Simultaneous handover scheme for IEEE 802.11 WLANs with IEEE 802.21 triggers

Handover performance in wireless networks is important, especially nowadays, when multimedia services are becoming increasingly available over the wireless devices. However, users expect uncompromised mobility when using the service. Thus, the support of multimedia services is not possible if handover is inefficient. At the same time it is clear that a strict separation between IP Layer and the Link Layer results in built-in sources of delay. The paper discusses the IEEE 802.11 and Mobile IPv4 handover performance in practical scenarios. We introduce a new simultaneous handover scheme with IEEE 802.21 triggers. In order to verify the handover performance, simulation experiments have been conducted, whose results are also presented and discussed.     

Microstructural stability and creep properties of die casting Mg–4Al–4RE magnesium alloy

The AE44 (Mg–4Al–4RE) alloy was prepared by a hot-chamber die casting method. The microstructure, microstructural stability and creep properties at 175 °C were investigated. The microstructure was analyzed by scanning electron microscopy (SEM), transmission electron microscopy (TEM), X-ray diffraction (XRD) and the Rietveld method. The results show that die cast AE44 magnesium alloy consists of α-Mg, Al₁₁RE₃, Al₂RE and Al_2.12RE_0.88 phases. The Al₁₁RE₃ phase is thermally stable at 175 °C whereas the metastable Al_2.12RE_0.88 phase undergoes a transition into the equilibrium Al₂RE phase. The alloy investigated is characterized by good creep properties at temperatures of 175 °C and 200 °C.     

Solution of heat and mass transfer in counterflow wet-cooling tower fills

Model of heat and mass transfer in wet cooling tower fills is presented. The model consist of a set of four 1D ODEs describing the mass and energy conservation and kinetics with boundary conditions prescribed on opposite sides of the computational domain. Shooting technique with self adaptive Runge–Kutta step control is applied to solve the resulting model equations. The developed model is designed to be included in a large scale CFD calculations of a natural draft cooling tower where the fill is treated as a porous medium with prescribed distributions of mass and heat sources. Thus, the technique yields the spatial distributions of all flow parameters, specifically the heat and mass sources. Such distributions are not directly available in standard techniques such as Merkel, Poppe and e-NTU models of the fill where the temperature of the water is used as an independent variable. The method is validated against benchmark data available in the literature.     

Dynamic Combinatorial Chemistry in Chemical Catalysis

Despite the progress in the field of dynamic combinatorial chemistry (DCC), dynamic combinatorial catalysis has received considerably less attention. Some first studies, however, have provided proof of principle and demonstrated that DCC-based approaches are also applicable in catalyst development. This provides interesting new tools that are complementary to rational catalyst design and traditional combinatorial strategies. As such, DCC may become highly valuable in the field of dynamic combinatorial catalysis, due also to the practical importance of catalysis. In this review we focus on the principles of dynamic combinatorial catalysis and provide an overview by the introduction of different concepts related to the development of libraries and selection procedures in catalysis.     

Investigation of the cold orbital forging process of an AlMgSi alloy bevel gear

Orbital forging is a metal forming process in which one of the dies performs a complex rocking motion. It ensures reduction in required load and allows for the cold forming of a workpiece. One of the mechanical parts formed by means of this technology is a bevel gear. However, a numerical analysis of orbital forging bevel gears is very difficult to perform due to the complex rocking motion of the die, which is confirmed by numerous works investigating the orbital forging process. In the present work, investigation results of the cold orbital forging of aluminum alloy bevel gears are presented. In contrast to other works devoted to the process, this study proposes a new procedure for forming bevel gears and the workpiece used has a shape which is different from the previously applied ones. The obtained results apply to both theoretical and technological aspects of orbital forging. The FEM simulation results have been successfully verified in laboratory conditions using the industrial PXW-100A press.     

Identification of Mg<Subscript>2</Subscript>Cu particles in Cu-alloyed austempered ductile iron

In the present work, the Mg₂Cu precipitates in copper-alloyed austempered ductile iron (ADI) were identified by analyzing techniques such as TEM and SEM with EDS. It was revealed that, in castings made of ADI-containing copper, highly dispersed particles of Mg₂Cu are formed, whose size does not exceed <1 μm. The research work was carried out on ductile iron that was austenitized at 900 °C, followed by austempering at 380 °C. The microstructure was investigated using various techniques, including optical microscopy, XRD, SEM, and TEM. In addition to this, the exhibited impact properties of castings with Cu, Ni, and Cu+Ni were also determined. This study casts a new light on the formation of the structure of Cu-alloyed ADI. The highly-dispersive and brittle Mg₂Cu particles that are located in the vicinity of the graphite nodules have a negative effect on the impact properties of ADI. It has also been shown that impact strength decreases from levels of 160-180 J (for copper-free ADI) to 90-120 J (for copper-and copper-nickel-alloyed ADI).     

Nano-Mechanical Properties of Modified Poly(Methyl Methacrylate) Films Studied by Atomic Force Microscopy

Atomic force microscopy (AFM) has been used to study the effect of various photoinitiators doped into poly(methyl methacrylate) (PMMA) on the mechanical properties of PMMA films at the nanometer scale. Pure and modified PMMA films (containing four different photoinitiators) were exposed to a mercury vapor lamp in air atmosphere. Force–distance curves for hardness, Young modulus, and adhesion forces were obtained using different AFM modes (tapping or contact-mode) and different tips (diamond or silicon nitride). The results revealed that the added photoinitiators slightly changed the nanomechanical properties of PMMA as a result of alterations in the photochemical reactions and physical processes occurring in the studied systems. tert-Butyl peroxybenzoate had the most efficient effect on the measured parameters in UV-irradiated PMMA, whereas benzoyl peroxide was less active. The mechanism of the observed processes is discussed.     

XPS studies of perovskites surface instability caused by Ar+ ion and electron bombardment and metal deposition

X-ray Photoelectron Spectroscopy (XPS) was used to study the influence of low energy Ar⁺ ion bombardment, electron bombardment and Pt deposition on the SrTiO₃ (STO) single crystal electronic structure. Atomic composition changes were found and attributed to chemical reconstruction of the STO surface. A clear correlation between the presence of conducting, low Ti oxidation states in valence band and core level changes was detected. A strong effect caused by electron irradiation was ascribed to the electroreduction process. The influence of lanthanum doping on surface instability of STO was also discussed. The La doped sample (STO: 3,75% La) was found to be modified upon Pt metal deposition to a higher degree than pure STO crystal.     

Colony-blot assay with anti-p60 antibodies as a method for quick identification of Listeria in food

The present study evaluated the ability to isolate Listeria from foods, using shortened procedure of sample enrichment followed by immunomagnetic separation or filtration methods, and serological identification of isolated bacteria by colony-blot and Western blot methods with anti-p60 antibodies. By these rapid methods, identification of Listeria was achieved in much shorter time (40-48 h) than with standard cultivation and biochemical identification procedures. The rapid methods used are easy to perform and, what is most important, their specificity is very high and fulfills the expectations. The possibility to select Listeria colonies growing on non-selective media by blotting with anti-p60 antiserum seems to be particularly valuable in examination of food samples containing/not too many Listeria (1-10 CFU/25 g). However, the blot method using anti-PepD mAb specific to unique region of L. monocytogenes p60 is necessary to distinguish L. monocytogenes from other Listeria species.