ESD–RF co-design methodology for the state of the art RF-CMOS blocks

This paper describes an approach to design ESD protection for integrated low noise amplifier (LNA) circuits used in narrowband transceiver front-ends. The RF constraints on the implementation of ESD protection devices are relaxed by co-designing the RF and the ESD blocks, considering them as one single circuit to optimise. The method is applied for the design of 0.25 μm CMOS LNA. Circuit protection levels higher than 3 kV HBM stress are achieved using conventional highly capacitive ggNMOS snapback devices. The methodology can be extended to other RF-CMOS circuits requiring ESD protection by merging the ESD devices in the functionality of the corresponding matching blocks.     

Fluidized bed heat treatment of cast Al-Si-Cu-Mg alloys

The effects of fluidized bed heat treatment on the microstructural and mechanical properties of Al-Si-Cu-Mg cast alloys, namely, 354 and 319, were studied. The heating rate in fluidized beds (FBs) is greatervis-à-vis conventional electrical resistance furnaces (CFs). The high heating rate in FBs increases the kinetics of metallurgical phenomena such as Si fragmentation and spherodization during solution heat treatment, as well as the precipitation rate of phases such as Al₅Cu₂Mg₈Si₆ and Al₂Cu during aging. It is observed that the dissolution rate of phases such as Mg₂Si and Al₅Cu₂Mg₈Si₆ takes place very rapidly. The solution heat treatment of 319 alloy using FB results in complete dissolution of Mg₂Si and Al₅Cu₂Mg₈Si₆ particles within 45 minutes. However, for phases such as Al₂Cu and Ferich intermetallics, the dissolution rate is relatively slow. Even on prolonged solution heat treatment for 6 hours, these phases do not dissolve completely. It is observed that incomplete dissolution of the Al₂Cu phase does not significantly affect tensile properties of T4-treated alloys. The optimum solution heat-treatment time in FB for both 354 and 319 alloys is 45 minutes at 527 °C and 493 °C, respectively. Thermal analysis shows an exothermic peak owing to recrystallization and coarsening of eutectic grains during solution heat treatment. The high heating rate in FB causes this transformation to take place at a lower temperature than in CF. It is observed that the nucleation rate of Al₅Cu₂Mg₈Si₆ during aging in FB is greater than using CF. Thermal analysis of samples during the ramp-up stage while aging using FB did not show any phase transformation, while those using CF show two endothermic transformations, which are most likely due to the dissolution of GP zones or the co-cluster of solutes. Aging at 200 °C results in a greater number density of precipitates than those at 240 °C. The tensile strength of samples aged at 200 °C is greater than those aged at 240 °C, because the amount of precipitates formed at 200 °C is greater than that at 240 °C. The total heat-treatment time for T6 temper is less than 2 hours in FBs, which is a significant reduction in heat-treatment time, as well as energy consumption.     

Formation of ordered metal nanowire-inorganic salt composites

A new phenomenon accompanying the electrolysis of salts has been observed, whereby an ordered composite is formed under certain conditions (electrolyte composition, current density). The composite comprises an inorganic salt crystal penetrated by metal nano- and microwires. This phenomenon can serve as a basis for the technology of oriented and ordered nanowire array synthesis.     

A framework of virtual prototyping environment for the design and analysis of mechanical mechanism with clearance

Mechanical mechanisms with clearance abound in technological fields such as robotics, machine and steam turbine industry. The dynamic performance of these mechanisms in working condition can be achieved provided that the effects of the different on the mechanisms (such as mechanism dynamics, technological effects and thermal behaviour) are thoroughly understood. Virtual prototyping provides an integration of multi-domain dynamic simulation for the design and analysis process. In the current paper, a framework of virtual prototyping environment for the design and analysis of mechanical mechanism with clearance is presented. A case study with such a simulation strategy is studied for the optimum design and analysis of the technological parameter.     

On the possibility of development of defects in zirconium parts of thermal reactors during storage prior to and after operation

We have established that technological defects (cracks) in zirconium articles can develop in the course of long-term storage prior to their mounting in a reactor, which is caused by the action of residual stresses and hydrogen. We have considered the conditions of after-operation storage of zirconium articles of the fuel core of thermal reactors in water of the cooling ponds of reactors and in spent-fuel storehouses. The possibility of subsequent hydrogenation of these articles during their storage has been shown. Finally, we have studied the effect of hydrogen, absorbed in the course of storage, on the crack resistance of zirconium articles and the development of defects in them due to delayed hydride cracking. __________ Translated from Fizyko-Khimichna Mekhanika Materialiv, Vol. 43, No. 5, pp. 105–109, September–October, 2007.     

Next-day electricity-price forecasting using a hybrid network

The paper proposes a novel method of forecasting short-term electricity price based on a two-stage hybrid network of self-organised map (SOM) and support-vector machine (SVM). In the first stage, a SOM network is applied to cluster the input-data set into several subsets in an unsupervised manner. Then, a group of SVMs is used to fit the training data of each subset in the second stage in a supervised way. With the trained network, one can predict straightforwardly the next-day hourly electricity prices. To confirm its effectiveness, the proposed model has been trained and tested on the data of historical energy prices from the New England electricity market.     

Amorphous diffusion bonding of steel pipe and its impact toughness

An iron-based amorphous foil (FeNiCrSiB) was used as an interlayer for the amorphous diffusion bonding of low carbon steel pipes under argon flux. The microstructure and mechanical properties of the joint were analyzed using an electron probe micro-analyzer (EPMA), tensile test, bending test and impact test. The results show that the joint microstructure resembles that of the base metal and no precipitates form at the joint. Melting point depressants (B, Si) diffuse far away from the joint and the base metal element is homogenous across the joint. The joint impact toughness is greater than the base metal toughness and the mechanical properties of the joint are similar around the pipe.     

Deposition of thin film silicon using the pulsed PECVD and HWCVD techniques

We report on the use of pulsed plasma-enhanced chemical vapor deposition (P-PECVD) technique and show that “state-of-the-art” amorphous silicon (a-Si:H) materials and solar cells can be produced at a deposition rate of up to 15 Å/s using a modulation frequency in the range 1–100 kHz. The approach has also been developed to deposit materials and devices onto large area, 30 cm×40 cm, substrates with thickness uniformity (<5%), and gas utilization rate (>25%). We have developed a new “hot wire” chemical vapor deposition (HWCVD) method and report that our new filament material, graphite, has so far shown no appreciable degradation even after deposition of 500 μm of amorphous silicon. We report that this technique can produce “state-of-the-art” a-Si:H and that a solar cell of p/i/n configuration exhibited an initial efficiency approaching 9%. The use of microcrystalline silicon (μc-Si) materials to produce low-cost stable solar cells is gaining considerable attention. We show that both of these techniques can produce thin film μc-Si, dependent on process conditions, with 1 1 1 and/or 2 2 0 orientations and with a grain size of approx. 500 A. Inclusion of these types of materials into a solar cell configuration will be discussed.     

Impact of a snow avalanche against an obstacle. Formation of shock waves

The paper is devoted to the effect of compressibility of the avalanche snow impacting an obstacle. Compression shocks generated by obstacle cause high pressure peaks at first instants of impact. That is why the account of compressibility is essential for the understanding of measurements and the design of structures. The main problem in calculation compression shocks in avalanches is to formulate an equation of state for moving snow in impact. Two different types of equations of state are proposed depending on the type of the avalanche (low-density and high-density flows). The approach is not totally new. It was earlier proposed mainly in Russian literature. Here a brief review of the previous work is given with discussion of some gaps in it. The theory is reformulated and further developed to account thermodynamical equations. The simplest case of a normal compression shock in an avalanche flow is studied. Examples of estimations of pressure and density behind a shock are given. It is important to emphasize that the Mach number plays an important role in the theory of compressible flows so it should be taken into account (together with the Froude number) in calculation and modelling an avalanche impact pressure.     

Formation of layered structure on bismuth-borate glass surface

X-ray diffraction analysis shows that the transformation during heat treatment from amorphous to crystalline phases of bismuth-borate glass samples takes place in sequences. After a short heat treatment, 5 min at 550 °C, a layered structure with a preferred orientation of crystallites on the surface is observed. After a long heat treatment, 8 h at the same temperature, normal polycrystalline bulk samples are obtained.