Fibre-optic based confocal scanning microscopy with semiconductor laser excitation and detection

A compact novel form of confocal scanning microscope using a semiconductor laser is described. Confocal operation is ensured by the use of a single mode optical fibre for both launching the light into the microscope and collecting the signal from the object. The collected light is allowed to reenter the laser and the image is detected as a modulation on the signal from the laser power monitor diode.<>     

Impact of growth rate on the quality of ZNS-MQW InGaAsP/InP laser structures grown by LP-MOVPE

We investigated the influence of the growth rate on the quality of zero-net-strained InGaAsP/InGaAsP/InP multiquantum well structures for 1.55 μm emission grown by low pressure metalorganic vapor phase epitaxy. The samples consisted of fixed compressive strained wells (ɛ=+1%) and tensile strained barriers (ɛ=−0.5%) grown with different quaternary bandgap wavelengths (λ_B=1.1–1.4 μm). Using higher growth rates, we obtained for the first time high quality zero net strained multi quantum well structures, regardless having constant group V composition in the well and barriers. The samples were analyzed by x-ray diffraction, photoluminescence and atomic force microscopy techniques. The amplitude of surface modulation roughness along [011] direction decreased from 20 nm to 0.53 nm with increasing growth rate and/or quaternary compositions grown outside the miscibility gap. A new deep PL broad emission band strongly correlated with the onset of wavy layer growth is also reported. Broad area and ridge waveguide lasers with 10 wells exhibited low losses (34 cm⁻¹) and low threshold current densities at infinite cavity length (1020 A·cm⁻² and 1190 A·cm⁻², respectively).     

Manufacturing ultra fine line PBGA substrates in a PWB factory

The industry trends for PBGA substrates are smaller and smaller features to support more input/output (I/O) in less space. Packaging technologies such as fine pitch wire bonding and flip chip attach are driving the circuit features to tighter dimensions, both narrower lines and smaller spaces. Many PWB factories are now producing laminate substrates and have exercised more stringent process controls to build finer circuit patterns. Even with the improved process controls, however, the conventional PWB processes and materials cannot achieve the 1 mil lines and 1 mil spaces that are required. Changes in processing and or materials and design are required to make the jump from 3 mil circuit features which are characteristic of leading edge PWB technology to the 1 mil circuit features needed for the newer laminate substrates. Because of our experience with ceramic substrates and the availability of a manufacturing facility that is capable of circuitizing truly fine features, we decided to launch a development effort to define how to build ultra fine line PBGA substrates. In this paper we describe the changes in tooling and in processes that were necessary to move between a conventional PWB facility, which is designed to process 20 in×24 in panels, and a ceramic substrate factory, which is designed to process 3 in×5 in cards. We will also describe the processing changes that need to be implemented to circuitize fine line features in foil copper, typical of the PWB facility, rather than thin, sputtered copper which was used in the ceramic substrate factory. In addition we will offer bond and assembly results and reliability stressing results that demonstrate that the PBGA substrates that we built in this hybrid factory are both functional and reliable     

Texture characterization of Cu interconnects with different Ta-based sidewall diffusion barriers

X-ray diffraction is used to assess the texture of narrow lines and study the impact of different sidewall diffusion barrier materials. All the Ta-based barriers developed a strong 〈1 1 1〉 texture in the scaled geometry, with little effect from sidewall growth. Comparisons were made with blanket wafers, demonstrating the pined grain structure in the narrow lines and contrasting change in texture due to re-crystallization in the unconstrained film. Furthermore, patterned lines showed significant anti-symmetric plane distribution influenced by high strains and twinning along the lines.     

Performance Evaluation of a Novel Converged Architecture for Digital-Video Transmission Over Optical Wireless Channels

A robust channel coding architecture for multigigabit-per-second digital-video transmission over the optical wireless channel is introduced and evaluated. The proposed scheme combines low-density parity-check coding with channel interleaving to improve the transmission over turbulent temporally correlated optical wireless channels while satisfying real-time video delay constraints. Frame error rates of the presented code design are evaluated via simulation for intensity-modulation/direct-detection optical wireless links in both lognormal- and Rayleigh-fading channels. Results indicate that the performance of the proposed system is effective across a large range of atmospheric turbulence strengths and achieves significant temporal diversity in moderately long (10 ms) temporal correlation times while satisfying a 0.3-s real-time delay constraint. Moreover, the proposed design is shown to outperform the Reed-Solomon codes prevalent in the legacy fiber and wireless digital-television distribution systems.     

Magnetic properties of Co- and Mn-implanted BaTiO3, SrTiO3 and KTaO3

Implantation of Co or Mn into single-crystal BaTiO₃(K), SrTiO₃ or KTaO₃(Ca), followed by annealing at 700 °C, produced ferromagnetic behavior over a broad range of transition metal concentrations. For BaTiO₃, both Co and Mn implantation produced magnetic ordering temperatures near 300 K with coercivities 70 Oe. The M–T plots showed either a near-linear decrease of magnetization with increasing temperature for Co and a non-Brillouin shaped curve for Mn. No secondary phases were detected by high-resolution X-ray diffraction. The same basic trends were observed for both SrTiO₃ and KTaO₃, with the exception that at high Mn concentrations (5 at.%) the SrTiO₃ was no longer ferromagnetic. Our results are consistent with recent reports of room temperature ferromagnetism in other perovskite systems (e.g. LaBaMnO₃) and theoretical predictions for transition metal doping of BaTiO₃ [Nakayama et al., Jap. J. Appl. Phys. 40 (2001) L1355].     

Electrical polarization control of vertical-cavity surface-emittinglasers using polarized feedback and a liquid crystal

We report electrical control of the polarization state of a vertical-cavity surface-emitting laser (VCSEL), The VCSEL is subject to strong external optical feedback (up to 6% of emission), with polarization controlled by a liquid-crystal (LC) element, It is found that the contrast ratio of the complete system can be enhanced compared to the contrast ratio of the LC element alone     

Experimental Study of Planar Finite Grid Oscillator Arrays

Results of an experimental study on finite grid oscillator arrays and the effects of the edge element loading stubs in such arrays are presented. Three finite grid oscillator arrays, based on the same unit cell, with different number of unit were fabricated on RT/Duroid 5870 substrate and tested in terms of the oscillation frequencies, radiated power and radiation patterns. It is observed that the oscillation frequency of a finite grid array differs from the theoretically prediction based on the infinite array assumption and is strongly affected by the edge element loading stubs. The measurement also indicates that mode-jumping and multi-frequency (spurious) oscillation can exist in grid oscillator arrays.     

A fast iterated conditional modes algorithm for water-fat decomposition in MRI

Decomposition of water and fat in magnetic resonance imaging (MRI) is important for biomedical research and clinical applications. In this paper, we propose a two-phased approach for the three-point water-fat decomposition problem. Our contribution consists of two components: 1) a background-masked Markov random field (MRF) energy model to formulate the local smoothness of field inhomogeneity; 2) a new iterated conditional modes (ICM) algorithm accounting for high-performance optimization of the MRF energy model. The MRF energy model is integrated with background masking to prevent error propagation of background estimates as well as improve efficiency. The central component of our new ICM algorithm is the stability tracking (ST) mechanism intended to dynamically track iterative stability on pixels so that computation per iteration is performed only on instable pixels. The ST mechanism significantly improves the efficiency of ICM. We also develop a median-based initialization algorithm to provide good initial guesses for ICM iterations, and an adaptive gradient-based scheme for parametric configuration of the MRF model. We evaluate the robust of our approach with high-resolution mouse datasets acquired from 7T MRI.     

5-GHz 32-bit integer execution core in 130-nm dual-V/sub T/ CMOS

A 32-bit integer execution core containing a Han-Carlson arithmetic-logic unit (ALU), an 8-entry /spl times/ 2 ALU instruction scheduler loop and a 32-entry /spl times/ 32-bit register file is described. In a 130 nm six-metal, dual-V/sub T/ CMOS technology, the 2.3 mm/sup 2/ prototype contains 160 K transistors. Measurements demonstrate capability for 5-GHz single-cycle integer execution at 25/spl deg/C. The single-ended, leakage-tolerant dynamic scheme used in the ALU and scheduler enables up to 9-wide ORs with 23% critical path speed improvement and 40% active leakage power reduction when compared to a conventional Kogge-Stone implementation. On-chip body-bias circuits provide additional performance improvement or leakage tolerance. Stack node preconditioning improves ALU performance by 10%. At 5 GHz, ALU power is 95 mW at 0.95 V and the register file consumes 172 mW at 1.37 V. The ALU performance is scalable to 6.5 GHz at 1.1 V and to 10 GHz at 1.7 V, 25/spl deg/C.