Scaling planar silicon devices

The generation-over-generation scaling of critical CMOS technology parameters is ultimately bound by nonscalable limitations, such as the thermal voltage and the elementary electronic charge. Sustained improvement in performance and density has required the introduction of new device structures and materials. Partially depleted SOI, a most recent MOSFET innovation, has extended VLSI performance while introducing unique idiosyncrasies. Fully depleted SOI is one logical extension of this device design direction. Gate dielectric tunneling, device self-heating, and single-event upsets present developers of these next-generation devices with new challenges. Strained silicon and high-permittivity gate dielectric are examples of new materials that will enable CMOS developers to continue to deliver device performance enhancements in the sub-100 nm regime.     

Effects of SiN passivation and high-electric field on AlGaN-GaN HFET degradation

The authors report on the effects of silicon nitride (SiN) surface passivation and high-electric field stress (hot electron stress) on the degradation of undoped AlGaN-GaN power HFETs. Stressed devices demonstrated a decrease in the drain current and maximum transconductance and an increase in the parasitic drain series resistance, gate leakage, and subthreshold current. The unpassivated devices showed more significant degradation than SiN passivated devices. Gate lag phenomenon was observed from unpassivated devices and removed by SiN passivation. However, SiN passivated devices also showed gate lag phenomena after high-electric field stress, which suggests possible changes in surface trap profiles occurred during high-electric field stress test.     

Nonstationary Simulation Model of Absorber with Falling Film of Suspension

A nonstationary model of SO₂ absorption from a gas phase to a countercurrent falling film of absorbing slurry was developed. Laminar, wavy and turbulent film structures were considered based on published information. Resistances to the mass transfer on the gas and the liquid sides of the interphase were considered, together with chemical reactions in the liquid phase. Relevant chemical equilibria in the liquid phase were modeled. Original experimental data on the neutralization reagent dissolution rate presented as a polydispersed two‐phase system of solids and on the rate of dissolved sulfite oxidation were used. The model was verified with experimental data from a laboratory‐scale falling‐film absorber using a single vertical tube under various geometrical and operating conditions, and a very good agreement was found with the experiment. Parametric sensitivity analysis showed the critical parts of the model.     

The effects of nonlocal impact ionization on the speed of avalanche photodiodes

The nonlocal enhancement in the velocities of charge carriers to ionization is shown to outweigh the opposing effects of dead space, increasing the avalanche speed of short avalanche photodiodes (APDs) over the predictions of a conventional local model which ignores both of these effects. The trends in the measured gain-bandwidth product of two short InAlAs APDs reported in the literature support this result. Relatively large speed benefits are predicted to result from further small reductions in the lengths of short multiplication regions.     

Evaluation of Atmospheric and Vacuum Residues Using Molecular Distillation and Optimization

The term atmospheric residue describes the material at the bottom of the atmospheric distillation tower having a lower boiling point limit of about 340°C; the term vacuum residue (heavy petroleum fractions) refers to the bottom of the vacuum distillation, which has an atmospheric equivalent boiling point (AEBP) above 540°C. In this work, the objective is to evaluate the behavior of different kinds of Brazilian atmospheric and vacuum residues using molecular distillation. The Falling Film Molecular Distillator was used. For the results obtained through this process, a significant range of temperature can be explored avoiding the thermal decomposition of the material. So these results are very important to the refinery decisions and improvements. The Experimental Factorial Design results showed that the temperature has more influence on the process than the feed flow rate, when a higher percentage of distillate is required.     

Optimised anaerobic treatment of house-sorted biodegradable waste and slaughterhouse waste in a high loaded half technical scale digester.

Anaerobic co-digestion of organic wastes from households, slaughterhouses and meat processing industries was optimised in a half technical scale plant. The plant was operated for 130 days using two different substrates under organic loading rates of 10 and 12 kgCOD.m(-3).d(-1). Since the substrates were rich in fat and protein components (TKN: 12 g.kg(-1) the treatment was challenging. The process was monitored on-line and in the laboratory. It was demonstrated that an intensive and stable co-digestion of partly hydrolysed organic waste and protein rich slaughterhouse waste can be achieved in the balance of inconsistent pH and buffering NH4-N. In the first experimental period the reduction of the substrate COD was almost complete in an overall stable process (COD reduction >82%). In the second period methane productivity increased, but certain intermediate products accumulated constantly. Process design options for a second digestion phase for advanced degradation were investigated. Potential causes for slow and reduced propionic and valeric acid degradation were assessed. Recommendations for full-scale process implementation can be made from the experimental results reported. The highly loaded and stable codigestion of these substrates may be a good technical and economic treatment alternative.     

High-performance self-aligned SiGeC HBT with selectively grown Si/sub 1-x-y/Ge/sub x/C/sub y/ base by UHV/CVD

Si/sub 1-x-y/Ge/sub x/C/sub y/ selective epitaxial growth (SEG) was performed by cold-wall, ultrahigh-vacuum chemical vapor deposition, and the effects of incorporating C on the crystallinity of Si/sub 1-x-y/Ge/sub x/C/sub y/ layers and the performance of a self-aligned SiGeC heterojunction bipolar transistor (HBT) were evaluated. A Si/sub 1-x-y/Ge/sub x/C/sub y/ layer with good crystallinity was obtained by optimizing the growth conditions. Device performance was significantly improved by incorporating C, as a result of applying Si/sub 1-x-y/Ge/sub x/C/sub y/ SEG to form the base of a self-aligned HBT. Fluctuations in device performance were suppressed by alleviating the lattice strain. Furthermore, since the B out diffusion could be suppressed by incorporating C, the cutoff frequency was able to be increased with almost the same base resistance. A maximum oscillation frequency of 174 GHz and an emitter coupled logic gate-delay time of 5.65 ps were obtained at a C content of 0.4%, which shows promise for future ultrahigh-speed communication systems.     

Preparation, patterning and luminescent properties of nanocrystalline Gd2O3:A (A=Eu, Dy, Sm, Er) phosphor films via Pechini sol–gel soft lithography

Nanocrystalline Gd₂O₃:A (A=Eu³⁺, Dy³⁺, Sm³⁺, Er³⁺) phosphor films and their patterning were fabricated by a Pechini sol–gel process combined with a soft lithography. X-ray diffraction (XRD), atomic force microscopy (AFM), scanning electron microscopy (SEM) and optical microscopy, UV/vis transmission and photoluminescence (PL) spectra as well as lifetimes were used to characterize the resulting films. The results of XRD indicated that the films began to crystallize at 500 °C and that the crystallinity increased with the elevation of annealing temperatures. Uniform and crack free non-patterned phosphor films were obtained by optimizing the composition of the coating sol, which mainly consisted of grains with an average size of 70 nm and a thickness of 550 nm. Using micro-molding in capillaries technique, we obtained homogeneous and defects-free patterned gel and crystalline phosphor films with different stripe widths (5, 10, 20 and 50 μm). Significant shrinkage (50%) was observed in the patterned films during the heat treatment process. The doped rare earth ions (A) showed their characteristic emission in crystalline Gd₂O₃ phosphor films due to an efficient energy transfer from Gd₂O₃ host to them. Both the lifetimes and PL intensity of the rare earth ions increased with increasing the annealing temperature from 500 to 900 °C, and the optimum concentrations for Eu³⁺, Dy³⁺, Sm³⁺, Er³⁺ were determined to be 5, 0.25, 1 and 1.5 mol% of Gd³⁺ in Gd₂O₃ films, respectively.     

Analysis of feedback for higher order polarization-mode dispersion mitigation of NRZ 40-Gb/s optical transmission

First-order polarization-mode dispersion (PMD) compensation by means of a polarization controller and a differential delay line is not sufficient to guarantee error-free transmission for 40-Gb/s channels when higher order effects severely increase signal distortion. Higher order mitigation is possible by cascading more than one first-order block. However, only two-stage or three-stage devices remain simple enough to be actually controlled. The performance of such higher order PMD compensators is evaluated by means of numerical simulations. Two different feedback signals have been used, demonstrating that first-order and higher order PMD distortion of nonreturn-to-zero (NRZ) pulses at 40 Gb/s can be strongly mitigated for instantaneous values of the differential group delay (DGD) up to the bit slot, when the compensator is properly controlled.