Oil‐spill cleanup: The influence of acetylated curaua fibers on the oil‐removal capability of magnetic composites

A magnetic resin based on cardanol, furfural, and curaua fibers was prepared and characterized. The material could be used in oil‐spill cleanup processes, because of its aromatic/aliphatic balance. The resin was prepared through bulk polycondensation of cardanol and furfural in the presence of curaua fibers and maghemite nanoparticles. Hydrophobicity of the curaua fibers was improved by acetylation, increasing the oil‐absorbing capability of the composites. The obtained magnetic composites were studied by Fourier‐transform infrared spectroscopy, X‐ray diffraction, and thermogravimetric analysis. Degree of cure, magnetic force, and oil‐removal capability tests were also performed. The results show that the composites possess an elevated cure degree in addition to a considerable magnetic force. The materials exhibit a good oil removal capability in the presence of a magnetic field, which is improved by the use of acetylated curaua. In the best case, the composite filled with maghemite and curaua can remove 12 parts of oil from water. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41732.     

Experimental study on the solvent regeneration of a CO2‐loaded MEA solution using single and hybrid solid acid catalysts

The performance of a hybrid solid acid catalyst consisting of a physical mixture of γ‐Al₂O₃ and H‐ZSM‐5 in terms of the rate and heat duty for solvent regeneration (i.e., CO₂ stripping) of a CO₂‐rich MEA solution was compared with the individual performance of γ‐Al₂O₃, H‐ZSM‐5, and H‐Y solid acid catalysts using MEA (2–7 mol/L), with initial CO₂ loading of 0.5 mol CO₂/mol MEA at 378 K. It was observed that any catalyst significantly decreased the energy required for CO₂ regeneration. The performance of the catalysts investigated ranked as follows: γ‐Al₂O₃/H‐ZSM‐5 = 2/1 > γ‐Al₂O₃ > H‐ZSM‐5 > H‐Y if the process is in the lean CO₂ loading region whereas it was H‐ZSM‐5 > γ‐Al₂O₃/H‐ZSM‐5 = 2/1 > γ‐Al₂O₃ > H‐Y if the process is in the rich CO₂ loading region. These results highlight the joint dependence on Brønsted/Lewis acidity and mesopore surface area of heat duty for solvent regeneration. © 2015 American Institute of Chemical Engineers AIChE J, 62: 753–765, 2016     

Boron removal from water and its recovery using iron (Fe) oxide/hydroxide-based nanoparticles (NanoFe) and NanoFe-impregnated granular activated carbon as adsorbent

This study presents information obtained by the synthesis of Fe(3) oxide/hydroxide nanoparticles sol (NanoFe) and NanoFe-impregnated granular activated carbon as adsorbents for boron removal from solutions. The research describes an adsorption method for cleaning a solution containing boron contaminants followed by recovery of the adsorbent and the adsorbed material for safe removal or further reuse. The technology provides an efficient method of boron removal from water. A marked effect of NanoFe and NanoFe-impregnated GAC adsorbents concentration and pH level on boron removal efficiency was demonstrated. At least 95–98% boron recovery efficiency is possible using NanoFe sol and Fe-impregnated GAC that in fact also recover the adsorbent for reuse. Boron adsorption onto the NanoFe-impregnated GAC adsorbent may be described by pseudo-second-order reaction kinetics and the Langmuir isotherm model. The boron adsorption capacity on iron (3) oxide nanoparticles and Fe-impregnated GAC at an equilibrium concentration of 0.3 mg/dm³ as B in the solution is much higher than these values for similar adsorbents reported in the literature.     

Analysis of the Shrinkage Effect on Mass Transfer During Convective Drying of Sawdust/Sludge Mixtures

Convective drying of wastewater sludges and sawdust/sludge mixtures was studied. The first part of this work was an experimental study performed in a cross-flow convective dryer using 500 g of wet material extruded through a disk with circular dies of 12 mm. The results showed that the sawdust addition has a positive impact on the drying process from a mass ratio of 2/8, on a dry basis, with observed drying rates higher than the original sludge. The second part of this work consisted of developing a drying model in order to identify the internal diffusion coefficient and convective mass transfer coefficient from the experimental data. A comparison was made between fitted drying curves, well represented by the Newton's model, and the analytical solutions of the diffusion equation applied to a finite cylinder. Variations of dimensional characteristics, such as the volume and exchange surface of the sample bed, were obtained by X-ray tomography. This technique allowed us to confirm that shrinkage, which is an important phenomenon occurring during sludge and sawdust/sludge mixture drying, must be taken into account. The results showed that both the internal diffusion coefficient and convective mass transfer coefficient were affected by mixing and sawdust addition. The internal diffusion coefficient changed from 7.77 × 10^?9 m²/s for the original sludge to 7.01 × 10^?9 m²/s for the mixed sludge and then increased to 8.35 × 10^?9 m²/s for the mixture of a mass ratio of 4/6. The convective mass transfer coefficient changed from 9.70 × 10^?8 m/s for the original sludge to 8.67 × 10^?8 m/s for the mixed sludge and then increased to 12.09 × 10^?8 m/s for the mixture of a mass ratio of 4/6. These results confirmed that sawdust addition was beneficial to the sludge drying process as the mass transfer efficiency between the air and material increased. Reinforcing the texture of sludge by adding sawdust can increase the drying rate and decrease the drying time, and then the heat energy supply will be reduced significantly. The study also showed that neglecting shrinkage phenomenon resulted in an overestimation for the internal diffusion coefficient for the convective drying of sludges and sawdust/sludge mixtures.     

Microstructure and mechanical properties of Al2O3/ZrO2 composites by two-step sintering

Composites of Al₂O₃/ZrO₂ (containing 25, 50, and 75 vol% ZrO₂) were prepared by mixing Al₂O₃ and ZrO₂ suspensions. The microstructural control via two-step sintering (TSS) was the main objective of this work. For this purpose, different sintering curves were constructed, aiming to achieve the best temperature combination for the sintering steps that provides higher density and finer microstructure. The results were compared with single-step sintering (SSS). Furthermore, microhardness and fracture toughness were measured for the best TSS specimens under each composition. The results showed that the high densities were obtained, and the reduction of grain size was greater than 40% for two-step sintered specimens, compared to SSS ones. Consequently, microhardness values increased. However, fracture toughness values remained unchanged.     

Elucidation of the formation of CO2 in culinary dry products

 The formation of CO₂ in tomato powder, chosen as an example of a dry culinary product, was investigated at room temperature and at low values of water activity (a _w). CO₂ formation correlated well with parameters that represent the beginning and progression of the Maillard reaction. In the absence of O₂, CO₂ formation decreased. Pectin and depolymerized pectin did not influence CO₂ formation while galacturonic acid (GalA) had a large effect. Determination of ¹³CO₂ in low-moisture model systems revealed that CO₂ was not formed by decarboxylation of GalA alone. Only a small proportion of [1-¹³C]glycine and GalA was degraded by the Strecker pathway; however, glucose reacted with the labelled amino acid forming ¹³CO₂ which amounted to over 90% of the total CO₂ formed. Therefore, CO₂ could be used as an early indicator for the beginning of the Maillard reaction in dry culinary products. Received: 28 October 1996     

Investigation mechanism of DEA as an activator on aqueous MEA solution for postcombustion CO2 capture

In this work, Diethanolamine (DEA) was considered as an activator to enhance the CO₂ capture performance of Monoethanolamine (MEA). The addition of DEA into MEA system was expected to improve disadvantages of MEA on regeneration heat, degradation, and corrosivity. To understand the reaction mechanism of blended MEA‐DEA solvent and CO₂, ¹³C nuclear magnetic resonance (NMR) technique was used to study the ions (MEACOO^‐, DEACOO^–, MEA, DEA, MEAH⁺, DEAH⁺, , ) speciation in the blended MEA‐DEA‐CO₂‐H₂O systems with CO₂ loading range from 0 to 0.7 mol CO₂/mol amine at the temperature of 301 K. The different ratios of MEA and DEA (MEA: DEA = 2.0:0, 1.5:0.5, 1.0:1.0, and 0:2.0) were studied to comprehensively investigate the role of DEA in the system of MEA‐DEA‐CO₂‐H₂O. The results revealed that DEA performs the coordinative role at the low CO₂ loading and the competitive role at high CO₂ loading. Additionally, the mechanism was also proposed to interpret the reaction process of the blended solvent with CO₂. © 2018 American Institute of Chemical Engineers AIChE J, 64: 2515–2525, 2018     

Site‐Selectively Coated,Densely‐Packed Microprojection Array Patches for Targeted Delivery of Vaccines to Skin

Densely packed dry‐coated microprojections are shown to deliver vaccines to targeted locations within the skin that are rich in immune cells, thus inducing protective immune responses against a lethal virus challenge. Selectively limiting the antigen coating to the tips of the projections, which penetrate the skin, would significantly reduce the amount of vaccine required in immunization. In this paper a simple technique, dip‐coating the microprojections, is introduced to meet this goal. By increasing the coating solution viscosity, an otherwise strong capillary action is mitigated and the desired controlled coating length on projections is achieved. Following application to the skin, most of the coated vaccine material is rapidly released from the projections (82.6% in mass within 2 min) to the target locations within the skin strata and a potent immune response is induced when a conventional influenza vaccine (Fluvax) is tested in a mouse model. The utility of this coating approach to a variety of molecules representative of vaccines (e.g., chicken egg ovalbumin (OVA) protein, DNA, and fluorescent dyes) is demonstrated. These collective attributes, together with the simplicity of the approach, position the dip‐coating method for practical utility in large vaccination campaigns.     

The effect of changes in nitrate concentration in drinking water on methemoglobin levels in infants

For a five‐day period infants consuming powdered milk formula made up with tap water were exposed to water of controlled nitrate content. There was a significant rise in MetHb levels above normal in most children after the first day of exposure to high nitrate water (108 mg/1 NO3). This was followed by some indication of a drop in MetHb levels despite the continued exposure and finally a return to normal levels when the exposure to nitrates stopped. No clinical signs of methemoglobinemia developed. The possible existence of an adaption mechanism is suggested but requires further elucidation.     

Electrochemical characterization of electrolytes for lithium-ion batteries based on lithium difluoromono(oxalato)borate

The salt lithium difluoromono(oxalato)borate (LiDFOB) showed some promising results for lithium-ion-cells. It was synthesized via a new synthetic route that avoids chloride impurities. Here we report the properties of its solutions (solvent blend ethylene carbonate/diethyl carbonate (3:7, mass ratio), including its conductivity, cationic transference number, hydrolysis, Al-current collector corrosion-protection ability and its cycling performance with some electrode materials. Some Al-corrosion studies were also performed with the help of our recently developed computer controlled impedance scanning electrochemical quartz crystal microbalance (EQCM) that proofed to be a useful tool for battery material investigations.