Cerebral protection by intermittent reperfusion during temporary focal ischemia in the rat

Temporary arterial occlusion has been routinely used as an adjunct in intracranial aneurysm surgery. This has commonly been performed using a protocol of multiple short periods of occlusion alternating with periods of restoration of normal circulation. Recently, the logical basis of this method has come under scrutiny. There is extensive experimental evidence to suggest that repetitive, brief periods of global ischemia may cause more severe cerebral injury than an equivalent single period of global ischemia. Only recently has this issue begun to be addressed with regard to focal ischemia. Hence, despite the common use of temporary clipping, little experimental data are available regarding the ischemic consequences of temporary arterial occlusion with periods of reperfusion versus uninterrupted temporary occlusion. To investigate this issue, a protocol of occlusion/reperfusion that simulates the temporal profile that occurs during surgery was performed in a rat model of focal ischemia. Sixteen anesthetized Sprague-Dawley rats were divided into two groups. The animals in Group I underwent 60 minutes of uninterrupted middle cerebral artery occlusion and the animals in Group II were subjected to six separate 10-minute occlusion periods with 5 minutes of reperfusion between occlusions. Histopathological analysis was performed 72 hours postischemia. Group I had significantly increased mean infarction volumes (50.0 +/- 12.1 mm3) compared to Group II (8.7 +/- 3.1 mm3) (p = 0.008). Injuries in Group I occurred in both the cortex and striatum, whereas Group II showed only striatal injuries. Furthermore, the extent of the injuries in Group II was less severe, characterized by ischemic neuronal injury rather than frank infarction. The results indicate that intermittent reperfusion is neuroprotective during temporary focal ischemia and support the hypothesis that intermittent reperfusion is beneficial if temporary clipping is required during aneurysm repair.     

Room temperature characterization of Hg1-xCdxTe P-on-n heterostructure photodiodes

Measurements of 77K R_oA and 300K reverse bias dynamic impedance (R_dA) products at one volt reverse bias has been carried out to assess the degree of correlation of this figure of merit. Planar P-on-n heterostructures were grown on near lattice-matched CdZnTe substrates with Hg_1-xCd_xTe (0.20< x <0.30) by molecular beam epitaxy. These devices were passivated with CdTe and doped with indium and arsenic as n- and p-type dopants, respectively. Current-voltage characteristic of these devices exhibit thermally generated dark currents at small and modest reverse bias. We have observed that R_oA values of these long wavelength infrared P-on-n heterostructure photodiodes at 77K correlate with room temperature R_dA values. Diode arrays with high room temperature R_dA values at one volt reverse bias also have high R_oA values at 77K. Similarly, low R_dA values at room temperature indicate poor performance at 77K where deviation from diffusion current occurs at reverse bias of 0.2 to 1 volt at room temperature. The results presented here, for a small samples of devices, demonstrate that room temperature measurements of current-voltage characteristics to evaluate Hg_1-xCd_xTe (0.22< x <0.28) diode performance and array uniformity at lower temperatures can be used. This provides an acceptable criteria for further study at lower temperatures.     

AC measurements of the minimum longitudinal resistance of a QHEsample from 10 Hz to 10 kHz

AC measurements of the longitudinal resistance, R_xx, of a quantum Hall effect (QHE) sample have been made in a frequency range from 10 Hz to 10 kHz. The results show no frequency effect on the minimum value of R_xx corresponding to the quantum numbers i=2 and i=4, within the measurement resolution of 0.5 mΩ. Therefore, the influence of frequency on the value of the quantized Hall resistance, R_H, should not exceed a few parts in 10⁹ . Some unwanted effects detected during the development of the resistance bridge have been pointed out     

Motion of a solid sphere in a general flow near a plane boundary at zero Reynolds number

It is demonstrated how the hydrodynamic force and moment of force acting on a solid sphere may be calculated when it is placed at rest at an arbitrary position in a two dimensional flow at zero Reynolds number in which the region of flow is bounded by either an undeformable planar free surface or by a plane solid wall. The results so obtained are used to calculate the motion of a freely moving solid sphere in an asymmetric vortex in the presence of an underformable free surface. It is seen that the sphere, depending on the direction of the undisturbed flow, will either spiral into or out of the vortex. This implies that when a dilute suspension of such spherical particles undergoes such a vortex motion in the presence of the free surface, the vortex will either fill up with particles from the surrounding flow or become devoid of particles.Deceased, July 31, 1995     

Melt-extracted oxide ceramic fibres — the fundamentals

A melt-extraction technique, using a sharpened molybdenum wheel, has been used to produce fine oxide ceramic fibres. Wetting of the molybdenum wheel by molten ceramic is a key parameter in the melt-extraction process. Two types of fibre are generally obtained, depending on the extraction speed. At very low wheel speed, fine and uniform fibres of high quality are produced. However, when the wheel speed exceeds a critical velocity, Rayleigh waves are formed on the free surface of the fibres. Moreover, the average fibre thickness first increases with the wheel velocity, then passes through a maximum, decreasing at high velocity. This thickness variation is discussed in terms of both surface tension and viscosity of the liquid ceramics.     

Batch-means control charts for autocorrelated data

Modern statistical process control must often cope with large quantities of highly autocorrelated data. Alwan and Radson (1992) proposed the monitoring of autocorrelated processes by plotting the averages of small batches of data separated by skipping observations. Using results for the AR(1) process, we show that generally better performance can be achieved with no skipping and much larger batch sizes. The resulting batch-means charts derive from methods used in simulation output analysis and can be implemented easily with common digital control systems.     

Experimental and numerical investigation of fracture in double-edge notched steel plates

Double-edge notched (DENT) steel plates were pulled until complete fracture and several experimental observations were made (using profilometry and scanning electron microscopy). The essential work of fracture (EWF) model was found to be well verified. Numerical simulations—up to the maximum load only—of some experiments were performed using the finite element method (FEM), and incorporating geometric and material non-linearities (large deformation elasto-plasticity). Some experimental measurements were compared with the corresponding numerical computations and excellent agreement was found.