Aerobic Oxidation of Alcohols Catalyzed by Copper Nanoparticle-Polyacrylamide/SBA-15 as Novel Polymer-Inorganic Hybrid

Heterogeneous hybrid polymer-inorganic copper nanoparticle-polyacrylamide/SBA-15 was prepared, characterized and tested as a catalyst for efficiently selective oxidation of alcohols to aldehydes in high yields under molecular oxygen in n-hexane solvent. The catalyst can be recycled over six-times without significant loss of activity.     

Hydrogen generation from the ball milled composites of sodium and lithium borohydride (NaBH4/LiBH4) and magnesium hydroxide (Mg(OH)2) without and with the nanometric nickel (Ni) additive

The composites of (NaBH₄+2Mg(OH)₂) and (LiBH₄+2Mg(OH)₂) without and with nanometric Ni (n-Ni) added as a potential catalyst were synthesized by high energy ball milling. The ball milled NaBH₄-based composite desorbs hydrogen in one exothermic reaction in contrast to its LiBH₄-based counterpart which dehydrogenates in two reactions: an exothermic and endothermic. The NaBH₄-based composite starts desorbing hydrogen at 240 °C. Its ball milled LiBH₄-based counterpart starts desorbing at 200 °C. The latter initially desorbs hydrogen rapidly but then the rate of desorption suddenly decelerates. The estimated apparent activation energy for the NaBH₄-based composite without and with n-Ni is equal to 152 ± 2.2 and 157 ± 0.9 kJ/mol, respectively. In contrast, the apparent activation energy for the initial rapid dehydrogenation for the LiBH₄-based composite is very low being equal to 47 ± 2 and 38 ± 9 kJ/mol for the composite without and with the n-Ni additive, respectively. XRD phase studies after volumetric isothermal dehydrogenation tests show the presence of NaBO₂ and MgO for the NaBH₄-based composite. For the LiBH₄-based composite phases such as MgO, Li₃BO₃, MgB₂, MgB₆ are the products of the first exothermic reaction which has a theoretical H₂ capacity of 8.1 wt.%. However, for reasons which are not quite clear, the first reaction never goes to full completion even at 300 °C desorbing ∼4.5 wt.% H₂ at this temperature. The products of the second endothermic reaction for the LiBH₄-based composite are MgO, MgB₆, B and LiMgBO₃ and the reaction has a theoretical H₂ capacity of 2.26 wt.%. The effect of the addition of 5 wt.% nanometric Ni on the dehydrogenation behavior of both the NaBH₄-and LiBH₄-based composites is rather negligible. The n-Ni additive may not be the optimal catalyst for these hydride composite systems although more tests are required since only one n-Ni content was examined.     

Synthesis of TiC–Al2O3 nanocomposite powder from impure Ti chips, Al and carbon black by mechanical alloying

The possibility of providing TiC–Al₂O₃ nanocomposite as a useful composite from low-cost raw materials has been investigated. Impure Ti chips were placed in a high energy ball mill with carbon black and aluminum powder and sampled after different times. XRD analysis showed that TiC has been synthesized after 10 h of milling. It could be observed from the width of XRD patterns’ peaks that the size of produced TiC crystallites is in the order of nanometer. In order to forming of TiC–Al₂O₃ composite, heat treatment was performed in different temperatures. Investigations have revealed that formation temperature of TiC as the dominant phase decreased for the milled specimens during heat treatment, also nanocrystalline TiC–Al₂O₃ composite was formed in this situation. Furthermore milling led to increase of strain and decrease of TiC lattice parameter while during heat treatment nanocrystalline grains grow up and strain decreases.     

Modeling and numerical simulation of solar chimney power plants

The solar chimney power plant is a simple solar thermal power plant that is capable of converting solar energy into thermal energy in the solar collector. In the second stage, the generated thermal energy is converted into kinetic energy in the chimney and ultimately into electric energy using a combination of a wind turbine and a generator. The purpose of this study is to conduct a more detailed numerical analysis of a solar chimney power plant. A mathematical model based on the Navier-Stokes, continuity and energy equations was developed to describe the solar chimney power plant mechanism in detail. Two different numerical simulations were performed for the geometry of the prototype in Manzanares, Spain. First, the governing equations were solved numerically using an iterative technique. Then, the numerical simulation was performed using the CFD software FLUENT that can simulate a two-dimensional axisymmetric model of a solar chimney power plant with the standard k-epsilon turbulence model. Both the predictions were compared with the available experimental data to assess the validity of the model. The temperature, velocity and pressure distributions in the solar collector are illustrated for three different solar radiations. Reasonably good quantitative agreement was obtained between the experimental data of the Manzanares prototype and both the numerical results.     

Response Analysis of Field-Scale Fully Grouted Standard Cable Bolts Using a Coupled ANN–FDM Approach

This paper presents a coupled approach using an artificial neural network (ANN) and the finite difference method (FDM) that has been developed to predict the distribution of axial load along fully grouted standard cable bolts in the field using laboratory pullout test data. A back-propagation training algorithm was used in ANN to determine axial loads in the cables tested in the laboratory. The ANN component of the computational model was trained using two different types of data sets. At first, the ANN was trained to predict the axial loads in a series of short cables grouted with Portland cement at a specific water-to-cement ratio and subjected to different radial confining stiffness values. Next, the ANN model was trained for an expanded case to include the influence of lateral confining stress on the distribution of axial load in the cable reinforcement. Finally, the ANN model was implemented into a widely used, FDM-based geotechnical software (FLAC). The accuracy of the ANN–FDM model is demonstrated in this paper against measured data from laboratory and field tests. The analysis approach introduced in this study is a valuable computational tool that can be used to determine the axial load distribution in long standard cable bolts, which are commonly installed to stabilize rock masses in various geotechnical, transportation, and mining applications.     

Waterproof AlInGaP optoelectronics on stretchable substrates with applications in biomedicine and robotics

Inorganic light-emitting diodes and photodetectors represent important, established technologies for solid-state lighting, digital imaging and many other applications. Eliminating mechanical and geometrical design constraints imposed by the supporting semiconductor wafers can enable alternative uses in areas such as biomedicine and robotics. Here we describe systems that consist of arrays of interconnected, ultrathin inorganic light-emitting diodes and photodetectors configured in mechanically optimized layouts on unusual substrates. Light-emitting sutures, implantable sheets and illuminated plasmonic crystals that are compatible with complete immersion in biofluids illustrate the suitability of these technologies for use in biomedicine. Waterproof optical-proximity-sensor tapes capable of conformal integration on curved surfaces of gloves and thin, refractive-index monitors wrapped on tubing for intravenous delivery systems demonstrate possibilities in robotics and clinical medicine. These and related systems may create important, unconventional opportunities for optoelectronic devices.     

Effects of fiber ellipticity and orientation on dynamic stress concentrations in porous fiber-reinforced composites

Interaction of time harmonic fast longitudinal and shear incident plane waves with an elliptical fiber embedded in a porous elastic matrix is studied. The novel features of Biot dynamic theory of poroelasticity along with the classical method of eigen-function expansion and the pertinent boundary conditions are employed to develop a closed form series solution involving Mathieu and modified Mathieu functions of complex arguments. The complications arising due to the non-orthogonality of angular Mathieu functions corresponding to distinct wave numbers in addition to the problems associated with appearance of additional angular dependent terms in the boundary conditions are all avoided by expansion of the angular Mathieu functions in terms of transcendental functions and subsequent integration, leading to a linear set of independent equations in terms of the unknown scattering coefficients. A MATHEMATICA code is developed for computing the Mathieu functions in terms of complex Fourier coefficients which are themselves calculated by numerically solving appropriate sets of eigen-systems. The analytical results are illustrated with numerical examples in which an elastic fiber of elliptic cross section is insonified by a plane fast compressional or shear wave at normal incidence. The effects of fiber cross sectional ellipticity, angle of incidence (fiber two-dimensional orientation), and incident wave polarization (P, SV, SH) on dynamic stress concentrations are studied in a relatively wide frequency range. Limiting cases are considered and fair agreements with well-known solutions are established.     

Development of smoothed particle hydrodynamics method for modeling active nematics

This article proposes a novel graphics processing unit-based active nematic flow solver based on the smoothed particle hydrodynamics (SPH) method. Nematohydrodynamics equations are discretized using the SPH algorithm. Flow behavior, nematic ordering, topological defects, and vorticity correlation are calculated and discussed in detail. The spectrum of the kinetic energy with respect to the wavenumber is calculated at high particle resolution, and its slope at the different length scales is discussed. To exploit the SPH capabilities, pathlines of nematic particles are evaluated during the simulation. Finally, the mixing behavior of the active nematics is calculated as well and described qualitatively. The effects of two important parameters, namely, activity and elastic constant are investigated. It is shown that the activity intensifies the chaotic mixing nature of the active nematics, while the elastic constant behaves oppositely.     

Synthesis,characterization and catalytic activity studies of Pd-based supported nanoparticle catalyst anchoring on poly(N-vinyl-2-pyrrolidone) modified CMK-3

Pd nanoparticle-poly(N-vinyl-2-pyrrolidone)/CMK-3 (Pd-PVP/CMK-3) composite was prepared by in situ polymerization method which was effectively employed as a novel heterogeneous catalyst for the Suzuki–Miyaura cross-coupling reaction. The physical and chemical properties of Pd nanoparticle-PVP/CMK-3 were investigated using FT-IR, XRD, BET, UV–vis, TEM and TGA techniques. The reaction was carried out between aryl halides and phenylboronic acid in the presence of water at room temperature. The stability of the catalyst was good and could be reused 10 times without much loss of activity in Suzuki–Miyaura reaction.