Surface acoustic wave characteristics of ZnO films grown on a polycrystalline 3C-SiC buffer layer

Zinc oxide (ZnO) thin films were deposited onto a polycrystalline (poly) 3C-SiC buffer layer for surface acoustic wave (SAW) applications using a magnetron sputtering system. Atomic force microscopy (AFM) and X-ray diffraction (XRD) showed that the ZnO grown on 3C-SiC/Si had a smooth surface, a dominant c-axis orientation and a lower residual stress in ZnO thin film compared to that grown directly onto Si substrate. In order to evaluate the SAW characteristics of ZnO films on a 3C-SiC buffer layer, the two-port SAW resonators, based on inter-digital transducer (IDT)/ZnO/3C-SiC/Si and IDT/ZnO/Si structures, were fabricated and measured within a temperature range of 25-135 °C. The resulting 3C-SiC buffer layer improved the insertion loss by approximately 7.3 dB within the SAW resonator and enhanced the temperature stability with TCF = −22 ppm/°C up to 135 °C in comparison to that of TCF = −45 ppm/°C within a temperature range of 25-115 °C of the ZnO/Si structure.     

Integrated circuit design for physical unclonable function using differential amplifiers

A physical unclonable function (PUF) based on process variations on silicon wafers is a very promising technology which finds various applications in identification and authentication, but only a few integrated circuits have been reported so far. As those circuits are vulnerable to power supply noises, switching noises and environmental variations, they lead to a reliability issue such as time-varying or metastable responses. To resolve this issue, this letter proposes a new integrated circuit design for PUFs using differential amplifiers. The feasibility of the proposed circuit has been theoretically analyzed and validated through HSPICE simulations for the previous and proposed circuits.     

Effective suppression of signal-wavelength dependent transients in a pump-controlled L-band EDFA

Typical pump-controlled L-band erbium-doped fiber amplifiers (EDFAs) in a feed-forward scheme give significant transients due to gain difference on wavelength of input signal when only a few channels are left. The fiber Bragg grating added pump-controlled L-band EDFA eliminates the wavelength dependent gain difference and transients.     

Subjective Listening Experiments on a Front and Rear Array‐Based WFS System

Wave field synthesis (WFS) has been gathering more and more attention recently due to its ability to perfectly reproduce an original sound field. However, to realize theoretically perfect WFS, a four‐sided loudspeaker array that encloses the listener is required. However, it is difficult to build such a system except in large listening spaces, such as a theater or concert hall. In other words, if the listening space is a home, installing a side loudspeaker array is impractical. If the two side walls located to the left and right of the listener can be omitted, a setup using only front and rear loudspeaker arrays may be a solution. In this letter, we present a subjective listening experiment of sound localization/distance based on a WFS using a front and rear loudspeaker array system which is conducted on two listening points and shows average localization errors of 6.1° and 9.18°, while the average distance errors are –27% (0.5 m) and –29% (0.6 m), respectively.     

Secure group communications using key graphs

Many emerging network applications are based upon a group communications model. As a result, securing group communications, i.e., providing confidentiality, authenticity, and integrity of messages delivered between group members, will become a critical networking issue. We present, in this paper, a novel solution to the scalability problem of group/multicast key management. We formalize the notion of a secure group as a triple (U,K,R) where U denotes a set of users, K a set of keys held by the users, and R a user-key relation. We then introduce key graphs to specify secure groups. For a special class of key graphs, we present three strategies for securely distributing rekey messages after a join/leave and specify protocols for joining and leaving a secure group. The rekeying strategies and join/leave protocols are implemented in a prototype key server we have built. We present measurement results from experiments and discuss performance comparisons. We show that our group key management service, using any of the three rekeying strategies, is scalable to large groups with frequent joins and leaves. In particular, the average measured processing time per join/leave increases linearly with the logarithm of group size     

A fully integrated switched-capacitor DC–DC converter with hybrid output regulation

In this paper, we propose a fully integrated switched-capacitor (SC) DC–DC converter with hybrid output regulation that allows a predictable switching noise spectrum. The proposed hybrid output regulation method is based on the digital capacitance modulation for fine regulation and the automatic frequency scaling for coarse regulation. The automatic frequency scaler and on-chip current sensor are implemented to adjust the switching frequency at one of the frequencies generated by a binary frequency divider with change in load current. Thus, the switching noise spectrum of the proposed SC DC–DC converter can be predicted over the entire load range. In addition, the bottom-plate losses due to the parasitic capacitances of the flying capacitors and the gate-drive losses due to the gate capacitances of switches are reduced at light load condition since the switching frequency is automatically adjusted. The proposed SC DC–DC converter was implemented in a 0.13 µm CMOS process with 1.5 V devices, and its measurement results show that the peak efficiency and the efficiency at light load condition are 69.2% and higher than 45%, respectively, while maintaining a predictable switching noise spectrum.     

A new predictive search area approach for fast block motion estimation

According to the observation on the distribution of motion differentials among the motion vector of any block and those of its four neighboring blocks from six real video sequences, this paper presents a new predictive search area approach for fast block motion estimation. Employing our proposed simple predictive search area approach into the full search (FS) algorithm, our improved FS algorithm leads to 93.83% average execution-time improvement ratio, but only has a small estimation accuracy degradation. We also investigate the advantages of computation and estimation accuracy of our improved FS algorithm when compared to the edge-based search algorithm of Chan and Siu (see IEEE Trans. Image Processing, vol.10, p.1223-1238, Aug. 2001); experimental results reveal that our improved FS algorithm has 74.33% average execution-time improvement ratio and has a higher estimation accuracy. Finally, we further compare the performance among our improved FS algorithm, the three-step search algorithm, and the block-based gradient descent search algorithm.     

A low-noise L-band EDFA with a 1500-nm Raman-pumped dispersion-compensating fiber section

This report presents a low-noise L-band erbium-doped fiber amplifier (EDFA) with a dispersion-compensating Raman amplifier. With an optimized prestage and 1500-nm Raman-pump laser diodes, the proposed EDFA achieved an internal noise figure of less than 4.5 dB over a 33-nm flat gain bandwidth within 0.5 dB at -2 dBm of large signal input power.     

Highly Customizable All Solution–Processed Polymer Light Emitting Diodes with Inkjet Printed Ag and Transfer Printed Conductive Polymer Electrodes

Inkjet and transfer printing processes are combined to easily form patterned poly(3,4‐ethylenedioxythiophene):poly(styrenesulfonate) (PEDOT:PSS) films as top anodes of all solution–processed inverted polymer light emitting diodes (PLEDs) on rigid glass and flexible plastic substrates. An adhesive PEDOT:PSS ink is formulated and fully customizable patterns are obtained using the inkjet printing process. In order to transfer the patterned PEDOT:PSS films, adhesion properties at interfaces during multistep transfer printing processes are carefully adjusted. The transferred PEDOT:PSS film on the plastic substrates shows not only a sheet resistance of 260.6 Ω/□ and a transmittance of 92.1% at 550 nm wavelength but also excellent mechanical flexibility. The PLEDs with spin‐coated functional layers sandwiched between the transferred PEDOT:PSS top anodes and inkjet‐printed Ag bottom cathodes are fabricated. The fabricated PLEDs on the plastic substrates show a high current efficiency of 10.4 cd A^?1 and high mechanical stability. It is noted that because both Ag and PEDOT:PSS electrodes can be patterned with a high degree of freedom via the inkjet printing process, highly customizable PLEDs with various pattern sizes and shapes are demonstrated on the glass and plastic substrates. Finally, with all solution process, a 5 × 7 passive matrix PLED array is demonstrated.