Characterization of SrWO4-PVA and SrWO4 spiders’ webs synthesized by electrospinning

Mixtures of strontium acetate, ammonium metatungstate hydrate, and different contents of poly (vinyl alcohol) (PVA, 125,000 MW) were electrospun by a +15 kV direct voltage to synthesize SrWO₄-PVA spiders’ webs. The spider's web, synthesized from the solution containing 1.3 g PVA, was further calcined in air at 300-600 °C for 3 h. The SrWO₄-PVA spider's web was analyzed by thermogravimetric analyzer (TGA) to specify the evaporation and decomposition of PVA and volatile components. In addition, the SrWO₄-PVA and SrWO₄ spiders’ webs were characterized by X-ray diffractometer (XRD), selected area electron diffraction (SAED), scanning and transmission electron microscopes (SEM, TEM), and ultraviolet (UV)-visible and photoluminescence (PL) spectrometers, including the vibration modes by Fourier transform infrared (FTIR) and Raman spectrometers. A possible formation mechanism of SrWO₄-PVA and SrWO₄ spiders’ webs was also proposed according to the experimental results.     

Solvothermal synthesis of CdS nanowires templated by polyethylene glycol

CdS nanowires were solvothermally synthesized from Cd(NO₃)₂ and S powder using ethylenediamine as a solvent and polyethylene glycol (PEG) as a template. Hexagonal CdS with P6₃mc space group was detected using XRD and SAED, results which are in good accordance with those obtained by the simulation. SEM, TEM and HRTEM revealed the gradual development of nanowires in the [0 0 1] direction with a number of atoms aligning in a crystal lattice. Raman spectra of different products showed the fundamental and overtone modes at the same wavenumbers of 300 and 601 cm⁻¹, respectively. Their relative intensities at different molecular weight PEG were influenced by the anisotropic geometry of the products. Their photoluminescence peaks were detected at the same wavelengths of 518 nm. A formation mechanism for CdS nanowires was also proposed to relate to the experimental results.     

Fuel consumption and emission comparison of conventional and hydrogen feed vehicles

Current environmental concerns on nitrogen oxides (NO_x) and particulate matter (PM) emissions caused by diesel engines have led researchers to be interested in investigating vehicles with alternative power sources. Because of this reason, vehicle models with SI engine were adopted in the conducted study. Firstly, as an initial step, 1-D SI engine models were created with use of AVL Boost software. A four-cylinder engine model was created for conventional vehicle model, while a two-cylinder downsized engine was adopted as a subsystem of hybrid vehicle model. The models were based on experimental data obtained from a laboratory test setup with a single-cylinder engine. Subsequently, detailed engine maps on emissions and fuel consumption were generated with the developed ANN model. The fuel consumption and emission data, which were gathered from NEDC and WLTC simulations, were compared for conventional ICE, PEM FC and PEM FC + ICE powered vehicles with the help of the vehicle model which was developed by using Matlab Simulink software. Based on the results, it was concluded that there might be sufficient improvement in fuel consumption and significant improvement in emissions with the use of PEM FC that a hybrid driving system (PEM FC + ICE) can be utilized, and that emissions can be at 0 with the sole use of PEM FC.     

Effect of fin pitches on the optimum heat transfer performance of crimped spiral fin-and-tube heat exchangers

This study conducted experiments on the optimized fin pitch for crimped spiral fin-and-tube heat exchangers. The experiments covered a size range of 2.4–6.5 mm, which is the manufacturing limitation for this kind of fin. The water-flow arrangement used in this experiment combined the parallel cross-flow and the counter cross-flow in a two-row configuration. Ambient air was used as the working fluid on the air-side, and hot water was used on the tube-side. The effects of fin pitches on the heat transfer coefficient and pressure drop characteristics were studied. The results clearly showed that the convective heat transfer coefficient (h_o) for a fin pitch of 2.4 mm is relatively low compared with that of other fin pitches with the same air frontal velocity. Using larger fin pitches (i.e., 4.2, 6.2, and 6.5 mm) resulted in negligible differences in the pressure drop. Moreover, this work introduces the parameter of three performances indexes, which can be expressed as the ratio of the desired output to the required input, for optimization purposes. Due to the difference in optimum fin pitch obtained by these performance indexes, an intersection analysis was conducted. The results indicated that the optimum fin pitch is 4.2 mm for this work, which could be valuable for the effective design for industrial thermal-system applications.     

Unconfined laminar nanofluid flow and heat transfer around a square cylinder

The momentum and forced convection heat transfer for a laminar and steady free stream flow of nanofluids past an isolated square cylinder have been studied numerically. Different nanofluids consisting of Al₂O₃ and CuO with base fluids of water and a 60:40 (by mass) ethylene glycol and water mixture were selected to evaluate their superiority over conventional fluids. Recent correlations for the thermal conductivity and viscosity of nanofluids, which are functions of particle volumetric concentration as well as temperature, have been employed in this paper. The simulations have been conducted for Pe = 25, 50, 100 and 200, with nanoparticle diameters of 30 and 100 nm and particle volumetric concentrations ranging from 0% to 4%. The results of heat transfer characteristics of nanofluid flow over a square cylinder showed marked improvement comparing with the base fluids. This improvement is more evident in flows with higher Peclet numbers and higher particle volume concentration, while the particle diameter imposes an adverse effect on the heat transfer characteristics. In addition, it was shown that for any given particle diameter there is an optimum value of particle concentration that results in the highest heat transfer coefficient.     

Characterization of Bi2S3 with different morphologies synthesized using microwave radiation

Bi₂S₃ with different morphologies (nanoparticles, nanorods and nanotubes) was synthesized using bismuth nitrate pentahydrate (Bi(NO₃)₃·5H₂O) and two kinds of sulfur sources (CH₃CSNH₂ and NH₂CSNH₂) in different solvents (water, ethylene glycol and propylene glycol) via a microwave radiation method at 180 W for 20 min. X-ray powder diffraction (XRD), scanning electron microscopy (SEM) and transmission electron microscopy (TEM) indicated that all of the products are orthorhombic Bi₂S₃ phase of nanoparticles, nanorods and nanotubes, influenced by the sulfur sources and solvents. Formation mechanisms of the products with different morphologies are also proposed.     

Sulfur- and water-tolerance of Pt/KL aromatization catalysts promoted with Ce and Yb

Different Pt/KL catalysts containing rare earth (RE; Ce and Yb) promoters were prepared by two techniques, incipient wetness impregnation (IWI) and vapor phase impregnation (VPI). The catalysts were tested for the activity and the selectivity of n-hexane aromatization to benzene under clean, sulfur-containing, and water-containing feeds at 500 °C. It was observed that the catalysts prepared by the VPI technique exhibited much higher activity and selectivity than those prepared by IWI. It was also found that although under clean conditions, the addition of Ce or Yb caused a decrease in activity, in the presence of sulfur the addition of Ce and to a lesser extent Yb, significantly inhibited catalyst deactivation.

The influence of water in the feed was investigated by contacting the catalysts for 1 h to a feed containing 3 mol.% water. After this treatment, all the catalysts exhibited a significant activity loss. This loss was more pronounced for the catalyst prepared by the VPI method. The catalyst prepared by IWI already had suffered a significant deactivation before the water treatment, so the activity drop was not so pronounced. The sample prepared by VPI not only showed a drop in activity immediately after the water treatment but it became more susceptible to deactivation afterwards. By contrast, the Ce-promoted catalyst showed a more stable activity after the water treatment.

All catalysts were characterized before and after reaction by a number of techniques. In agreement with previous studies, FT-IR of adsorbed CO and chemisorption results indicated that the VPI method resulted in higher Pt dispersion than that obtained by the IWI method. After reaction in the presence of sulfur, the Ce-promoted Pt/KL catalyst showed a higher resistance to metal agglomeration and a lower rate of coke formation than the unpromoted Pt/KL. On all the catalysts, the amount of carbon deposits was greater in the presence of sulfur and after exposure to water vapor than under the reaction with clean feeds. This difference is explained in terms of metal particle growth and location in the zeolite.     

Malic acid complex method for preparation of LiNiVO4 nano-crystallites

LiNiVO₄ nano-crystallites were prepared by the polymerized complex method using Li₂CO₃, Ni(CH₃COO)₂·4H₂O and NH₄VO₃ as starting reagents and malic acid as a complexing agent. With the subsequent calcination at 450 °C, the powder analyzed by XRD, FTIR, Raman, electron diffraction, SEM and TEM techniques was found to be inverse spinel LiNiVO₄ with ∼20 nm in diameter. TGA shows continuous weight loss at 40–450 °C due to the evaporation and decomposition processes. Above 450 °C, weight percent tended to be constant. In addition, formation mechanism of the purified LiNiVO₄ was proposed to relate with the experimental results.     

Effects of ethylenediamine to water ratios on cadmium sulfide nanorods and nanoparticles produced by a solvothermal method

Cadmium sulfide nanorods and nanoparticles were successfully produced by a solvothermal reaction at 200 °C for 24 h using ethylenediamine and water as pure and mixed solvents. The products were analyzed by X-ray diffraction, Raman spectroscopy and transmission electron microscopy. In pure ethylenediamine, they show the hexagonal structure CdS nanorods with 0.2-2 μm long and 30 nm diameter, and the 1LO and 2LO modes at 299.36 and 600.72 cm^− 1, respectively. Growth of CdS nanorods is along the [001] direction, interpreted by HRTEM images and SAED patterns. In the 50:50 vol.% of ethylenediamine:water mixed solvents, the length of CdS nanorods decreased to 100-200 nm. The CdS nanoparticles were produced when pure water was used.     

Characterization of AgBiS2 nanostructured flowers produced by solvothermal reaction

AgBiS₂ nanostructured flowers were produced from CH₃COOAg, Bi(NO₃)₃.5H₂O and thiosemicarbazide (NH₂CSNHNH₂) using different solvents [ethylene glycol (EG), water (H₂O), polyethylene glycol with molecular weight of 200 (PEG200), and propylene glycol (PG)] in Teflon-lined stainless steel autoclaves. The phase and purity were detected using X-ray diffraction (XRD), controlled by the solvents. The product was purified AgBiS₂ produced by the 200 °C and 24 h reaction in EG, corresponding to selected area electron diffraction (SAED) and simulation patterns. Scanning and transmission electron microscopies (SEM and TEM) revealed the formation of nanostructured flowers — enlarged by the increase in the lengths of time and temperature. Their photoluminescence (PL) emissions were detected at the same wavelength of 382 nm (3.24 eV), although they were produced under different conditions.