The measurement of solar array discharges in a simulated spaceenvironment

A spacecraft in a plasma builds up charge on all the dielectric surfaces and interfaces. Once the net charge exceeds the dielectric breakdown of the material, a discharge occurs. One of the more susceptible pieces of equipment is the antenna/receiver system. The radiated E-field may be strong enough to create an ambiguous signal which may be misinterpreted by the system electronics and cause a system malfunction. A technique is developed to monitor the radiated E-field of materials discharging in an electron environment, using vacuum chambers for measuring the material discharges which are made of highly reflective materials. These chambers affect the radiated E-field due to multiple reflections from the walls. The technique developed defines a method for correcting the effects caused by the measurement facilities. The methodology is: monitor the radiated E-field with a broadband dipole antenna, and digitize the radiated signal as a function of time. Determine the frequency response of the radiated E-field using an FFT algorithm. Measure the transmission and reflection characteristics of the two-port network inside the measurement chamber, and determine the impedance network from the measured E-parameters across the frequency band of interest. Transform the measured E-field frequency response through the impedance network to obtain the frequency response of the actual radiated discharge current. Find the inverse FFT of this response to obtain the actual radiated discharge current response. This technique aids in the prediction of the E-field coupling into receive antennas on-board actual satellites     

Crosstalk between microstrip transmission lines

Methods for prediction of crosstalk between microstrip transmission lines are reviewed and simplified for the weak-coupling case. Classical coupled transmission line theory is used for uniform lines, and potential and induced EMF methods are used for crosstalk between nonuniform lines. It is shown that the potential method is equivalent to classical coupled transmission line theory for the case of uniform lines. An experiment was performed for uniform coupled microstrip lines for frequencies from 50 MHz to 5 GHz, and good agreement between theory and measurement was obtained for both near- and far-end crosstalk     

Microscopic simulation of electronic noise in semiconductormaterials and devices

We present a microscopic interpretation of electronic noise in semiconductor materials and two-terminal devices. The theory is based on Monte Carlo simulations of the carrier motion self-consistently coupled with a Poisson solver. Current and voltage noise operations are applied and their respective representations discussed. As application we consider the cases of homogeneous materials, resistors, n⁺nn ⁺ structures, and Schottky-barrier diodes. Phenomena associated with coupling between fluctuations in carrier velocity and self-consistent electric field are quantitatively investigated for the first time. At increasing applied fields hot-carrier effects are found to be of relevant importance in all the cases considered here. As a general result, noise spectroscopy is found to be a source of valuable information to investigate and characterize transport properties of semiconductor materials and devices     

Effects of error variation in means of measurement on reliability parameters in engineering-system monitoring

A method is given for calculating the monitoring reliability parameters (MRP) for an engineering system with allowance for the drift in the measurement error of the means of measurement (MM). The approach is based on introducing a biased MM error distribution into the traditional formulas for the conditional probabilities of spurious and unobserved failure. The bias at the center of the distribution is determined by the systematic error at the given instant. An example is given to illustrate the performance in MRP calculation.Translated from Izmeritel'naya Tekhnika, No. 1, pp. 12–13, January, 1994.     

Suppression control method for torque vibration of three-phase HB-type stepping motor utilizing feedforward control

This paper proposes a method to reduce the vibration of the three-phase HB-type stepping motor with cogging torque by the feedforward compensation control. The compensation signal to suppress the vibration of the motor frame is obtained by the repetitive controller installing an online Fourier transformer and utilizing an acceleration sensor attached to the motor frame or an acoustic sensor such as a microphone placed close to the frame. The sensor is used only for the acquisition of the feedforward compensation data. The feedforward compensation signal at an arbitrary operating point is derived from the amplitude and phase data of the frequency components and the operating point data. Compensation data obtained by the repetitive controller is applied to the operating point changed by reference frequency and load condition in steady state. The compensation signal for the new operating point will be generated from compensation data utilizing polynomial equation approximation and linear interpolation method. The effectiveness of this proposed method is confirmed by the experimental results.     

Drift hole mobility in strained and unstrained doped Si1-xGex alloys

Results of the drift hole mobility in strained and unstrained SiGe alloys are reported for Ge fractions varying from 0 to 30% and doping levels of 10¹⁵-10¹⁹ cm^-3. The mobilities are calculated taking into account acoustic, optical, alloy, and ionized-impurity scattering. The mobilities are then compared with experimental results for a boron doping concentration of 2×10¹⁹ cm^-3. Good agreement between experimental and theoretical values is obtained. The results show an increase in the mobility relative to that of silicon     

Efficient diode-pumped single-frequency erbium:ytterbium fiberlaser

We report a 7.6-mW single-frequency fiber laser operating at 1545 nm, using for the first time an Er³⁺:Yb³⁺ doped fiber and a fiber grating output coupler. The laser did not exhibit self-pulsation, which is a typical problem in short three-level fiber lasers, and had a relative intensity noise (RIN) level below -145.5 dB/Hz at frequencies above 10 MHz. The linewidth of the laser was limited by the relaxation oscillation sidebands in the optical spectrum and was typically less than 1 MHz     

Capacity enhancement of cellular CDMA by traffic-based control ofspeech bit rate

Variable rate speech coding is now recognized as an important system component for high-capacity cellular networks because it exploits speech statistics to reduce the average bit rate, which results in reduced interference and increased capacity. Once a variable rate capability is available, an additional capacity enhancement can be achieved by introducing network control of the user bit rate in response to changing traffic levels. We introduce the concept of network control of rate and propose a particular network-control method for code-division multiple access (CDMA) systems. Based on an M/M/∞//M queueing model applied to a cell under heavy traffic conditions and a new performance measure called averaged speech quality, we obtain simulation results to demonstrate how network control of rate can achieve improved speech quality or increased capacity for a given quality objective     

The apolipoprotein E allele epsilon 4 is overrepresented in patients with the Lewy body variant of Alzheimer's disease

We determined apolipoprotein E (ApoE) genotypes in 122 autopsied demented patients. The frequency of the ApoE epsilon 4 allele was 39.6% in Alzheimer's disease (AD), 29.0% in the Lewy body variant of AD (LBV), and 6.25% in diffuse Lewy body disease. For AD and LBV patients, the epsilon 4 frequency was significantly higher than that reported in nondemented controls (10 to 15%). Therefore, LBV and AD share ApoE epsilon 4 as a genetic risk factor, providing further evidence that these conditions overlap.