Long-term viable bioaerosol sampling using a temperature- and humidity-controlled filtration apparatus,a laboratory investigation using culturable E. coli.

Sampling for culturable (e.g., viable) aerosolized microbes (bioaerosols) is a useful means to provide information for public health monitoring and studies. However, it is challenging to maintain microbe culturability when sampling at high flow rates (>12 L/min) and extended periods of time (≥4 h). We developed a first-generation, viable bioaerosol collection system (VBCS) utilizing temperature (T) and relative humidity (RH)–conditioned filtration at a flow rate of 25 L/min. A two-stage system of tube-in-shell Nafion? exchange units provides cooling to ≤10°C and RH conditioning to 80–95%. Aerosol particles are collected on a polyurethane nanofiber filter providing a physical collection efficiency of >95% for sizes 0.06–10 µm. The T and RH conditions at the collection filter are maintained, despite changes to ambient conditions. The initial testing of the VBCS was done under indoor, laboratory conditions with aerosolized, vegetative E. coli. A scenario of a 30-min challenge of bioaerosol followed by continued sampling of clean air for various times was used to judge culturability maintenance under extended-term sampling. An initial loss of culturability upon collection onto the filter was observed; 23 ± 13% relative to 4-mm all-glass impinger. However once collected, 98% of culturability was maintained for an additional 4.5 h of sampling. An exponential decay in culturability was observed from 8 h to 15 h of sampling. Also, 24-h cold storage of the filters collected was studied. The VBCS is based on the use of dry filter cassettes, needs minimal maintenance, and preserves culturability of vegetative bacteria for >4 h.

© 2017 RTI International and Aerosol Dynamics Inc.     

Rhodium Complexed C2‐PAMAM Dendrimers Supported on Large Pore Davisil Silica as Catalysts for the Hydroformylation of Olefins

Polyamidoamine (PAMAM) dendrimers up to the third generation were grown for the first time on the surface of a large‐pore (18 nm) Davisil silica support. The supported dendrimers of generations 0, 1, 2 and 3 were phosphinomethylated and complexed with rhodium. All the generations were found to be very active for the hydroformylation of olefins. The hydroformylation of 1‐octene was accomplished with a turnover frequency of 1700 h⁻¹ at 70 °C. The G(1) material was found to be the most active when the different generations were compared at 50% conversion at 70 °C     

The questionable role of a microsomal °8 acyl-CoA-dependent desaturase in the biosynthesis of polyunsaturated fatty acids

Several experimental approaches were used to determine whether rat liver and testes express an acyl-CoA-dependent δ8 desaturase. When [1-¹⁴C]5, 11, 14-eicosatrienoic acid was injected via the tail vein, or directly into testes, it was incorporated into liver and testes phospholipids, but it was not metabolized to other labeled fatty acids. When [1-¹⁴C]11, 14-eicosadienoic acid was injected, via the tail vein or directly into testes, or incubated with microsomes from both tissues, it was only metabolized to 5,11, 14-eicosatrienoic acid. When ethyl 5,5,11,11,14,14-d₆-5,11,14-eicosatrienoate was fed to rats maintained on a diet devoid of fat, it primarily replaced esteri-fied 5,8,11-eicosatrienoic acid, but not arachidonic acid. No labeled linoleate or arachidonate were detected. Dietary ethyl linoleate and ethyl 19,19,20,20-d₄-1,2-¹³C-11,14-eicosadienoate were about equally effective as precursors of esterified arachidonate. The doubly labeled 11,14-eicosadienoate was metabolized primarily by conversion to 17,17,18,18-d₄-9,12-ocatdeca-dienoic acid, followed by its conversion to yield esterified arachidonate, with a mass four units greater than endogenous arachidonate. In addition, the doubly labeled substrate gave rise to a small amount of arachidonate, six mass units greater than endogenous arachidonate. No evidence was obtained, with the radiolabeled substrates, for the presence of a δ8 desaturase. However, the presence of an ion, six mass units greater than endogenous arachidonate when doubly labeled 11, 14-eicosa-dienoate was fed, suggests that a small amount of the substrate may have been metabolized by the sequential use of δ8 and δ5 desaturases.     

Wettability of Silica Substrates by Silver–Copper Based Brazing Alloys inVacuo

The sessile drop method has been used to determine the time dependence of the contact angle at 850°C in vacuo for Ag–28 wt% Cu, Ag–35 wt% Cu–1.5 wt% Ti, and Ag–27 wt% Cu–12 wt% In–2 wt% Ti on vitreous and devitrified fused quartz substrates. Nonwetting behavior (θ > 90°) was observed for Ag–28 wt% Cu on both substrates with no evident effect of time at temperature. The silica substrate structure, whether crystalline or amorphous, as well as its surface condition, whether smooth or rough, made no significant difference. In contrast, with Ag–35 wt% Cu–1.5 wt% Ti and Ag–27 wt% Cu–12 wt% In–2 wt% Ti the contact angle continuously decreased with time for both silica substrates, and the structure and surface condition of the substrates had a negligible effect in the case of Ag–27 wt% Cu–12 wt% In–2 wt% Ti, which produced essentially the same contact angles on both silica substrates at a given time of hold at 850°C. The contact angles produced by Ag–35 wt% Cu–1.5 wt% Ti on devitrified fused quartz were consistently higher than those produced on the vitreous substrates, with increasing holding time at 850°C. This is attributable to the presence of extensive cracks in the α-cristobalite layer at the surface of the devitrified substrates, which obstruct wetting and spreading. These results, when correlated with the wettability of preoxidized silicon carbide by the same alloys reported in previous work, could account for the adverse effect on wetting of the high-temperature silica films formed on the surface of the SiC in that work.     

A model for the evaporation of water from large glass particles in pneumatic transport

A model is presented for the evaporation of water from large particles in pneumatic transport. The work is relevant for estimating the coating solution feed rate and the length of the draft tube in Wurster‐type particle coaters. Specifically, the rate of evaporation of water from 1 mm glass particles in a 28.45 mm tube was calculated from the model. The rate increased with solids mass flow rate, inlet air temperature and inlet particle temperature. The heat was more rapidly removed from the particle phase than from the air phase and high inlet air temperatures are tolerated. The model presupposes that the gas and particle velocities, and voidage are known and that the water film on a particle is thin and uniformly distributed. Hydrodynamic considerations that impact on the calculations are discussed.     

Low temperature uniform plastic deformation of metallic glasses during elastic iteration

Molecular dynamics simulations and dynamic mechanical analysis experiments were employed to investigate the mechanical behavior of metallic glasses subjected to iteration deformation in a nominally elastic region. It was found that cyclic deformation leads to the formation of irreversible shear transformation zones (STZs) and a permanent uniform strain. The initiation of STZs is directly correlated with the atomic heterogeneity of the metallic glass and the accumulated permanent strain has a linear relation with the number of STZs. This study reveals a new deformation mode and offers insights into the atomic mechanisms of STZ formation and low temperature uniform plastic deformation of metallic glasses.     

Single‐walled carbon nanotube/poly(methyl methacrylate) composites for electromagnetic interference shielding

Single‐walled carbon nanotube (SWNT)/poly(methyl methacrylate) (PMMA) composites were prepared using coagulation method. The electrical conductivity and the electromagnetic interference (EMI) shielding of SWNT/PMMA composites over the X‐band (8–12 GHz) and the microwave (200–2000 MHz) frequency range have been investigated. The electrical conductivity of composites increases with SWNT loading by 13 orders of magnitude, from 10^?15 to 10^?2 Ω^?1 cm^?1 with a percolation threshold of about 3 wt% SWNTs. The effect of the sample thickness on the shielding effectiveness has been studied, and correlated to the electrical conductivity of composites. The data suggest that SWNT/PMMA composites containing higher SWNT loading (above 10 wt%) be useful for EMI shielding and those with lower SWNT loading be useful for electrostatic charge dissipation. The dominant shielding mechanism of SWNT/PMMA composites was also discussed. POLYM. ENG. SCI., 2009. © 2009 Society of Plastics Engineers     

Changes in the thermophysical properties of microcrystalline cellulose as function of carbonization temperature

Thermophysical properties of carbon materials derived from microcrystalline cellulose have been studied under vacuum and compared with earlier measurements conducted under nitrogen to better understand the influence of porosity, composition, microstructure, and atmosphere effects. The effective thermal conductivity in vacuum is lower than that observed in nitrogen primarily due to the conductivity of nitrogen gas. Radiation effects in both atmospheres were determined to be negligible. Reduction of thermal diffusivity in nitrogen was attributed to the effects of nitrogen gas phonon scattering. The trends for electrical and thermal property changes with structure are similar but not identical due to the differences in electron and phonon transport mechanisms.     

Ferroelasticity in a metal–organic framework perovskite; towards a new class of multiferroics

A metal–organic framework perovskite, [(CH₂)₃NH₂][Mn(HCOO)₃], exhibits a weakly first order ferroelastic phase transition at ～272 K, from orthorhombic Pnma to monoclinic P2₁/n, and a further transition associated with antiferromagnetic ordering at ～8.5 K. The main structural changes, through the phase transition, are orientational ordering of the azetidium groups and associated changes in hydrogen bonding. In marked contrast to conventional improper ferroelastic oxide perovskites, the driving mechanism is associated with the X-point of the cubic Brillouin zone rather than being driven by R- and M-point octahedral tilting. The total ferroelastic shear strain of up to ～5% is substantially greater than found for typical oxide perovskites, and highlights the potential of the flexible framework to undergo large relaxations in response to local structural changes. Measurements of elastic and anelastic properties by resonant ultrasound spectroscopy show some of the characteristic features of ferroelastic materials. In particular, acoustic dissipation below the transition point can be understood in terms of mobility of twin walls under the influence of external stress with relaxation times on the order of ～10^?7 s. Elastic softening as the transition is approached from above is interpreted in terms of coupling between acoustic modes and dynamic local ordering of the azetidium groups. Subsequent stiffening with further temperature reduction is interpreted in terms of classical strain–order parameter coupling at an improper ferroelastic transition which is close to being tricritical. By way of contrast, there are no overt changes in elastic or anelastic properties near 9 K, implying that any coupling of the antiferromagnetic order parameter with strain is weak or negligible.     

CATALYTIC CRACKING OF RESIDUAL PETROLEUM FRACTIONS

ABSTRACT

Arabian Light crude oil vacuum bottoms has been fractionated into five high-boiling fractions by wiped film evaporation, and the fractions subjected to catalytic cracking in a fixed-fluidized bed using a commercial equilibrium cracking catalyst. Density, aromaticity, and heteroatom content generally increased with boiling point, as did metals content except for vanadium and iron which demonstrated possible bimodal distributions. The cracking response of these fractions showed increasing yields of dry gas and coke, with decreasing gasoline yields, as a function of increasing apparent boiling point as would normally be expected. Surprisingly, however, local maxima were observed for wet gas yield and total conversion, with local minima for cycle oil and slurry yields, in the region of the 1200–1263°F (650–680°C) middle fraction. All fractions showed significant response to cracking, with coke yields generally being the only negative factor observed.