Hydrothermal corrosion of magnesiapartially-stabilized zirconia

Changes in the phase compositions and microstructures of magnesia-partially-stabilized zirconia (Mg-PSZ) were studied in water at 80–300 °C, 1 m HCl solutions at 80–140 °C and 1 m CH₃COOH-CH₃COONa buffer solutions at pH 3 and 80–140 °C for 10–40 days. The tetragonal to monoclinic phase transformation and the degradation of the fracture strength occurred in water above 200 °C. On the other hand, although no noticeable tetragonal to monoclinic phase transformation proceeded in 1 m HCl solutions and 1 m CH₃COOH-CH₃-COONa buffer solutions at pH 3 below 140 °C, the fracture strength of Mg-PSZ greatly degraded. The dissolution of Mg²⁺ ion was observed in water above 200 °C and in 1 m HCl solutions above 80 °C.     

PECVD of diamond-like carbon (a-C:H) from the decomposition of methane in a high-density inductively coupled discharge

The paper describes an experimental investigation of the diamond-like carbon deposition process from methane precursor with an innovative high-density inductively coupled plasma source. It appears that a high plasma density allows a fast growth of diamond-like carbon coatings exhibiting a high hardness. In contrast to what is usually found in the literature, it seems that the ion species participate significantly to the growth of the carbon film when exposed to a high ion flux.     

Real-Time Three-Dimensional Occupancy Grid Modeling for the Detection and Tracking of Construction Resources

Awareness of the construction environment can be improved by automatic three-dimensional (3D) sensing and modeling of job sites in real time. Commercially available 3D modeling approaches based on range scanning techniques are capable of modeling static objects only, and thus cannot model dynamic objects in real time in an environment comprised of moving humans, equipment, and materials. Emerging prototype video range cameras offer an alternative by facilitating affordable, wide field of view, dynamic object tracking at frame rates better than 1?Hz (real time). This paper describes a methodology to model, detect, and track the position of static and moving objects in real time, based on data obtained from video range cameras. Experiments with this technology have produced results that indicate that video rate 3D data acquisition and analysis of construction environments can support effective modeling, detection, and tracking of project resources. This approach to job site awareness has inherent value and broad application. In combination with effective management practices and other sensing techniques, this technology has the potential to significantly improve safety on construction job sites.     

Finite-element analysis and experimental study on tensile fatigue behaviour of bitumen–stone adhesion

Tensile fatigue behaviours of bitumen–stone adhesion were investigated using a dynamic mechanics analyser under stress‐controlled mode at two temperatures of 5 and 25°C and various controlled‐stress levels. Failure characteristics including interfacial failure and cohesive failure were examined using image analysis of fracture surfaces. Finite‐element analysis on stress distributions was conducted under different temperatures, film thickness and interfacial bonding conditions. A Coulomb–Mohr like criterion in combination with shear and normal stresses is proposed to deal with the extreme thin adhesive layer, which can be further simplified into an adhesive zone without significant loss of accuracy for stress analysis.     

Practical Equivalent Continuum Model for Simulation of Jointed Rock Mass Using FLAC3D

A simple practical equivalent continuum numerical model for simulating the behavior of jointed rock mass has been extended to three-dimensional using FLAC3D. This model estimates the properties of jointed rock mass from the properties of intact rock and a joint factor (Jf), which is the integration of the properties of joints to take care of the effects of frequency, orientation, and strength of joint. A new FISH function has been written in FLAC3D specifically for modeling jointed rocks using the Duncan and Chang hyperbolic model. This model has been validated first with simple element tests at different confining pressures for different rocks with different joint configurations. Explicit modeling of the joints has also been done in element tests and results obtained compare well with the results of equivalent continuum model and also with experimental results. Further, this has been applied for a case study of a large underground power house cavern in the Himalayas. The analysis has been done under various stages of excavation, assigning a null model available in FLAC3D for simulating the excavation.     

A high dynamic magnetooptic current transformer with advanced signal processing

In the power industry, current has to be measured for metering and protection purposes. Conventional sensor setups need two transformers to realize the high dynamic range. By the described mixed analog/digital signal processing algorithm, the inherent low photonic noise of the input signals was maintained up to the full sensor output. The system design is based on a rigorous investigation and optimization of the error sources in the signal processing chain. The results are proved by a demonstrator, achieving a dynamic range from 0.05 to 100 times the rated current and a ratio root mean square error of less than 0.5%.     

Numerical solution for shape optimization of an impactor penetrating into a semi-infinite target

The shape of the impactor with the maximum depth of penetration (DOP) for a given impact velocity is found using a numerical procedure for solving a corresponding non-classical variational problem. It is shown that the optimum shape in a general case is close to a blunt cone. The variation of the optimal shape of the impactor and the dependence of the DOP vs. the initial (impact) velocity and friction coefficient is studied. The analysis is performed also for optimal conical impactors.     

Numerical Homogenization Techniques Applied to Growth and Remodelling Phenomena

Materials with inherent microstructures like granular media, foams or spongy bones often show a complex constitutive behaviour on the macroscale while the microscopic constitutive equations may be formulated in a simple fashion. Applying homogenization procedures allows to transfer the information from the microlevel to the macrolevel. In the present contribution the porous structure of hard biological tissues, i.e. of spongy bones, is investigated. On the macroscale the approach is embedded into an extended continuum mechanical setting in order to capture size effects. The constitutive equations are formulated on the microscopic level taking into account growth and reorientation of the microstructural elements. By application of a strain-driven numerical homogenization procedure the macroscopic stress response is obtained.     

Pool boiling on a superhydrophilic surface

Titanium Dioxide, TiO₂, is a photocatalyst with a unique characteristic. A surface coated with TiO₂ exhibits an extremely high affinity for water when exposed to UV light and the contact angle decreases nearly to zero. Inversely, the contact angle increases when the surface is shielded from UV. This superhydrophilic nature gives a self-cleaning effect to the coated surface and has already been applied to some construction materials, car coatings and so on. We applied this property to the enhancement of boiling heat transfer. An experiment involving the pool boiling of pure water has been performed to make clear the effect of high wettability on heat transfer characteristics. The heat transfer surface is a vertical copper cylinder of 17 mm in diameter and the measurement has been done at saturated temperature and in a steady state. Both TiO₂-coated and non-coated surfaces were used for comparison. In the case of the TiO₂-coated surface, it is exposed to UV light for a few hours before experiment and it is found that the maximum heat flux (CHF) is about two times larger than that of the uncoated surface. The temperature at minimum heat flux (MHF) for the superhydrophilic surface is higher by 100 K than that for the normal one. The superhydrophilic surface can be an ideal heat transfer surface. Copyright © 2002 John Wiley & Sons, Ltd.