Development of smart composite structures with small-diameter fiber Bragg grating sensors for damage detection: Quantitative evaluation of delamination length in CFRP laminates using Lamb wave sensing

The authors and Hitachi Cable, Ltd. have recently developed small-diameter optical fiber and its fiber Bragg grating (FBG) sensor for embedment inside a lamina of composite laminates without strength reduction. The outside diameters of the cladding and polyimide coating are 40 and 52 μm, respectively. First, a brief summary is presented for applications of small-diameter FBG sensors to damage monitoring in composite structures. Then, we propose a new damage detection system for quantitative evaluation of delamination length in CFRP laminates using Lamb wave sensing. In this system, a piezo-ceramic actuator generates Lamb waves in a CFRP laminate. After the waves propagate in the laminate, transmitted waves are received by an FBG sensor attached on or embedded in the laminate using a newly developed high-speed optical wavelength interrogation system. This system was applied to detect interlaminar delamination in CFRP cross-ply laminates. When the Lamb waves passed through the delamination, the amplitude decreased and a new wave mode appeared. These phenomena could be well simulated using a finite element analysis. From the changes in the amplitude ratio and the arrival time of the new mode depending on the delamination length, it was found that this system could evaluate the delamination length quantitatively. Furthermore, small-diameter FBG sensors were embedded in a double-lap type coupon specimen, and the debonding progress could be evaluated using the wavelet transform.     

Avoiding Routing Loops on the Internet

Suppose that some particular link in the Internet is currently congested. A natural solution is to try to make packets bypass that link. This can be done by increasing the cost of that link intentionally, say from a ₁ to a ₂, since the Internet uses shortest-path routing. Unfortunately, however, this often causes temporary loops for packet traveling, called routing loops. In this paper we show that routing loops can be avoided by increasing the cost of the link not directly from a ₁ to a ₂ but through an intermediate value, a ₃, i.e., from a ₁ to a ₃ and then to a ₂. We may need several intermediate values. We show that in this case the greedy strategy, namely, raising the cost as much as possible in each step, is optimal.     

A novel cleaning method of gold-coated atomic force microscope tips for their chemical modification

For chemical modification of gold-coated AFM tips with thiol or sulfide compounds, a new two-step precleaning procedure was studied. The two-step cleaning procedure involves (i) oxidation of organic contaminants on the AFM tips with ozone treatment and (ii) reduction of the oxidized gold surface by immersing the oxidized tip into pure hot ethanol at ca. 65 degrees C. The chemically modified tips prepared from gold-coated AFM tips precleaned by the two-step procedure gave almost the same tip characteristics as those chemically modified immediately after gold vapor deposition in a factory. The present two-step cleaning procedure can be used widely for chemical modification of commercially available gold-coated AFM tips with thiol or disulfide compounds for chemical force microscopy.     

Modeling the effect of statistical variations in length and diameter of randomly oriented CNTs on the properties of CNT reinforced nanocomposites

A nano-mechanical model has been developed to calculate the tensile modulus and the tensile strength of randomly oriented short carbon nanotubes (CNTs) reinforced nanocomposites, considering the statistical variations of diameter and length of the CNTs. According to this model, the entire composite is divided into several composite segments which contain CNTs of almost the same diameter and length. The tensile modulus and tensile strength of the composite are then calculated by the weighted sum of the corresponding modulus and strength of each composite segment. The existing micro-mechanical approach for modeling the short fiber composites is modified to account for the structure of the CNTs, to calculate the modulus and the strength of each segmented CNT reinforced composites. Multi-walled CNTs with and without inter-tube bridging have been considered. Statistical variations of the diameter and length of the CNTs are modeled by a normal distribution. Simulation results show that CNTs inter-tube bridging, length and diameter affect the nanocomposites modulus and strength. Simulation results have been compared with the available experimental results and the comparison concludes that the developed model can be effectively used to predict tensile modulus and tensile strength of CNTs reinforced composites.     

Determination of number-average and weight-average molecular weights of polymer sample from diffusion and sedimentation velocity measurements in theta solvent

Several methods to determine number-average molecular weight M_n and weight-average molecular weight M_w, of a polymer sample are proposed from diffusion and sedimentation velocity measurements at the θ point. According to these methods, M_n and M_w are determined from the diffusion constant vs. molecular weight relationship, and also from the equations of Svedberg and Flory–Mandelkern, using the 2nd-order and the –2nd-order diffusion constants. These methods have been applied to four samples of polydisperse polystyrene in the θ solvent, cyclohexane at 35°C. It was experimentally ascertained that M_n and M_w of each sample determined by the present methods were in good agreement with the results of column fractionation, light scattering, and calculated values from molecular weight distribution curve within experimental errors. It is concluded that the present methods are useful for determining M_n and M_w, since the reliabilities of M_n and M_w values, which are fundamental quantities of polymer characterization, can be raised by comparing the experimental data observed by conventional methods such as osmotic pressure, light scattering, and the Archibald method with those observed by the present methods.     

Source identification of nitrous oxide on autotrophic partial nitrification in a granular sludge reactor

Emission of nitrous oxide (N₂O) during biological wastewater treatment is of growing concern since N₂O is a major stratospheric ozone-depleting substance and an important greenhouse gas. The emission of N₂O from a lab-scale granular sequencing batch reactor (SBR) for partial nitrification (PN) treating synthetic wastewater without organic carbon was therefore determined in this study, because PN process is known to produce more N₂O than conventional nitrification processes. The average N₂O emission rate from the SBR was 0.32 ± 0.17 mg-N L⁻¹ h⁻¹, corresponding to the average emission of N₂O of 0.8 ± 0.4% of the incoming nitrogen load (1.5 ± 0.8% of the converted NH₄⁺). Analysis of dynamic concentration profiles during one cycle of the SBR operation demonstrated that N₂O concentration in off-gas was the highest just after starting aeration whereas N₂O concentration in effluent was gradually increased in the initial 40 min of the aeration period and was decreased thereafter. Isotopomer analysis was conducted to identify the main N₂O production pathway in the reactor during one cycle. The hydroxylamine (NH₂OH) oxidation pathway accounted for 65% of the total N₂O production in the initial phase during one cycle, whereas contribution of the NO₂⁻ reduction pathway to N₂O production was comparable with that of the NH₂OH oxidation pathway in the latter phase. In addition, spatial distributions of bacteria and their activities in single microbial granules taken from the reactor were determined with microsensors and by in situ hybridization. Partial nitrification occurred mainly in the oxic surface layer of the granules and ammonia-oxidizing bacteria were abundant in this layer. N₂O production was also found mainly in the oxic surface layer. Based on these results, although N₂O was produced mainly via NH₂OH oxidation pathway in the autotrophic partial nitrification reactor, N₂O production mechanisms were complex and could involve multiple N₂O production pathways.     

用于先进PCB制造工艺的叠层封装

在20世纪90年代,球栅阵列封装(BGA)和芯片尺寸封装(CSP)在封装材料和加工工艺方面达到了极限。这2种技术如同20世纪80年代的表面安装器件(SMD)和70年代通孔安装器件(THD)一样,在电学、机械、热性能、尺寸、质量和可靠性方面达到最大值。目前,三维封装正在成为用于未来采用的先进印制板(PCB)制造工艺的下一个阶段。它们可以分为圆片级封装、芯片级封装、和封装面。叠层封装(PoP)是一种封装面叠层封装类型的三维封装技术[15]。     

Fischer–Tropsch synthesis over Co–SiO2 catalysts prepared by the sol–gel method

Fischer–Tropsch synthesis was carried out in slurry phase over uniformly dispersed Co–SiO₂ catalysts prepared by the sol–gel method. When 0.01–1 wt.% of noble metals were added to the Co–SiO₂ catalysts, a high and stable catalytic activity was obtained over 60 h of the reaction at 503 K and 1 MPa. The addition of noble metals increased the reducibility of surface Co on the catalysts, without changing the particle size of Co metal significantly. High dispersion of metallic Co species stabilized on SiO₂ was responsible for stable activity. The uniform pore size of the catalysts was enlarged by varying the preparation conditions and by adding organic compounds such as N,N-dimethylformamide and formamide. Increased pore size resulted in decrease in CO conversion and selectivity for CO₂, a byproduct, and an increase in the olefin/paraffin ratio of the products. By modifying the surface of wide pore silica with Co–SiO₂ prepared by the sol–gel method, a bimodal pore structured catalyst was prepared. The bimodal catalyst showed high catalytic performance with reducing the amount of the expensive sol–gel Co–SiO₂.     

Insulation characteristics and its evaluation method of N2 gas for nonstandard lightning impulse waveforms

Until recently, SF₆ gas has widely been used as the best insulating medium in substation equipment. However, SF₆ gas was specified to be a greenhouse gas at COP3 in 1997 because of its high global warming potential (GWP), and alternative insulation gases to SF₆ have been sought for a long time. Alternatives using the natural gases are considered to be suitable, but none of them show better properties for insulation as well as good environmental compatibility. Therefore, it is necessary to rationalize the equipment insulation level and reduce the test voltage of electric power apparatus to as low a level as possible. The actual lightning surge waveform (so‐called nonstandard lightning impulse waveform) occurring in the actual field is different from the standard lightning impulse waveform (1.2/50 μs). There are many cases in which the actual lightning surge waveform has a steep rise and large decay of overvoltage, and the insulation requirements are not as severe as those for the standard lightning impulse waveform. In this paper, we focused our research on N₂ gas as an SF₆ substitute and investigated the insulation characteristics of N₂ gas for a single‐frequency oscillatory waveform with various frequencies from 2.7 to 20.0 MHz and damping ratios. Based on the experimental results, it might be possible to reduce the test voltage of N₂ gas insulation by evaluating the crest value of the actual lightning surge waveform that has been converted into an equivalent standard lightning impulse waveform. © 2009 Wiley Periodicals, Inc. Electr Eng Jpn, 167(2): 10–20, 2009; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.20754     

Effect of casting method on castability of titanium and dental alloys

Titanium, once considered to be difficult to cast because of its relatively high melting point and strong chemical affinity, can now be acceptably cast using newly developed casting apparatus. The objectives of this study were to examine the castability of commercially pure (CP) titanium using an ultra high-speed centrifugal casting machine and a pressure difference-type casting unit and to compare the castability of titanium with that of conventional dental casting alloys. To determine castability, two types of patterns were used: a mesh pattern of 22 × 24 mm cut polyether thread sieve, and a saucer pattern (24 mm diameter) perforated to create four T-shaped ends. The casting equipment significantly affected the mold filling of both patterns . The castability indices obtained from both patterns of CP titanium cast in the centrifugal casting machine were significantly better than the indices of the castings produced in the pressure-difference casting unit. The radiographs of the saucer pattern cast in the centrifugal casting machine showed some pores that were fewer and smaller in size than the pores found in castings made in the pressure-difference unit. When the ultra high-speed centrifugal casting machine was used with the manufacturers recommended mold material, the castability of titanium was similar to that of gold alloy or Ni-Cr alloy cast by conventional means.