Analysis of temperature-dependent optical gain in GaN-InGaN quantum-well structures

The temperature dependent spectral gain in InGaN-GaN multiple quantum-well structures with 10% In content is investigated. Mode gain is measured in a temperature range between 239 K and 312 K using the Hakki-Paoli technique and compared to simulations. The simulation accounts for temperature-dependent polarization dephasing, and hence homogeneous broadening, in a rigorous fashion, without any fit parameter. It is found that the evolution of the gain spectrum with temperature at different drive currents can be modeled using a temperature-independent single value for inhomogeneous broadening. The resulting compositional fluctuations are compared to structural measurements.     

A Study on the Buckling Behaviour of Strips and Plates with Residual Stresses

During and after rolling or flattening of metal strips and plates the permissible deviations from flatness are described by the permissible absolute wave height and the flatness index. Both values can be determined on a measuring table while the material is not subjected to global tension. Because this procedure is expensive, time‐consuming and allows measurement only at discrete positions along the strip length, on‐line flatness measuring systems are used which can detect the distribution of longitudinal tensile stresses distributed across the strip width allowing for the calculation of the flatness index. This value does not always agree with the value obtained directly by measuring on the table even when the measurement of the longitudinal tensile stress distribution operates perfectly. It can be shown that the measurement of the tensile stress distribution does not give a direct indication on the wave height in the tension‐free state determined on the measuring table. To explain the relationship between tensile stress distribution in the strip and the flatness measurement on the measuring table, the buckling behavior is analysed both with and without dead load for simple symmetrical residual stress distributions resulting, e.g., from the rolling process. Based on the knowledge of the distribution of the longitudinal residual stresses across the strip width, the flatness index and the wave height can be determined by using a specialized finite element model. If the direct measurement is performed under action of dead load, large differences between the directly and indirectly obtained flatness index are observed. Below a certain limit of the intensity of the residual stress distribution the strips and plates lie flat on the measuring table. Above this limit the strip lying on the table exhibits post‐bucking deformations. In the latter case, the wave height increases with strip thickness and intensity of residual stresses.     

Crack Tip Shielding or Anti-shielding due to Smooth and Discontinuous Material Inhomogeneities

This paper describes a theoretical model and related computational methods for examining the influence of inhomogeneous material properties on the crack driving force in elastic and elastic-plastic materials. Following the configurational forces approach, the crack tip shielding or anti-shielding due to smooth (e.g. graded layer) and discontinuous (e.g. bimaterial interface) distributions in material properties are derived. Computational post-processing methods are described to evaluate these inhomogeneity effects. The utility of the theoretical model and computational methods is demonstrated by examining a bimaterial interface perpendicular to a crack in elastic and elastic-plastic compact tension specimens.     

Conservative availability analyses including dependent failures in redundant I&C-systems with recurrent tests

In this paper analytic formulae are derived to estimate conservatively the unavailability of a two out of four digital safety Instrumentation and Control (I&C) system with recurrent tests. The analytic formulae disclose the influence of the different parameters on the system’s unavailability. In particular, the choice of a proper test interval is essential to guarantee the required low unavailability. The extraordinary self-checking capabilities of digital systems are taken into account by use of an appropriate failure model together with the treatment of dependent failures of the integrated software–hardware system. The underlying methodology is approved by licensing experts of nuclear facilities in Germany.     

Photoresist application for the LIGA process

 Fabrication of high aspect ratio structures requires the use of a photoresist able to form a mold with vertical sidewalls. Thus the photoresist should have a high selectivity between the exposed and the unexposed area in the developer. It should be relatively free from stress when applied in thick layers necessary to make high aspect ratio structures. PMMA (Poly Methyl Methacrylate) is the photoresist of choice in the LIGA process, mainly for its ability to hold vertical sidewalls for tall structures. It is applied to the substrate by a glue-down process in which a pre-cast, high molecular weight, sheet of PMMA is attached to the plating base on a substrate. The applied photoresist is then milled down to the precise height by a fly-cutter prior to pattern transfer by x-ray exposure. The requirement that the applied layer be relatively free from stress dictates the choice of glue-down over casting. The substrate preparation steps, as well as the conditioning of the PMMA sheet prior to the glue-down, are done, in part, to reduce the stress in the glued down sheet of photoresist. The cutting of the PMMA sheet in the fly-cutter requires specific operating conditions as well as particular cutting tools to avoid introducing any stress and the resultant crazing of the photoresist. Received: 25 August 1997/Accepted: 3 September 1997     

Anti-scattering X-ray grid

 Various optical or x-ray applications require reduction of scattered radiation on the imaging detector to produce sharper images. The scattered radiation is reduced when the radiation impacting on the detector is from a chosen small solid angle. This requires a mask in front of the detector with small holes and high aspect ratio. We are applying the SLIGA process to perform a proof-of-principle demonstration with the capability of making a large and high area anti-scattering grid. The approach is by assembling and stacking small pieces of grid. To maintain high throughput of the desired radiation, the wall of the grid has to be thin. We designed and fabricated four grid patterns all with 20 μm thick walls and 80 μm×80 μm holes. The individual pieces were 210 μm high and made of nickel. The pieces were assembled and stacked to make a 5 mm×5 mm grid 2.1 mm high. Much larger grids can be made by the SLIGA process, which was chosen because of its capability to fabricate high aspect ratio devices with precision. Received: 25 August 1997/Accepted: 24 October 1997     

Outcome measures of a chronic pain program: a prospective statistical study

Ion beam enhanced deposition (IBED) was adopted to synthesize biocompatible titanium oxide film. Structure characteristics of titanium oxide film were investigated by RBS, AES, and XRD. The blood compatibility of the titanium oxide film was studied by measurements of blood clotting time and platelet adhesion. The results show that the anticoagulation property of titanium oxide film is improved significantly. The mechanism of anticoagulation of the titanium oxide film was discussed.     

Upregulation of osteopontin expression in renal cortex of streptozotocin-induced diabetic rats is mediated by bradykinin

The model of streptozotocin (STZ)-induced diabetes in Wistar rats was used to study the expression of osteopontin during development of diabetic nephropathy. Diabetes was confirmed by serum glucose levels exceeding 16 mmol/l during the experimental period of 12 weeks. During this period of time, diabetic nephropathy developed, as characterized by a reduced glomerular filtration rate (2.7 +/- 0.3 ml/min in controls vs. 1.7 +/- 0.1 ml/min in diabetic rats) and proteinuria (8.3 +/- 1.7 mg/24 h in controls vs. 22.0 +/- 4 mg/24 h in diabetic rats). Northern blot analysis revealed a time-dependent upregulation of renal cortical osteopontin expression reaching 138 +/- 6% of control levels after 2 weeks and 290 +/- 30% (mean +/- SE, n = 6-9) after 12 weeks. By immunostaining, the increased osteopontin expression could be located to the tubular epithelium of the renal cortex. Chronic treatment of animals with ramipril (3 mg/kg) during the 12-week experimental period led to a further increase in osteopontin mRNA expression in diabetic animals, amounting to 570 +/- 73% (mean +/- SE, n = 6) of controls. Increased levels of osteopontin were not associated with accumulation of monocyte/macrophages that were identified by the cell type specific monoclonal antibody ED-1. The increased osteopontin expression in ramipril-pretreated rats was abolished by application of the bradykinin B2-receptor antagonist, icatibant (0.5 mg/kg). In addition, increased osteopontin expression in diabetic rats, which did not receive any treatment after STZ injection, could as well be reduced by icatibant given for the final 2 weeks of the experimental period. These data suggest that a strong bradykinin B2-receptor-mediated upregulation of osteopontin occurs during the pathogenesis of experimental diabetic nephropathy in rats.     

Path-based clustering for grouping of smooth curves and texture segmentation

Perceptual grouping organizes image parts in clusters based on psychophysically plausible similarity measures. We propose a novel grouping method in this paper, which stresses connectedness of image elements via mediating elements rather than favoring high mutual similarity. This grouping principle yields superior clustering results when objects are distributed on low-dimensional extended manifolds in a feature space, and not as local point clouds. In addition to extracting connected structures, objects are singled out as outliers when they are too far away from any cluster structure. The objective function for this perceptual organization principle is optimized by a fast agglomerative algorithm. We report on perceptual organization experiments where small edge elements are grouped to smooth curves. The generality of the method is emphasized by results from grouping textured images with texture gradients in an unsupervised fashion.