Intergranular corrosion of a light aircraft aluminum alloy propeller

Examination of the wreckage of a light aircraft revealed that approximately 20 cm was missing from one tip of the aluminum alloy propeller. Fractographic and metallographic examination of the remaining portion of the propeller revealed extensive grain-boundary separation in the vicinity of the fracture, and grain edges and corners rounded by corrosion on the fracture surface. Energy dispersive X-ray analysis (EDXA) revealed fluorine on, and in the vicinity of, the fracture surface. In the ensuing litigation, it was asserted that the crash occurred because the propeller fractured in flight as the result of intergranular attack caused by the use of a fluorine-bearing cleaner.     

Three takes on telecom's troubles

Spectrum asked three IEEE members from the telecommunications sector to comment on the industry's current woes and prospects. Roch Guerin discusses bandwidth as a commodity and how to deal with it. The impact of technological change on telecommunications is enormous and calls for a shift in business models. Technology is making bandwidth a commodity and it should not matter who supplies it. Competition is vital and commodity providers must be decoupled from value providers. Frank Ferrante points out that the Year 2000 crisis resulted in manufacturers being deluged with orders for new upgraded systems. Vast sums were spent to meet the demand in time. However, when Y2K was over, production stayed high and inventories continued to build, while demand effectively stopped overnight. Dazzling new innovations are needed to compel the masses to spend and manufacturers must apply their resources to deliver quickly and efficiently. Jules A. Bellisio discusses the role of engineers in bringing new ideas to the market place. Many engineers have put together ventures for the sole purpose of attracting capital. The underlying technology and business propositions were there solely to lure the unsuspecting. By allowing engineers to use technology simply to cover for a scam, then the profession is also to blame for the current problems.     

A novel driver assist stability system for all-wheel-drive electric vehicles

A novel driver-assist stability system for all-wheel-drive electric vehicles is introduced. The system helps drivers maintain control in the event of a driving emergency, including heavy braking or obstacle avoidance. The system comprises a fuzzy logic system that independently controls wheel torque to prevent vehicle spin. Another fuzzy wheel slip controller is used to enhance vehicle stability and safety. A neural network is trained to generate the required reference for yaw rate. Vehicle true speed is estimated by a sensor data fusion method. The intrinsic robustness of fuzzy controllers allows the system to operate in different road conditions successfully. Moreover, the ease of implementing fuzzy controllers gives a potential for vehicle stability enhancement.     

Low supply voltage high-performance CMOS current mirror with low input and output voltage requirements

This paper presents a scheme for the efficient implementation of a low supply voltage continuous-time high-performance CMOS current mirror with low input and output voltage requirements. This circuit combines a shunt input feedback and a regulated cascode output stage to achieve low input resistance and very high output resistance. It can be used as a high-precision current mirror in analog and mixed signal circuits with a power supply close to a transistor's threshold voltage. The proposed current mirror has been simulated and a bandwidth of 40 MHz has been obtained. An experimental chip prototype has been sent for fabrication and has been experimentally verified, obtaining 0.15-V input-output voltage requirements, 100-/spl Omega/ input resistance, and more than 200-M/spl Omega/ (G/spl Omega/ ideally) output resistance with a 1.2-V supply in a standard CMOS technology.     

RF microelectronics for W-CDMA mobile communication systems

Third generation (3G) mobile communication systems are now just starting to be introduced. With a maximum data rate of 2 Mbit/s they will make wireless access to broadband data services like the Internet or video applications feasible. Most of the different physical layer technologies summarised under the acronym 3G are based on wideband-CDMA (W-CDMA), in contrast to existing second generation systems, which mostly use TDMA and FDMA. This has severe consequences for the design of the transceiver front-ends. During standardisation these were assumed to have an adequate RF performance yet they still present a performance bottleneck for the system. Starting with a short introduction to UMTS (Universal Mobile Telecommunications System)-the 3G standard to be deployed in Europe and already operating in Japan-this paper describes by way of example some of the test cases specified for UMTS and their impact on the analogue front-end. It is shown that accurate simulation of all the analogue and digital signal processing is necessary in order to predict the RF performance needed of today's commercial RFICs. The paper then presents and reviews some actual design examples. Finally, possible technologies and techniques for application in future mobile terminals are discussed     

Improvement in the DOA estimation of broadband signals usingpartially IIR beamformers

An ideal broadband beamformer requires an increased number of taps for each filter, which in turn increases the complexity of the design. It is shown that for angles near the broadside of the antenna the beamforming is more accurate compared to the angles near the endfire, and it is advantageous to use recursive filters combined with a computed number of zeros for angles near the endfire. The proposed method is used for estimating the arrival angle of the incoming signals and displays uniform accuracy for all angles     

Crosstalk between microstrip transmission lines

Methods for prediction of crosstalk between microstrip transmission lines are reviewed and simplified for the weak-coupling case. Classical coupled transmission line theory is used for uniform lines, and potential and induced EMF methods are used for crosstalk between nonuniform lines. It is shown that the potential method is equivalent to classical coupled transmission line theory for the case of uniform lines. An experiment was performed for uniform coupled microstrip lines for frequencies from 50 MHz to 5 GHz, and good agreement between theory and measurement was obtained for both near- and far-end crosstalk     

A base-band NDS electrode configuration for HACT devices

Heterostructure Acoustic Charge Transport (HACT) devices have been fabricated with a new nondestructive sense (NDS) electrode structure that provides for the recovery of base-band signals without the use of an integrating capacitor. This electrode structure provides an output signal comprising an RF carrier at the SAW frequency, amplitude modulated by the sampled input signal which has been delayed by a period proportional to the output electrodes distance from the input diode. The output of the NDS electrode structure is subsequently demodulated to provide the base-band signal