Effects of Widmanstätten ferrite on the mechanical properties of a 0.2 pct C-0.7 pct Mn steel

Laboratory melted and rolled C-Mn steel plates were austenitized at either 925 °C or 1150 °C to produce nominal austenite grain sizes of 60 and 200 μm, resspectively. The plates were then cooled at rates in the range of about 2 °C/min to 400 °C/min to produce mixed polygonal ferrite/Widmanst?tten ferrite/pearlite microstructures. The percentage of Widmanst?tten structure (a Widmanst?tten ferrite/pearlite aggregate) increases with increasing prior austenite grain size and cooling rate. Both yield strength and impact toughness increase with decreasing austenite grain size and increasing cooling rate. This simultaneous improvement in strength and toughness is attributed to overall refinement of both the polygonal ferrite and Widmanst?tten structure. Both yield and tensile strength increase with an increase in the volume fraction of Widmanst?tten ferrite and a reduction in ferrite grain size. In contrast, the toughness level achieved in these polygonal ferrite/Widmanst?tten ferrite/pearlite microstructures depends largely on the ferrite grain size; the finer the grain size, the better the toughness.     

Effects of vanadium and processing parameters on the structures and properties of a direct-quenched low-carbon Mo-B steel

The structures and mechanical properties of a series of thermomechanically processed, direct-quenched martensitic 0.1C-1.4Mn-0.5Mo-B steels containing from 0 to 0.24 wt pct va have been investigated and compared to those obtained after a conventional austenitizing-and-quenching treatment. For all processing conditions, vanadium additions to the base composition are found to increase hardenability (ideal critical parameter,D,); the largest effects (up to a 90 pct increase inD _I) are noted when samples are hot-rolled prior to direct quenching. Vanadium additions are also observed to provide significant strengthening in the quenched-and-tempered condition as the result of the precipitation of fine V-Mo carbides. The strengthening increment due to these precipitates is approximately 100 MPa/0.1 wt pct V over the range of vanadium additions examined. At the same time, however, these precipitates reduce notch toughness; on the average, the 20 J transition temperature increases by about 4 °C for each 10 MPa increment in yield strength. For the conditions examined, the best balance of strength and toughness is obtained in direct-quenched samples which are control-rolled(i.e., rolling is completed below the austenite recrystallization temperature) prior to quenching.     

Cognitive and neuropathologic correlates of Stroop Color-Word Test performance in Alzheimer's disease.

The Stroop Color-Word Test (SCWT; C. Golden, 1978) was examined in 59 patients with probable Alzheimer's disease (AD) and in 51 demographically comparable normal control (NC) participants. AD patients produced significantly larger Stroop interference effects than NC participants, and level of dementia severity significantly influenced SCWT performance. Principal -components analyses demonstrated a dissociation in the factor structure of the Stroop trials between NC participants and AD patients, suggesting that disruption of semantic knowledge and speeded verbal processing in AD may be a major contributor to impairment on the incongruent trial. Results of clinicopathologic correlations in an autopsy-confirmed AD subgroup further suggest the invocation of a broad network of integrated cortical regions and executive and language processes underlying successful SCWT performance. (PsycINFO Database Record (c) 2010 APA, all rights reserved)     

Effects of austenite grain size and cooling rate on Widmanstätten ferrite formation in low-alloy steels

Deformation dilatometry is used to simulate the hot rolling of 0.20 pct C-1.10 pct Mn steels over a product thickness range of 6 to 170 mm. In addition to a base steel, steels with additions of 0.02 pct Ti, 0.06 pct V, or 0.02 pct Nb are included in the study. The transformation behavior of each steel is explored for three different austenite grain sizes, nominally 30, 55, and 100 μm. In general, the volume fraction of Widmanst?tten ferrite increases in all four steels with increasing austenite grain size and cooling rate, with austenite grain size having the more significant effect. The Nb steel has the lowest transformation temperature range and the greatest propensity for Widmanst?tten ferrite formation, while the amount of Widmanst?tten ferrite is minimized in the Ti steel (as a result of intragranular nucleation of polygonal ferrite on coarse TiN particles). The data emphasize the importance of a refined austenite grain size in minimizing the formation of a coarse Widmanst?tten structure. With a sufficiently fine prior austenite grain size (e.g., ≤30 μm), significant amounts of Widmanst?tten structure can be avoided, even in a Nb-alloyed steel.     

Fatigue analysis and testing of adhesive joints

The fatigue resistance of a single-lap aluminium adhesive joint to cyclic loading in combined shear and bending mode is investigated by nonlinear finite element analysis and crack propagation experiments. The epoxy adhesive is modelled by an elasto-plastic overlay material model. The initial cycles build up a residual stress state, leading to nearly linear material behaviour in the following cycles. Fatigue crack propagation is modelled by removing adhesive elements. Two series of experiments with one-sided cyclic load were carried out. The crack length was monitored by measuring the bending compliance around the end of the overlap with clip-gauges. The crack length is determined as a simple linear function of the measured compliance. The experiments show nearly constant rate crack growth until failure, with no appreciable crack initiation period. The rate of crack growth is proportional to the stress level to the power m = 6.2. Fatigue life results are given in the form of S---N curves for adhesive thickness of 0.1 and 0.3 mm. There is no systematic influence of the thickness of the adhesive on the fatigue life. This supports the use of a crack propagation and fatigue life criterion formulated in terms of the energy release rate.     

Gold Nanoparticle‐Based Sensors Activated by External Radio Frequency Fields

A novel molecular beacon (a nanomachine) is constructed that can be actuated by a radio frequency (RF) field. The nanomachine consists of the following elements arranged in molecular beacon configuration: a gold nanoparticle that acts both as quencher for fluorescence and a localized heat source; one reporter fluorochrome, and; a piece of DNA as a hinge and recognition sequence. When the nanomachines are irradiated with a 3 GHz RF field the fluorescence signal increases due to melting of the stem of the molecular beacon. A control experiment, performed using molecular beacons synthesized by substituting the gold nanoparticle by an organic quencher, shows no increase in fluorescence signal when exposed to the RF field. It may therefore be concluded that the increased fluorescence for the gold nanoparticle‐conjugated nanomachines is not due to bulk heating of the solution, but is caused by the presence of the gold nanoparticles and their interaction with the RF field; however, existing models for heating of gold nanoparticles in a RF field are unable to explain the experimental results. Due to the biocompatibility of the construct and RF treatment, the nanomachines may possibly be used inside living cells. In a separate experiment a substantial increase in the dielectric losses can be detected in a RF waveguide setup coupled to a microfluidic channel when gold nanoparticles are added to a low RF loss liquid. This work sheds some light on RF heating of gold nanoparticles, which is a subject of significant controversy in the literature.     

Cognitive profiles of mild cognitive impairment with and without vascular disease.

This study examined whether the cognitive profile of subjects with mild cognitive impairment (MCI) with vascular disease differs from that of MCI subjects with no vascular disease. Consecutive MCI subjects with vascular disease (n=60) and matched MCI subjects with no vascular disease (n=60) were included in the study and were compared with healthy control subjects (n=60). The neuropsychological assessment comprised tests of speed and attention, episodic memory, visuospatial function, language, and executive function. Control subjects performed significantly better than did both MCI groups on the neuropsychological battery. MCI subjects with no vascular disease performed better overall than did MCI subjects with vascular disease, most clearly on tests of speed and attention, visuospatial function, and executive function. MCI subjects with and without vascular disease exhibited differences, both in terms of overall performance and of cognitive profiles. These differences can be largely explained by deficits in speed and attention and in executive function of the MCI subjects with vascular disease. (PsycINFO Database Record (c) 2010 APA, all rights reserved)     

Avoiding the Pitfalls of Installing Vertical Market Software

For many companies, vertical market software is the logical choice when individualized information systems are needed. However, both the purchaser and the vendor face certain problems unique to vertical market products, and both must know how to avoid or minimize these impediments to successful systems implementation. In the following article, a hypothetical company history is used to illustrate the pitfalls of the vertical market and ways to avoid them.     

Anion transport processes in the mammalian superficial proximal straight tubule

The experiments reported in this paper were designed to evaluate some of the characteristics of anion transport processes during fluid absorption from superficial proximal straight tubules isolated from rabbit kidney. We measured net chemical C1- flux during fluid absorption from tubules perfused and bathed with Krebs-Ringer buffers containing 113.6 mM C1-, 10 mM acetate, and 25 mM HCO-/3 at pH 7.4; assessed the effects of carbonic anhydrase inhibitors on net fluid absorption in the presence and absence of CO2; and evaluated the influx and efflux coefficients for [14C]-acetate transport at 37degreesC, at 21degreesC, and in the presence of carbonic anhydrase inhibitors. The experimental data shown that, for this nephron segment, net C1- flux accompanies approximately 27.5% of net Na+ absorption; and net C1- absorption may be accounted for by a passive transport process, primarily diffusional in nature. Fluid absorption in this nephron segment is reduced 40-60% by carbonic anhydrase inhibitors, but only when the tubules are exposed to 95% O2-5% CO2 rather than 100% O2. Thus, it seems probably that approximately half of Na+ absorption in these tubules may be rationalized in terms of a carbonic anhydrase-dependent CO2 hydration process. In addition, there may occur in these isolated proximal tubules an acetazolamide-insensitive moiety of HCO-/3 absorption comparable to that observed for proximal tubules in vivo. Finally, we provide evidence that net efflux of luminal acetate is due to metabolic energy-dependent processes other than CO2 hydration and may, under appropriate conditions, account for approximately one-fourth of net Na+ absorption.