Performance characteristics of refrigeration cycle with parallel compression economization

Thermodynamic analyses and economizer pressure optimizations of ammonia, propane and isobutane‐based refrigeration cycles with parallel compression economization are presented in this article. Energetic and exergetic performance comparisons with transcritical CO₂ cycle are presented as well. Results show that the optimum economizer mass fraction as well as COP improvement increase with increase in cycle temperature lift. The expression for optimum economizer pressure has been developed. Study shows that the performance improvements using parallel compression economization are strongly dependent on the refrigerant properties as well as the operating conditions. Using parallel compression economization, carbon dioxide yields maximum COP improvement of 31.9% followed by propane (29.8%), isobutane (27.2%) and ammonia (11.3%) for studies ranges. In spite of higher COP improvement, the cooling COP as well as second low efficiency for carbon dioxide is still significantly lower than that for others. Component‐wise irreversibility distributions show the similar trends for all refrigerants except CO₂. Employing parallel compression economization in refrigeration cycle not only improves the cooling COP but also increase the compactness of evaporator. Copyright © 2010 John Wiley & Sons, Ltd.     

Enhanced bioaccessibility of β‐carotene from yellow‐orange vegetables and green leafy vegetables by domestic heat processing

Effect of heat treatment involved in domestic cooking on the bioaccessibility of β‐carotene from yellow‐orange as well as green leafy vegetables was evaluated. Heat treatment of these vegetables by pressure‐cooking, stir‐frying and open‐pan boiling had a beneficial influence on the bioaccessibility of β‐carotene. The extent of increase in the per cent bioaccessibility of β‐carotene as a result of pressure‐cooking was 21–84%. Stir‐frying in presence of a small quantity of oil brought about an enormous increase in the bioaccessibility of β‐carotene from these vegetables, the extent of increase being 67–191%. Open‐pan boiling of vegetables increased the bioaccessibility of β‐carotene in the range 23–36%. Thus, among the three domestic heat processing methods, stir‐frying results in maximum bioaccessibility of this provitamin. The use of suitably heat‐processed vegetable sources of β‐carotene could form a dietary strategy to derive this micronutrient maximally by the population dependent on plant foods.     

Aqueous-Phase Synthesis of Silver Nanodiscs and Nanorods in Methyl Cellulose Matrix: Photophysical Study and Simulation of UV–Vis Extinction Spectra Using DDA Method

We present a very simple and effective way for the synthesis of tunable coloured silver sols having different morphologies. The procedure is based on the seed-mediated growth approach where methyl cellulose (MC) has been used as soft-template in the growth solution. Nanostructures of varying morphologies as well as colour of the silver sols are controlled by altering the concentration of citrate in the growth solution. Similar to the polymers in the solution, citrate ions also dynamically adsorbed on the growing silver nanoparticles and promote one (1-D) and two-dimensional (2-D) growth of nanoparticles. Silver nanostructures are characterized using UV–vis and HR-TEM spectroscopic study. Simulation of the UV–vis extinction spectra of our synthesized silver nanostructures has been carried out using discrete dipole approximation (DDA) method.     

Biohydrogen production from forest and agricultural residues for upgrading of bitumen from oil sands

In this study, forest residues (limbs, tops, and branches) and straw (from wheat and barley) are considered for producing biohydrogen in Western Canada for upgrading of bitumen from oil sands. Two types of gasifiers, namely, the Battelle Columbus Laboratory (BCL) gasifier and the Gas Technology Institute (GTI) gasifier are considered for biohydrogen production. Production costs of biohydrogen from forest and agricultural residues from a BCL gasification plant with a capacity of 2000 dry tonnes/day are $1.17 and $1.29/kg of H₂, respectively. For large-scale biohydrogen plant, GTI gasification is the optimum technology. The delivered-biohydrogen costs are $2.19 and $2.31/kg of H₂ at a plant capacity of 2000 dry tonnes/day from forest and agricultural residues, respectively. Optimum capacity for biohydrogen plant is 3000 dry tonnes/day for both residues in a BCL gasifier. In a GTI gasifier, although the theoretical optimum sizes are higher than 3000 dry tonnes/day for both feedstocks, the cost of production of biohydrogen is flat above a plant size of 3000 dry tonnes/day. Hence, a plant at the size of 3000 dry tonnes/day could be built to minimize risk. Carbon credits of $119 and $124/tonne of CO₂ equivalent are required for biohydrogen from forest and agricultural residues, respectively.     

Synthesis,mechanical properties and bioactivity of nanostructured zirconia

Yttria stabilized zirconia 3Y – TZP nanopowders (10–30 nm) are prepared through direct precursor calcination of mixed zirconium oxychloride and yttrium nitrate solutions at 600 °C for 2 h. Cuboid(50 × 25 × 20 mm³) zirconia blanks are fabricated through centrifuge casting and followed by sintering at 1350 °C for 2 h. Sintered zirconia blanks exhibit 24% volume shrinkage and 98% relative density with average grain size of 250 nm. Vickers hardness and indented fracture toughness of sintered blanks are measured as 13.5 GPa and 3.5 MPa.m^1/2, respectively. Bioactivity of nanostructured zirconia originates after four weeks incubation in simulated body fluid solution. An optimum time is required for the deposition of hydroxyapatite nanoparticles on stress-induced nucleation site of nanostructured zirconia.     

Use of advance demand information in multi-stage production-inventory systems with multiple demand classes

This paper considers three-stage production-inventory systems serving two customer classes, where only one class provides advance demand information and early order fulfilment is acceptable. We propose a new approach for production replenishment and order fulfilment in such systems that uses advance demand information for performance improvement. The approach combines the benefits of early fulfilment and Kanban-based pull systems. Simulation is used to establish the performance of the resulting policy vs. two existing policies, for a variety of production scenarios and cost structures. A lower bound on total cost is also established using a simulation-based procedure. In general, early fulfilment with one-for-one replenishment is shown to provide greater benefit than making items to order. Neither of the existing policies, however, was found to use advance demand information as effectively as the proposed approach, which outperformed the existing policies in every case considered. Additionally, the proposed policy has the advantage of both retaining its benefit at high levels of system utilisation and increasing benefit up to the maximum level of advance demand information provided.     

Carrier induced magnetism in dilute Fe doped Ge1−xSbx thin films

Thin films of Fe_0.01Ge_1−xSb_x (x = 0.01, 0.05, 0.10) alloys were prepared by thermal evaporation technique. Characterization of these thin films was done using High Resolution X-Ray Diffraction (HRXRD), Two Probe Resistivity measurement, Atomic Force Microscopy (AFM) and Magnetic Force Microscopy (MFM) respectively. The resistivity results show that activation energy increases with increase in Sb concentration. The low temperature conduction is explained by Variable Range-Hopping mechanism, which fits very well for the whole temperature range. The Arrhenius plot reveals semiconducting behavior. The AFM images of alloys show almost uniform particle size distribution with average particle size varying from 35 to 60 nm with increase in Sb concentration. The MFM images corresponding to the AFM images show the films exhibiting ferromagnetic interactions at room temperature. The average magnetic domain sizes were observed to increase from 43 to 68 nm with increase in Sb concentration from x = 0.01 to x = 0.10.     

A simple and elegant technique connecting Marcuse spot size relations to variational formulations in single-mode fiber characterization

Accurate knowledge of spot size, an important criterion in single-mode fiber optics, is obtained by two different optimization techniques, the well-known variational method and Marcuse formulation. The later is more accurate but cannot predict fiber parameters from given spot sizes. In this study, it is shown for the first time to the best of our knowledge that using simultaneously Marcuse relations of fiber spot sizes for single-mode graded index fibers and also variational formulation, we can more accurately and easily determine the fiber parameters for a particular normalized frequency. Then it is shown with typical example of fractional power in the core that in the case of such fibers, this synthesis of these two useful approaches can also more accurately estimate propagation characteristics of practical interest. This equivalence provides an easy and useful connection between two fundamental but disjoint approaches and should find wide use.