Room temperature characterization of Hg1-xCdxTe P-on-n heterostructure photodiodes

Measurements of 77K R_oA and 300K reverse bias dynamic impedance (R_dA) products at one volt reverse bias has been carried out to assess the degree of correlation of this figure of merit. Planar P-on-n heterostructures were grown on near lattice-matched CdZnTe substrates with Hg_1-xCd_xTe (0.20< x <0.30) by molecular beam epitaxy. These devices were passivated with CdTe and doped with indium and arsenic as n- and p-type dopants, respectively. Current-voltage characteristic of these devices exhibit thermally generated dark currents at small and modest reverse bias. We have observed that R_oA values of these long wavelength infrared P-on-n heterostructure photodiodes at 77K correlate with room temperature R_dA values. Diode arrays with high room temperature R_dA values at one volt reverse bias also have high R_oA values at 77K. Similarly, low R_dA values at room temperature indicate poor performance at 77K where deviation from diffusion current occurs at reverse bias of 0.2 to 1 volt at room temperature. The results presented here, for a small samples of devices, demonstrate that room temperature measurements of current-voltage characteristics to evaluate Hg_1-xCd_xTe (0.22< x <0.28) diode performance and array uniformity at lower temperatures can be used. This provides an acceptable criteria for further study at lower temperatures.     

AC measurements of the minimum longitudinal resistance of a QHEsample from 10 Hz to 10 kHz

AC measurements of the longitudinal resistance, R_xx, of a quantum Hall effect (QHE) sample have been made in a frequency range from 10 Hz to 10 kHz. The results show no frequency effect on the minimum value of R_xx corresponding to the quantum numbers i=2 and i=4, within the measurement resolution of 0.5 mΩ. Therefore, the influence of frequency on the value of the quantized Hall resistance, R_H, should not exceed a few parts in 10⁹ . Some unwanted effects detected during the development of the resistance bridge have been pointed out     

Motion of a solid sphere in a general flow near a plane boundary at zero Reynolds number

It is demonstrated how the hydrodynamic force and moment of force acting on a solid sphere may be calculated when it is placed at rest at an arbitrary position in a two dimensional flow at zero Reynolds number in which the region of flow is bounded by either an undeformable planar free surface or by a plane solid wall. The results so obtained are used to calculate the motion of a freely moving solid sphere in an asymmetric vortex in the presence of an underformable free surface. It is seen that the sphere, depending on the direction of the undisturbed flow, will either spiral into or out of the vortex. This implies that when a dilute suspension of such spherical particles undergoes such a vortex motion in the presence of the free surface, the vortex will either fill up with particles from the surrounding flow or become devoid of particles.Deceased, July 31, 1995     

Melt-extracted oxide ceramic fibres — the fundamentals

A melt-extraction technique, using a sharpened molybdenum wheel, has been used to produce fine oxide ceramic fibres. Wetting of the molybdenum wheel by molten ceramic is a key parameter in the melt-extraction process. Two types of fibre are generally obtained, depending on the extraction speed. At very low wheel speed, fine and uniform fibres of high quality are produced. However, when the wheel speed exceeds a critical velocity, Rayleigh waves are formed on the free surface of the fibres. Moreover, the average fibre thickness first increases with the wheel velocity, then passes through a maximum, decreasing at high velocity. This thickness variation is discussed in terms of both surface tension and viscosity of the liquid ceramics.     

Batch-means control charts for autocorrelated data

Modern statistical process control must often cope with large quantities of highly autocorrelated data. Alwan and Radson (1992) proposed the monitoring of autocorrelated processes by plotting the averages of small batches of data separated by skipping observations. Using results for the AR(1) process, we show that generally better performance can be achieved with no skipping and much larger batch sizes. The resulting batch-means charts derive from methods used in simulation output analysis and can be implemented easily with common digital control systems.     

Experimental and numerical investigation of fracture in double-edge notched steel plates

Double-edge notched (DENT) steel plates were pulled until complete fracture and several experimental observations were made (using profilometry and scanning electron microscopy). The essential work of fracture (EWF) model was found to be well verified. Numerical simulations—up to the maximum load only—of some experiments were performed using the finite element method (FEM), and incorporating geometric and material non-linearities (large deformation elasto-plasticity). Some experimental measurements were compared with the corresponding numerical computations and excellent agreement was found.     

Tablet Excipients to the Year 2001: A Look into the Crystal Ball

The future for tablet excipients is reviewed from a number of viewpoints: new materials, formulation development, quality, regulatory aspects, logistics, and production. The field of excipients is changing rapidly in response to economic, regulatory, and scientific pressures. As our understanding of drug delivery improves, so will the demands we place on excipients and on their quality, both chemical and functional. In order to fully optimize drug delivery systems, a better understanding of excipients and their properties and limitations is required. The materials science approach to the study of excipients will help to increase our understanding of excipients and how best to use them. But excipients are only one part of the very complex mechanism whereby new medicinal products are brought to the marketplace. It is important that the processes of formulation design and development are properly integrated to obtain optimized drug delivery systems as early as possible. Developments in related fields such as manufacturing technology, logistics, and analytical techniques will also influence the field of excipients.