Note on PIN Polynomials and PRIN Rational Functions

This brief presents a necessary and sufficient condition for testing positive, real, imaginary, and negative rational functions. A related term, the positive, imaginary, and negative polynomial, is defined and two necessary and sufficient conditions for testing it are given.     

Effect of refraction on optical microscopic measurement of internal blood-vessel diameter and its correction

In optical microscopic measurement of internal blood-vessel diameters, the effect of refraction must be taken into account to ensure accuracy of the result. This effect is discussed and an analytical correction formula derived. Phantom blood vessels with known internal and external diameters were used to test the validity of the correction formula. The errors obtained prior to correction were reduced significantly after correction.     

End-to-End QoS for Video Delivery Over Wireless Internet

Providing end-to-end quality of service (QoS) support is essential for video delivery over the next-generation wireless Internet. We address several key elements in the end-to-end QoS support, including scalable video representation, network-aware end system, and network QoS provisioning. There are generally two approaches in QoS support: the network-centric and the end-system centric solutions. The fundamental problem in a network-centric solution is how to map QoS criterion at different layers respectively, and optimize total quality across these layers. We first present the general framework of a cross-layer network-centric solution, and then describe the recent advances in network modeling, QoS mapping, and QoS adaptation. The key targets in end-system centric approach are network adaptation and media adaptation. We present a general framework of the end-system centric solution and investigate the recent developments. Specifically, for network adaptation, we review the available bandwidth estimation and efficient video transport protocol; for media adaptation , we describe the advances in error control, power control, and corresponding bit allocation. Finally, we highlight several advanced research directions.     

Effects of grain sizes, shapes, and distribution on minimum sizes of representative volume elements of cubic polycrystals

In the literature the concept of representative volume element (RVE) was introduced to correlate the effective or macroscopic properties of materials with the properties of the microscopic constituents and microscopic structures of the materials. However, to date little quantitative knowledge is available about minimum RVE sizes of various engineering materials. In our recent paper [J. Mech. Phys. Solids 50 (2002) 881], a new definition of minimum RVE size was introduced based on the concept of nominal modulus. Numerical experiments using the finite element method (FEM) were then carried out for determining the minimum RVE sizes of more than 500 cubic polycrystals in the plane stress problem, under the assumption that all grains in a polycrystal have the same square shape––called the simple polycrystal model. The major finding is that the minimum RVE sizes for effective elastic moduli have a roughly linear dependence on crystal anisotropy degrees. The present paper takes into account the effect of grain sizes, shapes, and distribution on the minimum RVE sizes for real cubic polycrystals that are formed by crystallization processes. Similar roughly linear dependence is found again, with the slope about 19% lower than that in the simple polycrystal model. This finding is interesting and useful because numerical experiments on minimum RVE sizes for a large number of crystals are quite time-consuming and the simple polycrystal model reduces significantly the FEM pre- and post-processing works. This should be particularly true in numerically testing minimum RVE sizes for three-dimensional polycrystals and for nonelastic properties in future works. With a maximum relative error 5%, all the polycrystals tested have a minimum RVE size of 16 or less times the grain size.     

Studies on adsorption equilibrium of xylenes in AEL framework using biased GCMC and energy minimization

The adsorption of xylene isomers in AlPO₄-11 (AEL network) was investigated using biased grand canonical Monte Carlo (GCMC) simulations. Preferential o-xylene adsorption was predicted by the simulations, in agreement with previously reported experimental data. In AlPO₄-11 the selective adsorption behavior comes from the smaller length of the o-xylene molecule along the crystallographic c-axis compared to p-xylene. This is in contrast to AlPO₄-5 and AlPO₄-8, where the ortho-selectivity is caused by the characteristic face-to-face positioning of o-xylene. Energy minimization studies were also performed in a flexible AlPO₄-11 lattice to study the structural changes upon xylene adsorption. The energy minimization study showed that the AlPO₄-11 crystal distorts upon p- and o-xylene adsorption. The distortion mechanism is related to the strong interaction between xylene methyl groups and the sieve oxygen atoms in the O3 position in the wide region of the pore.     

Driving Mechanisms of Delamination Related Reliability Problems in Exposed Pad Packages

Exposed pad packages were introduced in the late 1980s and early 1990s because of their excellent thermal and electrical performance. Despite these advantages, the exposed pad packages experience a lot of thermo-hygro-mechanical related reliability problems during qualification and testing. Examples are die lift, which occurs predominantly after moisture sensitivity level conditions, and die-attach to leadframe delamination leading to downbond stitch breaks during temperature cycling. In this chapter, nonlinear finite element (FE) models using fracture mechanics based J-integral calculations are used to assess the reliability problems of the exposed pad package family. Using the parametric FE models any geometrical and material effects can be explored to their impact on the occurrence diepad delamination, and dielift. For instance the impact of diepad size is found to be of much less importance as the impact of die thickness is. Using the fracture mechanics approach, the starting location for the delamination from thermo-hygro-mechanical point of view is deducted. The results indicate that when diepad delamination is present, cracks are likely to grow beneath the die and dielift will occur. The interaction between dielift and other failure modes, such as lifted ball bonds, are not found to be very significant. The FE models are combined with simulation-based optimization methods to deduct design guidelines for optimal reliability of the exposed pad family.