基于S3C2440嵌入式视频传输系统的研究与设计

如今嵌入式和视频行业发展的如火如荼,视频传输也得到了很好的发展,而很多视频传输设备都比较昂贵且移动不灵活.鉴于此,设计出了以S3C2440为核心芯片,并在此基础上结合linux环境下的GStreamer流媒体框架的视频传输系统,系统采用无线的传输方式.经过对系统测试,此系统能流畅的播放传输的视频并且移动灵活,达到预期目标,并且该系统简洁、成本低具备实际的应用前景.     

萃取色层技术分离提纯稀土的现状与展望

萃取技术分离难以分离得到高纯单一重稀土,尚需萃取色层技术.本综述简要介绍了萃取色层分离技术要点,对国内外萃取色层技术分离提纯稀土的现状和发展情况进行了综述和分析,提出了萃取色层技术分离提纯稀土所面对的关键技术问题和展望.迄今用于稀土元素分离的萃淋树脂所含的萃取剂主要为酸性含磷萃取剂,包括P507,P204,5709等,制约其工业化应用的主要原因是淋洗酸浓度过高、且需采用梯度淋洗.Cyanex272萃淋树脂是分离稀土的发展方向.结论指出,应加强萃淋树脂对金属萃取饱和容量的提高、减少萃取剂损失及加强传质数学模型等基础课题的研究,为工业应用提供理论依据.预计萃淋树脂技术将会在稀土元素的分离中得到实际广泛的应用.     

基于仿射传播的有向网络聚类算法

现有大多数的网络聚类方法都只是针对无向网络, 已有的有向网络聚类方法建立在传统聚类算法基础之上, 存在着一定的局限性。针对上述问题, 提出一种基于仿射传播的有向网络聚类算法, 该算法首先采用SimRank作为节点之间的相似度, 并将计算得到的结果转换为适应于仿射传播算法的负值; 然后将相似度矩阵作为输入, 利用具有更好性能的仿射传播算法对有向网络进行聚类。实验结果表明, 所提出算法的聚类性能优于其他几种具有代表性的有向网络聚类算法。     

Novel method for preparation of quaternary ammonium ionomer from epoxidized styrene–butadiene–styrene triblock copolymer and its use as compatibilizer for blending of styrene–butadiene–styrene and chlorosulfonated polyethylene

A novel method for the preparation of a quaternary ammonium ionomer of styrene–butadiene–styrene triblock copolymer (SBS) was developed by a ring‐opening reaction of epoxidized SBS with triethylamine hydrochloride in the presence of a phase transfer catalyst. The optimum conditions were studied. The ionomer was characterized by quantitative analysis, IR spectroscopy, and ¹H‐NMR spectroscopy. Its water absorbency, oil absorbency, dilute solution viscosity, and use as a compatibilizer for the blending of SBS and chlorosulfonated polyethylene (CSPE) were investigated. The results showed that, under optimum conditions, the epoxy groups can be completely converted to the quaternary ammonium groups. The IR spectrum did not exhibit the absorption peak for quaternary ammonium groups, whereas the ¹H‐NMR spectrum and titration method demonstrated it. With increasing ionic group content, the water absorbency of the ionomer increased whereas its oil absorbency decreased. These indicated the amphiphilic character of the SBS ionomer. The dilute solution viscosity of the ionomer in toluene/methanol (9/1) solvent increased with increasing quaternary ammonium group content. The ionomer was used as a compatibilizer for the blends of SBS and CSPE. The addition of a small amount of the ionomer to the blend enhanced the mechanical properties of the blends: 2 wt % ionomer based on the blend increased the tensile strength and ultimate elongation of the blend nearly 2 times. The blends of equal parts SBS and CSPE behaved as oil‐resistant thermoplastic elastomers. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 99: 1975–1980, 2006     

Characteristic modes and flow structure of non-premixed flame in humid-air combustion

An experimental study has been performed in order to determine the effect of humidity on the flow field and the flame stability limit in turbulent non-premixed flame. Two-dimensional Particle Image Velocimetry (PIV) measurements were made to quantify the velocity field, with and without steam injected. The results indicate the addition of steam decreases the recirculation flow and reduces the distance between the forward and aft stagnation points. The detailed stabilization regimes show that the critical fuel-to-air velocity ratios of the central fuel penetration in the humid air case are 16% to 22% lower, and the partially quenching limits are at least 25% lower. The decreased penetration limit is due to a reduction in momentum of the humid air. An analysis of flamelet concepts reveals that increased chemical reaction time leads to lower partially quenching limits in the humid air combustion.     

聚氯乙烯／蒙脱土复合材料的结构与性能研究

采用熔融共混法制备得到PVC／蒙脱土复合材料。通过X射线衍射和透射电镜对复合材料的结构进行了表征。研究了钠基蒙脱土和烷基季铵盐改性的有机蒙脱土对聚氯乙烯／蒙脱土复合材料的结构、加工热稳定性、光学性能、力学性能和结构流变性能的影响。     

Modeling of photocatalytic oxidation of VOCs in a packed bed reactor under continuous and discontinuous illuminations

In this paper, a mathematical model is presented to describe the photocatalytic degradation of VOCs in a packed bed reactor. Here, the adsorption of VOCs on the wall of the reactor is taken into account and the diffusion of VOCs in the axial direction is neglected. First-order kinetics is used to describe the photocatalytic oxidation of VOCs. The analytical solution of the present model is obtained by traveling wave method. The solution shows that the reactor performance is totally dependent on the inlet concentration of VOCs when the time is large enough. The present model is validated through the experimental result of the photocatalytic oxidation of trichloroethylene in a packed bed and the predicted results accord well with the experimental data. The influence of flow rate and inlet concentration on the performance of the reactor is discussed in detail. High flow rate offers high reaction rate and low conversion efficiency. The different inlet conditions and different reaction patterns are also investigated. The model would be useful to estimate the rate constant and help to the design of the reactor.     

Synthesis and characterization of poly(butyl acrylate)/silica and poly(butyl acrylate)/silica/poly(methyl methacrylate) composite particles

Poly(butyl acrylate)/poly(methyl methacrylate) (PBA/PMMA) core–shell particles embedded with nanometer‐sized silica particles were prepared by emulsion polymerization of butyl acrylate (BA) in the presence of silica particles preabsorbed with 2,2′‐azobis(2‐amidinopropane)dihydrochloride (AIBA) initiator and subsequent MMA emulsion polymerization in the presence of PBA/silica composite particles. The morphologies of the resulting PBA/silica and PBA/silica/PMMA composite particles were characterized, which showed that AIBA could be absorbed effectively onto silica particles when the pH of the dispersion medium was greater than the isoelectric potential point of silica. The critical amount of AIBA added to have stable dispersion of silica particles increased as the pH of the dispersion medium increased. PBA/silica composite particles prepared by in situ emulsion polymerization using silica preabsorbed with AIBA showed higher silica absorption efficiency than did the PBA/silica composite particles prepared by direct mixing of PBA latex and silica dispersion or by emulsion polymerization in which AIBA was added after the mixing of BA and silica. The PBA/silica composite particles exhibited a raspberrylike morphology, with silica particles “adhered” to the surfaces of the PBA particles, whereas the PBA/silica/PMMA composite latex particles exhibited a sandwich morphology, with silica particles mainly at the interface between the PBA core and the PMMA shell. Subsequently, the PBA/silica/PMMA composite latex obtained had a narrow particle size distribution and good dispersion stability. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 99: 3425–3432, 2006     

Nanocrystalline CeO2 in SBA-15: Performance of Pt/CeO2/SBA-15 Catalyst for Water-gas-shift Reaction

CeO₂ particles confined within the pores of an SBA-15 mesoporous silica host were prepared by incipient wetness impregnation (IMP) and deposition precipitation (DP) methods. The materials were characterized by XRD, N₂-adsorption and temperature programmed reduction (TPR) to evaluate the structure, texture, and redox properties. The preparation procedure had significant impact on the assembling mode of CeO₂ inside the SBA-15 mesopores. A high dispersion of CeO₂ particles was achieved via DP, whereas the dispersion of CeO₂ prepared by IMP was found to be inhomogeneous and CeO₂ partially blocked the pores. The CO conversion in the water-gas-shift reaction was enhanced over 1 wt% Pt supported on CeO₂-modified SBA-15 obtained by DP.     

浅谈海南影视动画产业发展中的政府作为

影视动画产业是当今社会的朝阳产业,是传统经济发展和延伸的一种新方式,政府对影视动画产业十分重视.而影视文化产业具有浓厚文化色彩和广阔的自由发展空间,有利于影视动画的进一步发展与建设.影视动画产业发展对象可以是影视基地,也可以是影视剧本,产业发展对象丰富,所以此产业的发展前景非常明朗,并且还具有高度的研究价值.