Special finite elements with holes and internal cracks

For the numerical treatment of stress concentration problems in plane elasticity, special finite elements with circular and elliptic holes and internal cracks have been developed. Two different variational formulations have been used to construct elements, which may be combined with conventional displacement elements. Using complex functions and conformal mapping techniques the systematic construction of trial functions is shown which not only satisfy a priori the governing differential equations but also the boundary conditions on such influential boundary portions as hole or crack surfaces. For the evaluation of the stiffness matrices of the special elements, only boundary integral computations arc necessary. The numerical results of various examples are very accurate for both functionals.     

An enhanced zone 3 algorithm of a distance relay using transient components and state diagram

Zone 3 of a distance relay is used to provide the remote backup protection in case of the failure of the primary protection. However, the risk of maloperation under stressed conditions such as heavy loading, voltage, and transient instability is quite high. Zone 3 is used in combination with the derivatives of the voltage and current, etc. to prevent maloperation. At times, the impedance characteristics that restrict the tripping area of relay are used to avoid maloperation due to load encroachment. This work presents a novel zone 3 scheme based on combining the steady-state components (i.e., 60 Hz) and the transient components (TCs) using a state diagram that visualizes the sequence of studies that emanate from the sequence of events. The simulation results show that the novel zone 3 distance relay elements using the proposed method operate correctly for the various events.     

Uptake of 226radium and 228radium by the lichen genus Umbilicaria

The 226Ra and 228Ra content of the lichens Umbilicaria cylindrica, U. deusta, U. murina and U. hirsuta has been determined as a function of the growth altitude above sea level, based on data derived from material collected from localities in southwest Poland. These data are interpreted as graphs and formulae to show the influence of environmental factors, particularly altitude, on the concentration of 226Ra and 228Ra, and the coefficients of accumulation calculated.     

Kinetic studies of the electrochemical reaction between lithium and phthalocyanine II. Reduction reaction mechanism

The effects, during formation, of current density, charge capacity, and concentration and temperature of H₂SO₄ electrolyte on the capacity of tubular electrodes in lead/acid batteries have been studied. Electrode capacity was found to be maximum at a H₂SO₄ concentration of 1.05 sp. gr., a charge amount of 250% theoretical capacity, a current density of 0.44 A dm^?2, and an electrolyte temperature of 40 °C. A study of the soaking process for tubular electrodes showed the electrode capacity to be maximum when the acid absorption was about 170 mg of H₂SO₄ per g of oxide. Finally, the discharge overpotential of tubular electrodes was analyzed by a galvanostatic transient method.     

Effect of pulse duration and size of interelectrode interval on electric-spark spraying. I. Effect of pulse duration and size of interelectrode interval on rate of electric-spark transfer

The influence exerted by electric-spark spraying on the kinetics of mass transfer and the physicomechanical properties of coatings is investigated. It is shown that electric-spark spraying is determined by the dynamic properties of the cathode jets, which depend on the electrical parameters of the spark discharge, the size of the interelectrode interval, and the physical properties of the coatings, which vary during spraying.     

Simultaneous visualisation of biofouling, organic and inorganic particle fouling on separation membranes.

Fouling is a major problem in membrane processes of water treatment. It can be caused by the deposition of inorganic and organic particulate material, and of microbial cells which may subsequently form biofilms. In practice, usually more than one foulant participates in the formation of membrane deposits. Knowledge of the composition of fouling layers is important for the development of appropriate countermeasures. For this purpose, an experimental system was established for the generation and microscopic visualisation of mixed deposits, using fluorescently labelled model foulants: (i) drinking-water bacteria stained with nucleic acid-specific dyes (biofouling), (ii) synthetic clay mineral laponite stained with rhodamine 6G (inorganic particle fouling), and (iii) fluorescently labelled polystyrene microspheres (organic particle fouling). Polycarbonate and polyethersulfone membranes were challenged with these foulants by dead-end filtration. On the basis of different fluorescent labels, the single foulants in these mixed deposits could be visualised separately by confocal laser scanning microscopy which, in combination with image analysis, allowed the generation of three-dimensional views of the complete deposits. This method offers the possibility for the estimation of quantitative surface coverage by foulants and for the determination of the efficacy of cleaning measures with respect to the removal of different foulants.