A study on the degree of deliberation and meditation of cyber poll respondents for nuclear-related decision making

Public participation is essential in each step of the nuclear-related decision-making process. Recently, the electronic systems using the Internet have become quite popular, and have emerged as a good medium for communicating with the public. In this study, a comprehensive utilization of electronic public participation was used to analyze public opinion on a given nuclear-related decision-making process. The degree of deliberation and meditation of the public participating in an electronic poll survey was evaluated, and the decision-making factors representing the personal characteristics of the poll respondents such as age, income, education, residence, degree of knowledge and concern were carefully incorporated when preparing the poll-survey questionnaire for its evaluation. Fuzzy analysis was used to assess and aggregate the responses to each decision-making factor. As a case study, this procedure was used to analyzing public opinion on the location of a low-level radioactive waste disposal facility on the campus of Seoul National University. The results show that there is a tendency of respondents who are on the negative side of the argument to be more deliberate and meditative in their decision-making process than those on the positive side. Knowledge and residence were found to be important decision-making factors.     

Application of Code Approach for Emergency Evacuation in a Rail Station

This paper presents an emergency evacuation analysis during a mid-platform train fire in an underground rail station. A time-based evacuation scenario is developed taking into account the stairway inaccessibility due to smoke blockage. The calculation approach in NFPA 130 is then applied to a parametric study of this time-based scenario and its reliability is examined using a micro-simulation model. Both methods give consistent predictions of the exiting times. The results demonstrate that with the division of the station into two zones, the exiting time could not meet the code requirements, whereas it does meet the required exiting time without the division. Such division is due to smoke blockage and creates an uneven ratio of the occupant load to the available exiting capacity. This shows that appropriate consideration of the fire and smoke effects is important for station egress evaluation. Other issues such as the fire growth rate and the pre-evacuation time are also discussed.     

薄板坯连铸连轧工艺对铌微合金化高强度钢组织和性能的影响

首先建立薄板坯连铸连轧工艺的试验室模拟技术，并运用该模拟技术，研究薄板坯连铸连轧工艺(CSP)和传统板坯再加热工艺(TRP)两种工艺对铌微合金化高强度钢的显微组织和力学性能的影响。研究结果表明：CSP钢的晶粒细化效果不如TRP钢，两者的平均铁素体晶粒尺寸分别为8．17μm和6．30μm。在CSP试验钢板中铌的析出量较大，特别是在铁素体中细小颗粒的铌的析出物较多，沉淀强化效果较强。CSP试验钢的σ0.5和σb分别较TRP工艺低约40MPa和约25MPa，同时其低温冲击韧性较好，FATT温度较低。     

Formation and retention of local melted films in AZ91 friction stir spot welds

The formation of local melted films during friction stir spot welding of as-cast AZ91D and thixomolded AZ91 material is investigated. The average temperatures close to the tip of the rotating pin vary from 438 to 454 °C during the dwell period in friction stir spot welding. These measured temperature values are higher than the melting temperature of α-Mg + Mg₁₇Al₁₂ eutectic (437 °C). It is suggested that the temperature in the stir zone during the dwell period is determined by the relative proportions of α-Mg and (α-Mg + Mg₁₇Al₁₂) eutectic material, which are incorporated during friction stir spot welding. Based on the stir zone temperature measurements and a detailed examination of material located at the root of the pin thread it is suggested that material is moved downwards via the pin thread and into the stir zone during the dwell period in friction stir spot welding. Evidence of local melted film formation is observed in the stir zone of AZ91 spot welds. It is suggested that melted films are retained since their dissolution rate is much slower in the high temperature stir zone than it is when melted films is formed in the stir zone during Al 7075-T6 friction stir spot welding. The spontaneous melting temperature, solute diffusion rate and the thermodynamic driving force for droplet dissolution are much higher during Al 7075-T6 friction stir spot welding.     

合成2,4-二叔丁基苯酚工业试验

以离子交换树脂为催化剂，苯酚和甲基叔丁基醚为原料合成2，4-二叔丁基苯酚(简称2，4酚)，合成产物经过滤再经间歇真空精馏精制提纯，得到高纯度的2，4酚成品。成品精馏后釜中残液在酸性白土催化剂的作用下通过歧化反应生成对叔丁基苯酚，再经精馏提纯得到成品对叔丁基苯酚。通过工艺优化，使2，4酚、对叔丁基苯酚形成联产生产工艺，降低了生产原料消耗和成本。     

ZJ510L-B汽车用高强度热轧板的试制

珠钢150t电弧炉-LF(VD)-CSP(紧凑式带材生产)流程试生产的5～8mm ZJ510L-B(0．16C--1．22Mn)汽车用高强度热轧板的铁素体晶粒尺寸为6．0～9．2μm，带状组织为1．5～2．5级，强度极限σb562～610MPa，延伸率δ5 32．0％～38．6％。文中还分析和提出了带状组织的形成原因和改进措施。     

An alternative method to compute the component fractions in the geometrical optical model: visual computing method

A method called visual computing was used to solve angular four-components' proportions and directional vegetation cover fraction for discrete canopies and continuous row-planted plants. It proved effective to predict the angular characteristics on pixel scale. The method could be an alternative way to a classical solution of geometrical optical models. A visual computing method would be effective especially when the canopies' spatial distribution and shapes were irregular and could not be described statistically.     

基于多代理技术的传感器管理系统

针对分布式对空监视网中混合式传感器管理结构存在的问题，提出了基于多代理技术的混合式传感器管理结构。该结构较好地克服了混合式管理结构中在融合中心存在的瓶颈问题，通过多个传感器代理、融合中心代理之间的相互协商来实现传感器任务的分配。传感器代理与传感器相结合使传感器的工作模式实现高度的自动化和模块化，便于传感器的灵活组网。     

脉冲电镀最佳参数之探索和优化

本文利用正交实验法对脉冲电镀各控制参数进行试验,对影响分散能力、镀层可靠性及外观质量的各种因素进行探讨,寻找影响外观质量的显著因子并加以控制,同时进一步优化脉冲电镀的工艺参数。