Radiation-Induced graft copolymerization of methacrylic acid onto polypropylene fibers. V. Mechanical properties

Mechanical properties of polypropylene-g-poly(methacrylic acid) fibers, prepared by graft copolymerization of methacrylic acid onto polypropylene fiber using simultaneous gamma ray irradiation technique, were evaluated. In general, an improvement in the mechanical behavior of the polypropylene fiber by grafting was observed. Denier and initial modulus of the fiber showed a linear increase with the percent graft, and elongation showed an opposite trend. The results have been explained in terms of reinforcing effect of poly(methacrylic acid) grafts and reduction in the segmental mobility of the polymeric chains. Tenacity also increases up to certain graft level, beyond which a sharp decrease occurs, probably due to the influence on the compactness of the macromolecular chains with the further grafting.     

Microstructural Investigation on Failure of Internal Drive Shaft

17-4 PH stainless steel is used as internal drive shaft material in liquid engine pumps. One of the drive shafts failed during operation. The shaft pieces were in contact for short duration after failure, which has resulted in abrasion of fractured surfaces. Samples from the location of failure were taken, and investigation of the failure was carried out using optical and scanning electron microscopy. The microstructural analysis of the material and fractographic analysis of the fractured surface show that the failure was caused by excessive torsion.     

High-rate vector quantization for detection

We investigate high-rate quantization for various detection and reconstruction loss criteria. A new distortion measure is introduced which accounts for global loss in best attainable binary hypothesis testing performance. The distortion criterion is related to the area under the receiver-operating-characteristic (ROC) curve. Specifically, motivated by Sanov's theorem, we define a performance curve as the trajectory of the pair of optimal asymptotic Type I and Type II error rates of the most powerful Neyman-Pearson test of the hypotheses. The distortion measure is then defined as the difference between the area-under-the-curve (AUC) of the optimal pre-encoded hypothesis test and the AUC of the optimal post-encoded hypothesis test. As compared to many previously introduced distortion measures for decision making, this distortion measure has the advantage of being independent of any detection thresholds or priors on the hypotheses, which are generally difficult to specify in the code design process. A high-resolution Zador-Gersho type of analysis is applied to characterize the point density and the inertial profile associated with the optimal high-rate vector quantizer. The analysis applies to a restricted class of high-rate quantizers that have bounded cells with vanishing volumes. The optimal point density is used to specify a Lloyd-type algorithm which allocates its finest resolution to regions where the gradient of the pre-encoded likelihood ratio has greatest magnitude.     

Preparation of ion‐exchange membranes by hydrolysis of radiation‐grafted polyethylene‐g‐polyacrylamide membranes

Polyethylene‐g‐polyacrylamide membranes were prepared by graft polymerization of acrylamide onto polyethylene films using a preirradiation method. The ion‐exchange membranes were obtained by the hydrolysis of grafted films so as to transform amide groups into carboxyl groups. The fraction of amide groups transformed into carboxyl groups was limited to ～0.5. The characterization and thermal behavior of membranes with different degrees of grafting were evaluated by FTIR, thermogravimetric analysis (TGA), and differential scanning calorimetry (DSC) measurements. The heat of fusion and the crystallinity of polyethylene decreased considerably in the hydrolyzed membranes depending on the degree of grafting. It was found that the grafting of acrylamide led to the reduction in crystallinity due to disruption of the crystallites (crystal defects) and dilution of the inherent crystallinity (dilution effect). The contribution of the hydrolysis step to the crystallinity decrease was negligible. The thermal stability of the membranes as obtained from TGA showed considerable enhancement after hydrolysis. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 149–154, 2003     

Power gain in feedback amplifiers, a classic revisited

A tutorial review of a classic paper by Samuel J. Mason (1954) is described. That paper contained the first definition of a unilateral power gain for a linear two-port and the first proof that this grain is invariant with respect to linear lossless reciprocal four-port embeddings, thereby making it useful as a figure of merit intrinsic to the device. In this work, that original paper is brought up to date, a tutorial exposition of its contents is presented in a modern form, and its significance and applications in microwave engineering are discussed. The subsequent advances in the subject area are summarized, so that the original paper can be placed within a broader context and understood with a more general perspective     

Methods used in dentin bonding tests: an analysis of 50 investigations on bond strength

Researchers have carried out a variety of investigations to determine the properties of available dentin bonding systems. The test methods and variables used in 50 published investigations of bond strength were analyzed. Among the studies analyzed, shear tests predominated, being used in 80% of the studies; dentin from human molar teeth was used most often (in 88% of investigations); and the most prevalent time of testing was 24 hours postcuring. However, a number of potential variables were not recorded in a high proportion of articles, among these the film thickness, the type of dentin tested, and the surface condition (moist or dry). The mode of failure was recorded in only 42% of the investigations assessed. It was found that there is little standardization of test methods in studies of dentin bond strength and that a number of variables are often either not recorded or reported.     

Micromanipulation and cloning studies on buffalo oocytes and embryos using nucleus transfer

1. Nine male volunteers were exposed to the pyrethroid insecticide cyfluthrin. The study was performed in an exposure room, where an aerosol containing cyfluthrin was sprayed to obtain atmospheres with mean cyfluthrin concentrations of 160 and 40 micrograms/m3. Four volunteers were exposed for 10, 30 and 60 min at 160 micrograms/m3 and another five volunteers were exposed for 60 min at 40 micrograms/m3. For 160 micrograms/m3 exposure urine samples were collected before and immediately after exposure as well as for the periods 1-2, 2-3, 3-4, 4-5, 5-6, 6-12 and 12-24 h after exposure. For 40 micrograms/m3 exposure urine samples were collected before and 2 h after exposure. 2. The main urinary cyfluthrin metabolites, cis-/trans-3-(2,2-dichlorovinyl)-2,2-dimethylycyclopropane carboxylic acid (DCCA) and 4-fluoro-3-phenoxybenzoic acid (FPBA), were determined. The limit of detection (LOD) for all metabolites was 0.0025 microgram in an urine sample of 5 ml (0.5 microgram/l). After inhalative exposure of 40 micrograms cyfluthrin/m3 air for 60 min, the amount of metabolites in urine collected in the first 2 h after exposure was less than the LOD, namely 0.14 microgram for cis-DCCA, 0.15-0.28 microgram for trans-DCCA and 0.12-0.23 microgram for FPBA. 3. Of the metabolites, 93% was excreted within the first 24 h (peak excretion rates between 0.5 and 3 h) after inhalative exposure of 160 micrograms/m3. The mean half-lives were 6.9 h for cis-DCCA, 6.2 h for trans-DCCA and 5.3 h for FPBA. 4. The mean trans-:cis-DCCA ratio was 1.9 for the time course as well as for each subject. 5. The amount of metabolites in urine depends on the applied dose, on the exposure time and shows interindividual differences.     

Human papillomavirus investigation of patients with cervical intraepithelial neoplasia 3, some of whom progressed to invasive cancer

Unstable expansion of the CTG repeats in the 3' untranslated region encoding a member of the protein kinase family in the q13.3 band on chromosome 19 is a mutation specific for myotonic dystrophy. To examine the correlation between clinical expression and CTG trinucleotide repeat length, we carried out Southern blot analysis in a family with myotonic dystrophy. In this pedigree, the expanded CTG repeats were transmitted maternally. The mother had three female children. The mother had about 200 CTG repeats, and the number of repeats for each child was about 800, 1500 and 1600 in birth order. The mother and the patient with 800 repeats were unaware of muscle weakness or myotonia. Symptoms were present from age 3 years in the patient with 1500 repeats and from birth in the one with 1600 repeats. Although the mother menstruated regularly, the patients with 800 and 1500 repeats both menstruated irregularly, and the one with 1600 repeats has never menstruated. The age of onset and severity of the disease were correlated with the size of the expanded repeats. Endocrinological studies revealed that the basal levels of the gonadotropins, PRL and E2 were within normal range, and a pituitary response to LHRH was observed. These data suggest that the amenorrhea and menstrual irregularities were caused by a suprahypophyseal dysfunction. When expanded CTG repeats are transmitted maternally, abnormal products resulting from the metabolic disturbance in the affected mother may harm the fetus in utero. A heterozygous fetus, who has more CTG repeats, may be unable to metabolize the pathologic products sufficiently and therefore may become more severely affected. This may explain the exclusive maternal transmission of congenital myotonic dystrophy.