A new process of fabricating inverted-staggered tri-layer thin-filmtransistors

A new method of fabricating a-Si:H TFT with etching-stop structure has been proposed. Only one plasma-enhanced chemical vapor deposition is required in this new method and a PH₃/H₂ plasma treatment during the deposition has been used to form the TFT contact and thus saved another plasma deposition. With this method, a TFT of 500 Å active layer has been fabricated successfully. The drain current and saturation mobility of this device is 2.4×10^-7 A and 0.1 cm²/V sec, respectively, which is comparable to the conventional fabricating method. The plasma treatment will also form an additional leakage path on the TFT top surface and increase the TFT subthreshold slope. However, a current of less than 1 pA at V_G=-2.4 V can still be obtained. The possible mechanism of the contact formation by the plasma treatment is also discussed     

Robust controller with disturbance rejection for hydraulic servosystems

A controller is presented that improves the performance and reduces the sensitivity of hydraulic servo systems in the presence of parameter variations, nonlinear effects, and other disturbances. The control system has enhanced closed-loop stability and can recover from steady-state and transient error quickly and completely. It consists of a servo controller, an auxiliary controller, and a robust controller. Simulation and experimental results demonstrate the validity of the controller     

Laser glazing of an Fe-C-Sn alloy

Morphology and geometry of melted zones, cooling rates, microstructure and microhardness in the laser-glazed Fe-4%C-10%Sn alloy have been investigated. The computer simulation on the basis of the moving gaussian source model was used successfully to predict the maximum width and depth of the melted zone and the cooling rate. The microstructure from the surface to the bottom of the laser-melted zone is a non-crystalline phase, dendritic grains and a microcrystalline zone successively. Values of the averaged-spacing of the non-crystalline phase are 0.205⁶ and 0.121⁹nm, respectively; twinned martensites, having an axial ratioc/a of 1.128, existed in dendritic grains, and carbides of Fe₃ C at the interdendritic regions; the microcrystalline zone was composed of -Fe and a new bet (a=0.415 nm,c=0.955 nm) phase. The different microstructure in the melted zone can be explained by the results of the heat flow calculation. A fine eutectic structure (-Fe + Fe₃C) was observed in heat-affected zones. Microhardness of the eutectic structure can be predicted by the empirical relation of fracture stress to the interlamellar spacing of pearlite.     

A study on bioglass ceramics in the Na2O-CaO-SiO2-P2O5 system

A new bioglass ceramic with composition of Na₂O 12%, CaO 28%, P₂O₅ 10% and SiO₂ 50% with a high bending strength (120–140 MPa) and compressive strength (600–750 MPa) was studied. The crystallized phases of-Ca₂P₂P₇ and Na₂Ca₃Si₆O₁₆ were determined by X-ray diffraction. Optical microscopy of the material revealed that a very uniform crystal size of about 30 m was obtained with high nucleation frequency. The nucleation and crystallization processes were also investigated. The rat shoulder test showed that the material formed a tight chemical bond with biological texture and had good biocompatibility.     

经食道心房调搏的放射性核素心血管造影

本文应用反符合电路剔除调搏脉冲干扰的方法,制成经食道心房调搏心电心音门电路触发装置,用于经食道心房调搏的核素心血管造影。参考Tzivoni标准,当逐级增加调搏心率至140次/min或亚极量心率后发现:冠心病人有调搏后EF降低;急性心肌梗塞病人EF减低更为明显,并呈室壁反向运动。因此,心房调搏核素心血管造影有助于冠心病,特别是心肌梗塞的诊断。     

铝阳极氧化膜颜色的检验和观察法

介绍铝及铝合金阳极氧化膜颜色的概念和描写,对颜色的儿种测量方法进行了比较,重点分析观察法及其在各国标准中的异同。在此基础上,提出了GB8013中的对颜色进行观察的条件和理论根据。     

Pd/Mg(OH)2 Heterogeneous Nanocatalysts Synthesized by a Facile One-Pot Hydrothermal Method for CO Direct Esterification to Dimethyl Oxalate

Catalysis Letters - Pd-based heterogeneous nanocatalysts have wide application in chemical industry. However, the traditional synthesis process contains multi-steps such as impregnation, dry,...     

Study on heat conduction and adsorption/desorption characteristic of MIL-101/few layer graphene composite

Journal of Porous Materials - Aiming at the poor heat conduction performance of porous MIL-101 applied in adsorption cooling process, few layer graphene (FLG) was selected as a promising thermal...     

二氧化硅包覆CsPbI3纳米晶薄膜的制备

卤化钙钛矿型(ABX3)纳米材料是近几年兴起的光电新材料,由于全无机钙钛矿CsPbX3(X=Cl,Br,I)纳米晶体的稳定性差,严重阻碍了实际应用,但因其具有窄带隙,在太阳能电池领域有着重要的应用前景.本研究在CsPbI3纳米晶周围使硅酸四甲酯(TMOS)发生水解反应,形成CsPbI3@SiO2纳米晶体复合材料,促使甲苯悬浮液的稳定性显著提高,发光稳定性可增加到29 d.通过进一步以聚(苯乙烯-乙烯-丁二烯-苯乙烯)三嵌共聚物(SEBS)对复合材料进行包裹,得到具有良好透明性和可拉伸性的SEBS/CsPbI3@SiO2薄膜,在水中有保持24 h稳定荧光现象,在水中12 h能保持原有发光强度的53％,而未经二氧化硅包裹的SEBS/CsPbI3纳米晶薄膜在水中仅8 h就失去荧光.本研究不仅为CsPbX3的表面改性提供了一种新方法,有助于解决稳定性问题,而且以聚合物复合的薄膜具有可拉伸性,也可应用在柔性器件中,具有重要的应用价值.     

风轮模拟试验平台的仿真与研究

分析风力机的特性,在上位机上搭建风力机的模型,通过上位机对变频器输入指令以实现对异步电机的控制,通过光电编码器和USB数据采集卡实现转速采集.设计一套基于LabVIEW的风轮模拟试验平台,为试验室的无风环境提供可控风速.提出一种转速控制方案并实现仿真,便于进行风力发电技术的研究.