Disc filtration for separation of flocs from a moving bed bio-film reactor.

A Discfilter with 10 and 18 microm filter openings, respectively, was placed in parallel to a flotation plant for separation of biological flocs from a post-denitrifying Kaldnes Moving Bed Process, the last treatment step at the municipal wastewater treatment plant at Sj?unda, Malm?, Sweden. The effluent concentrations from the 10 and 18 microm filter were 2-5 and 2-8 mg SS L(-1), respectively, which is comparable to, or better than, the flotation plant. Comparison with experiences from activated sludge plants shows that the Discfilter works especially well after the Kaldnes process. Particle size distribution (PSD) studies show that particles larger than the filter openings of 10 and 18 microm are separated with approximately 90% efficiency, whereas most of the smaller particles pass the filter. This fact indicates that the major particle separation mechanism is physical blocking. These findings point to the possibility of improving the prediction of the separation efficiency by combining measurements of turbidity and suspended solids with particle size analysis.     

Hydrogen degradation of steels in gas mains after long periods of operation

We study the degradation of the mechanical and corrosion properties of 17G1S steel in gas mains as a result of operation for 28–40 yr. We reveal the simultaneous decrease in its strength and hardness, on the one hand, and impact toughness and crack resistance, on the other hand. The indicated parameters prove to be most sensitive to the in-service degradation of the metal. The degradation of steel leads to the increase in the strain-hardening coefficient and the appearance of the yield plateau in the tensile stress-strain diagram and causes the appearance of sensitivity to hydrogen embrittlement increasing in the process of operation. We analyze the role of absorbed hydrogen affecting the mechanism of strain aging and responsible for the appearance of defects. It is shown that the polarization resistance can be used not only for monitoring of the corrosion state of gas pipelines but also for the prediction of changes in their mechanical properties in the process of operation. __________ Translated from Fizyko-Khimichna Mekhanika Materialiv, Vol. 43, No. 5, pp. 97–104, September–October, 2007.     

Segregation band formation in Al-Si die castings

Banded defects are often found in high-pressure die castings. These bands can contain segregation, porosity, and/or tears, and changing casting conditions and alloy are known to change the position and make-up of the bands. Due to the complex, dynamic nature of the high-pressure die-casting (HPDC) process, it is very difficult to study the effect of individual parameters on band formation. In the work presented here, bands of segregation similar to those found in cold-chamber HPDC aluminum alloys were found in laboratory gravity die castings. Samples were cast with a range of fraction solids from 0 to 0.3 and the effect of die temperature and external solid fraction on segregation bands was investigated. The results are considered with reference to the rheological properties of the filling semisolid metal and a formation mechanism for bands is proposed by considering flow past a solidifying immobile wall layer.     

Threshold and growth mechanism of fatigue cracks under mode II and III loadings

ABSTRACT The fatigue crack growth behaviour of 0.47% carbon steel was studied under mode II and III loadings. Mode II fatigue crack growth tests were carried out using specially designed double cantilever (DC) type specimens in order to measure the mode II threshold stress intensity factor range, ΔK_IIth. The relationship ΔK_IIth > ΔK_Ith caused crack branching from mode II to I after a crack reached the mode II threshold. Torsion fatigue tests on circumferentially cracked specimens were carried out to study the mechanisms of both mode III crack growth and of the formation of the factory‐roof crack surface morphology. A change in microstructure occurred at a crack tip during crack growth in both mode II and mode III shear cracks. It is presumed that the crack growth mechanisms in mode II and in mode III are essentially the same. Detailed fractographic investigation showed that factory‐roofs were formed by crack branching into mode I. Crack branching started from small semi‐elliptical cracks nucleated by shear at the tip of the original circumferential crack.     

Combined time and wavelength multiplexing technique of optical fiber grating sensor arrays using commercial OTDR equipment

The use of a commercial optical time domain reflectometry device for simultaneous wavelength and time domain multiplexing of fiber-optic Bragg grating sensors is proposed and demonstrated. The realization of such systems provides an inexpensive way of interrogating several hundreds of sensors in a single fiber. Strain resolution of 30 /spl mu/m/m over a strain measuring range of 0.5% was obtained.     

One-dimensional diffuser based on a thick layer of dichromated gelatin

A new diffuser capable of scattering light in one direction (one-dimensional diffuser) has been developed and experimentally tested. The diffuser is formed in a thick layer of dichromated gelatin. The scattering indicatrices of the diffuser measured in two mutually perpendicular directions are presented. It is demonstrated that the indicatrix width in one direction is significantly greater than that in the perpendicular direc-tion. However, no zero-order diffraction has been observed. The proposed one-dimensional diffuser exhibits close scattering indicatrices for reading at a wavelength of 0.44 and 0.63 μm.     

Grain refinement of Al-7Si alloys and the efficiency assessment by recognition of cooling curves

Under sand cup solidification condition, the influence of Ti, B concentration, and holding time on the grain size of a high-purity Al-7Si alloy has been systematically studied. It is found that the grain size decreases rapidly at lower Ti or B additions, and is almost constant at the higher concentrations. For Al-3B refined Al-7Si alloys, the grain size increases at the initial period of holding time, and then rapidly becomes independent of holding time; while for Al-7Si alloys refined with Al-5Ti-1B, the grain size increases with holding time throughout. To evaluate the refinement efficiency, a new method named “intelligent evaluating of melt quality by pattern recognition of thermal analysis cooling curves” has also been introduced in this article. The results show that comparing the cooling curve of the evaluated melt with those in a database to find the most similar one to it can precisely assess the grain refinement efficiency of the measured Al-7Si alloy. In addition, the influence of Ti, B addition levels, and pouring temperatures on some characteristic parameters of cooling curve has also been discussed.     

Electrospray droplet sources for thin film deposition

Electrospraying utilises electrical forces for liquid atomisation. Droplets obtained by this method are highly charged to a fraction of the Rayleigh limit. The advantage of electrospraying is that the droplets can be extremely small, down to the order of 10’s nanometres, and the charge and size of the droplets can be controlled to some extent be electrical means. Motion of the charged droplets can be controlled by electric field. The deposition efficiency of the charged spray on an object is usually higher than that for uncharged droplets. Electrospray is, or potentially can be applied to many processes in industry and in scientific instruments manufacturing. The paper reviews electrospray methods and devices, including liquid metal ion sources, used for thin film deposition. This technique is applied in modern material technologies, microelectronics, micromachining, and nanotechnology.     

Static and pulsed pressures measured using electrically conducting rubbers

A method of measuring static and pulsed pressures using electrically conducting rubber sensors is proposed. The method is based on a change in the volume resistivity of a filled rubber under the action of external pressure. The pressure-induced change in resistance of the rubber sensor is proportional to the applied pressure and can be measured by a bridge circuit. Using this method, it is possible to evaluate the degree of homogeneity of the pressure distribution over a solid surface. This is achieved by distributing rubber sensors over the given surface.     

Understanding the role of impulsivity and externalizing psychopathology in alcohol abuse: Application of the UPPS Impulsive Behavior Scale.

The present study explores the relation among 4 personality traits associated with impulsive behavior and alcohol abuse. Personality traits were measured using the 4 subscales of the UPPS Impulsive Behavior Scale (UPPS: S. P. Whiteside & D. R. Lynam. 2001). The UPPS and measures of psychopathology were administered to clinical samples of alcohol abusers high in antisocial personality traits (AAPD), alcohol abusers low in antisocial personality traits (AA), and a control group (total N = 60). Separate analyses of variance indicated that AAPDs had significant elevations on all 4 UPPS scales, whereas the AAs and controls differed only on the Urgency subscale. However, when controlling for psychopathology, group differences on the UPPS scales disappeared. The results suggest that personality traits related to impulsive behavior are not directly related to alcohol abuse but rather are associated with the elevated levels of psychopathology found in a subtype of alcohol abusers. (PsycINFO Database Record (c) 2010 APA, all rights reserved)