94-GHz propagation in the evaporation duct

One-way, low-altitude radio propagation measurements at 94 GHz and simultaneous surface meteorological measurements were made on a 40.6 km, over-horizon, over-water path along the southern California coast to assess the effects of the evaporation duct on signal propagation. More than 2000 h of RF and meteorological data were recorded in eight measurement periods from July 1986 to July 1987. On this path, the transmission loss in a standard atmosphere is nearly 280 dB; the median transmission loss measured is approximately 220 dB. This significant decrease in loss is due to the evaporation duct. A propagation model is used to predict transmission loss from observed surface meteorology; predictions derived from 10-min averages of wind speed, air temperatures, sea temperature, and humidity compare favorably to the measured values. On average, the modeling underestimates observations by only 10 dB. The propagation model is used to predict transmission loss from an independent climatology of evaporation duct heights. A comparison of the modeled distribution to the observed distribution is favorable. The accuracy of the propagation model provides a strong justification for using it to assess the propagation characteristics of millimeter-wave communication and radar systems operating in many, if not all, ocean regions     

Propagation along a two-wire line located at the air-Earthinterface

A simple quasi-static expression for the propagation constant of a two-wire transmission line located at the air-Earth interface is derived. A numerical solution of the mode equation shows that the quasi-static approximation is valid when the wire separation is much less than a free-space wavelength. The quasi-static approximation can be used to determine the complex dielectric constant of the Earth from measurements of either the propagation constant or the characteristic impedance of the transmission line     

MESFET MMIC Ka-band transmitter performance forhigh-volume system applications

An MMIC transmitter for high-volume smart munition applications in Ka band is developed using 0.25 μm MESFET technology. The transmitter, consisting of a voltage-controlled oscillator (VCO) and power amplifier (PA), delivers more than 100 mW of power with an overall efficiency of 10% and a linear tuning range of more than 700 MHz around 35 GHz     

Enhancing the multivariate signal of [15O] water PETstudies with a new nonlinear neuroanatomical registration algorithm [MRIapplication]

This paper addresses the problem of neuro-anatomical registration across individuals for functional [15O] water PET activation studies. A new algorithm for three-dimensional (3-D) nonlinear structural registration (warping) of MR scans is presented. The method performs a hierarchically scaled search for a displacement field, maximizing one of several voxel similarity measures derived from the two-dimensional (2-D) histogram of matched image intensities, subject to a regularizer that ensures smoothness of the displacement field. The effect of the nonlinear structural registration is studied when it is computed on anatomical MR scans and applied to coregistered [15O] water PET scans from the same subjects: in this experiment, a study of visually guided saccadic eye movements. The performance of the nonlinear warp is evaluated using multivariate functional signal and noise measures. These measures prove to be useful for comparing different intersubject registration approaches, e.g., affine versus nonlinear. A comparison of 12-parameter affine registration versus non-linear registration demonstrates that the proposed nonlinear method increases the number of voxels retained in the cross-subject mask. We demonstrate that improved structural registration may result in an improved multivariate functional signal-to-noise ratio (SNR). Furthermore, registration of PET scans using the 12-parameter affine transformations that align the coregistered MR images does not improve registration, compared to 12-parameter affine alignment of the PET images directly.     

Advances in constant envelope coded modulation

An overview is given of recent advances in constant envelope combined coding and modulation. Modulation codes and trellises are discussed, and major classes of trellis modulation codes are described. Continuous phase modulation is defined, and concatenations of phase codes and convolutional codes are examined. The ultimate capability of phase modulation coding and the size of CPM trellis codes are addressed. Implementation issues are considered     

Microstructural modifications and properties of Sn-Ag-Cu solder joints induced by alloying

Slow cooling (1–3°C/sec) of Sn-Ag-Cu and Sn-Ag-Cu-X (X = Fe, Co) solder-joint specimens, made by hand soldering, simulated reflow in a surface-mount assembly to achieve similar as-solidified joint microstructures for realistic shear-strength testing, using Sn-3.5Ag (wt.%) as a baseline. Consistent with predictions from a recent Sn-Ag-Cu ternary phase-diagram study, either Sn dendrites, Ag₃Sn primary phase, or Cu₆Sn₅ primary phase were formed during solidification of joint samples made from the selected near-eutectic Sn-Ag-Cu alloys. Minor substitution of Co for Cu in Sn-3.7Ag-0.9Cu refined the joint-matrix microstructure by an apparent catalysis effect on the Cu₆Sn₅ phase, whereas Fe substitution promoted extreme refinement of the Sn-dendritic phase. Ambient-temperature shear strength was reduced by Sn dendrites in the joint microstructure, especially coarse dendrites in solute poor Sn-Ag-Cu, e.g., Sn-3.0Ag-0.5Cu, while Sn-3.7Ag-0.9Cu with Co and Fe additions have increased shear strength. At elevated (150°C) temperature, no significant difference exists between the maximum shear-strength values of all of the alloys studied.     

Globally optimal transmitter placement for indoor wireless communication systems

A global optimization technique is applied to solve the optimal transmitter placement problem for indoor wireless systems. An efficient pattern search algorithm - DIviding RECTangles (DIRECT) of Jones et al.- has been connected to a parallel three-dimensional radio propagation ray tracing modeler running on a 200-node Beowulf cluster of Linux workstations. Surrogate functions for a parallel wideband code-division multiple-access (WCDMA) simulator were used to estimate the system performance for the global optimization algorithm. Power coverage and bit-error rate are considered as two different criteria for optimizing locations of a specified number of transmitters across the feasible region of the design space. This paper briefly describes the underlying radio propagation and WCDMA simulations and focuses on the design issues of the optimization loop.     

An isotopic method for determining chemically reactive lysine based on succinylation

A method is described for the routine succinylation of proteins using [¹⁴C]succinic anhydride as a means of measuring free ?-amino groups. Maximal succinylation was achieved using 6M guanidine hydrochloride as protein solvent and an 80-fold molar excess of succinic anhydride relative to total lysine residues. Treatment with hydroxylamine (pH 13, 25°C, 5 min) removed unwanted O-succinyl esters. Succinylated protein was precipitated with trichloroacetic acid, residual label washed out with ethanol and the extent of labelling measured in a scintillation counter. The method gave close to theoretical values (n.s., P >0.05) for lysyl residues in egg white lysozyme, bovine haemoglobin, ovalbumin and bovine serum albumin but gave a low value with β-lactoglobulin and an overestimate with insulin attributable to the relatively high contribution of α- relative to ?-amino groups in this low molecular weight protein. The method gave good results for 12 soya protein samples and was shown to be very sensitive to ‘isopeptide-type’ heat damage in these samples. The results correlated well (r = 0.91) with those obtained by the well established dye-bound lysine difference procedure whereas, as could be expected, both these methods correlated poorly with total lysine determinations (r=0.69 for succinic anhydride and r=0.77 for the dye-binding method). The proposed method shows promise as a rapid procedure for the estimation of available lysine, but further studies are necessary to test its ability to measure nutritionally available lysine in all categories of heat damage.     

Network support for IP traceback

This paper describes a technique for tracing anonymous packet flooding attacks in the Internet back toward their source. This work is motivated by the increased frequency and sophistication of denial-of-service attacks and by the difficulty in tracing packets with incorrect, or “spoofed,” source addresses. We describe a general purpose traceback mechanism based on probabilistic packet marking in the network. Our approach allows a victim to identify the network path(s) traversed by attack traffic without requiring interactive operational support from Internet service providers (ISPs). Moreover, this traceback can be performed “post mortem”-after an attack has completed. We present an implementation of this technology that is incrementally deployable, (mostly) backward compatible, and can be efficiently implemented using conventional technology     

Suppression of void coalescence in thermal aging of tin-silver-copper-X solder joints

Addressing the potential for drop impact failure of Pb-free interconnects, the shear ductility after extensive aging of Sn-Ag-Cu (SAC) solders has been improved radically by Co or Fe modifications. Several other SAC+X candidates (X=Mn, Ni, Ge, Ti, Si, Cr, and Zn) now have been tested. Solder joint microstructures and shear strength results show that new SAC+X alloys also suppress void formation and coalescence at the Cu (substrate)/Cu₃Sn interface (and embrittlement) after aging at 150°C for up to 1,000 h. Microprobe measurements of 1,000 h aged samples suggest that Cu substitution by X is usually accentuated in the intermetallic layers, consistent with X=Co and Fe results.