Shear rate dependence of viscosity and first normal stress difference of LCP/PET blends at solid and molten states of LCP

The liquid crystalline polymer (LCP) and polyethylene terephthalate (PET) were blended in an elastic melt extruder to make samples having 20, 40, 60, 80, and 100 wt % of LCP. Morphology of these samples was studied using scanning electron microscopy. The steady state shear viscosity (η), dynamic complex viscosity (η*) and first normal stress difference (N₁) were evaluated and compared at two temperatures: 265°C, at which LCP was in solid state, and 285°C, at which LCP was in molten state. The PET was in molten state at both the temperatures. The shear viscosity of the studied blends displayed its dependence on composition and shear rate. A maxima was observed in viscosity versus composition plot corresponding to 80/20 LCP/PET blend. The N₁ increased with LCP loading in PET and with the increased asymmetry of LCP droplets. The N₁ also varied with the shear stress in two stages; the first stage demonstrated elastic deformation, whereas second stage displayed dominant plastic deformation of LCP droplets. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 104: 2212–2218, 2007     

Effects of preparation conditions on the surface modification and performance of polyethersulfone ultrafiltration membranes

The impact that some membrane preparation steps had on ultrafiltration (UF) membrane characteristics and performance was studied. Polyethersulfone (PES) was employed as base polymer, while N‐methyl pyrrolidone (NMP) was used as a solvent, and polyvinylpyrrolidone (PVP) was used as a nonsolvent pore‐forming additive. The manufacturing variables studied were solvent evaporation time and membrane surface modification, using a fluorine‐based copolymer referred to as surface‐modifying macromolecule (SMM). The flat sheet membranes, prepared via phase inversion, were characterized using solute transport data, X‐ray photoelectron spectroscopy (XPS), and contact angle measurements. Membrane performance was evaluated via filtration test protocol that included a 6‐day filtration of concentrated river water. The flux reduction with time was modeled using single and dual mechanisms of fouling. The pore blockage/cake filtration model described better the behavior of the permeation rate along the experiments. Increasing the solvent evaporation time decreased the size of the pores and the permeation rate. However, it did not significantly affect the removal of the organic compounds naturally present in the river water used as feed. XPS and contact angle measurements proved that the short evaporation periods did not allow enough SMM migration to the surface to provoke a significant effect on the membrane performance. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci, 2006     

EFFECT OF NONSOLVENT ADDITIVES ON THE PORE SIZE AND THE PORE SIZE DISTRIBUTION OF AROMATIC POLYAMIDE RO MEMBRANES

In this paper discussions are made on the effect of nonsolvent swelling agents on the average pore size and pore size distributions at the surface of polyamide membranes which result from casting solutions involving above nonsolvent swelling agents.

The size of the polymer aggregate in the film casting solution and the size of polymer network pores are correlated to physicochemical data of ions which constitute the electrolytes used as nonsolvent swelling agents. As such ionic properties the charge density and the free energy of transition of ions from polyamide phase to water phase were considered. The validity of the correlation is limited in a range of casting solution composition where the polymer concentration in the casting solution is close to the limiting concentration of polymer at the phase boundary and the molar ratio of the nonsolvent swelling agent to the amide group involved in the polyamide polymer is equal to or slightly more than 0.7.     

Structural study of hexane-soluble products from hydroliquefaction of three Yallourn brown coal lithotypes over molten salt catalysts

The hexane-soluble fractions of hydroliquefied products from three Yallourn brown coal lithotypes have been separated into five fractions by combined silica-alumina packed column chromatography. Analyses of various fractions by g.c.-m.s. permitted the identification of ≈50 components in the saturate fraction and 40 components in the diaromatic fraction, together with 30 components in the monoaromatics. The components identified were quite similar among hexane-soluble portions of all three lithotypes. A marked predominance of even carbon number alkane (C₂₃-C₂₉) was observed in the hydrocarbon fractions from pale lithotype over $\text{ZnCl}{}_2\text{KCl}$, and medium light lithotype over both pure ZnCl₂ and $\text{ZnCl}{}_2\text{KCl}$. However, medium dark lithotype over both melt catalysts produced a saturate fraction with an odd carbon number(C₂₂-C₂₈) preference. Based on spectral methods, Soxhlet extracts obtained from untreated lithotypes (hexane and benzene solubles) were characterized as complex mixtures of higher molecular weight(300–1000) aliphatic hydrocarbons, which were supposed to be a precursor of the saturates produced from the corresponding lithotype in the catalytic hydroliquefaction.     

Skeletonized hybrid liposomes

Summary Giant hybrid liposomes of polymerizable lipid and cholesterol were prepared by the hydration method and were polymerized by UV irradiation. The obtained giant liposomes were freeze-dried and washed with chloroform to skeletonize the frame structure of the polymerized membrane. The skeletonized liposomes were directly confirmed by scanning electron microscopy. The single-layered and fully spherical liposome frame were easily confirmed by the stereo-pair of the obtained micrographs.     

Cationic copolymerization behavior of a bicyclic orthoester having hydroxy group with glycidyl phenyl ether and volume change on their copolymerization

This article describes cationic ring‐opening copolymerization of a bicyclic orthoester having hydroxy group (BOE‐OH) and glycidyl phenyl ether (GPE), and the volume shrinkage behavior during the copolymerization. THF soluble polyethers [poly(BOE‐OH‐co‐GPE)] were obtained by the copolymerizations at 80–180°C, while crosslinked poly(BOE‐OH‐co‐GPE) was obtained by the copolymerizations at 220–250°C. This crosslinking reaction may originate from the dehydration of methylol groups in the side chain of poly(BOE‐OH‐co‐GPE). The volume shrinkage during the cationic copolymerization reduced as the increase of the BOE‐OH feed ratio. By contrast, the volume shrinkage on the crosslinking polymerization was almost independent on the BOE‐OH feed ratio. Poly(BOE‐OH‐co‐GPE)s with higher BOE‐OH composition showed lower thermal weight loss temperature owing to the release of H₂O by dehydration of methylol groups. The BOE‐OH component in the THF soluble poly(BOE‐OH‐co‐GPE)s lowered the glass transition temperature (T_g), while that in the crosslinked poly(BOE‐OH‐co‐GPE) increased the T_g probably because of the higher crosslinking density. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 1356–1361, 2006     

Synthesis of poly(tetrahydrofuran-b-ε-caprolactone) macromonomer via the Sml2-induced transformation

Summary A novel well-defined macromonomer consisting of different types of monomers in polymerization mechanisms was synthesized for the first time through the SmI₂-induced transformation. The macromonomer, -methacryloylpoly-(tetrahydrofuran-b--caprolactone), was prepared by the reaction of methacryloyl chloride with living poly(tetrahydrofuran-b--caprolactone) [poly(THF-b-CL)] which was obtained by the two-electron reduction of the cationic growing center of poly(THF) by samarium iodide (SmI₂) followed by the polymerization of CL. ¹H NMR analysis indicated the quantitative introduction of the methacryloyl group onto the polymer end. The molecular weight distribution of the macromonomer was relatively narrow, and the unit ratio of THF to CL could be controlled by both polymerization time of THF and the amount of CL, resulting from the living nature of both CL- and THF-polymerizations. Radical copolymerization of the produced macromonomers with methyl methacrylate in the presence of AIBN resulted in a polymethacrylate backbone grafted with poly(THF-b-CL) block copolymers.     

Rearrangement of the main chain of the organocobalt polymers

The polymers 3 having pyridine moieties in the main chain were synthesized by the reaction of the organocobalt polymers 1 having cobaltacyclopentadiene moieties in the main chain with various nitriles 2. When brown colored 1 and excess 2 were heated in tetrahydrofuran at 80 °C for 24 h and then at 150 °C for 12 h in a sealed tube, the polymers 3 were obtained by the precipitation with methanol in good yields. From the spectroscopic measurements, the resulting polymers 3 were found to contain 35 – 90% of the pyridine moieties depending on the structures of 1. Received: 7 July 1997/Revised: 14 August 1997/Accepted: 25 August 1997     

Synthesis of cationic flocculant by radiation-induced copolymerization of methyl chloride salt of N,N-dimethylaminoethyl methacrylate with acrylamide in aqueous solution

The radiation-induced copolymerization of the methyl chloride salt of N,N-dimethylaminoethyl methacrylate (DMAEM·MC) with acrylamide (AAm) was used to prepare a cationic polymer flocculant. The polymerization rate increased with increasing dose rate, polymerization temperature, monomer concentration and mole fraction of AAm in the monomer mixture. The molecular weight of the copolymer was also found to increase with monomer concentration and mole fraction of AAm, but at high concentration and fraction of AAm, intermolecular crosslinking tends to occur during the polymerization to form water-insoluble copolymer. A water-soluble copolymer having various molecular weights and cationic strengths can be synthesized by selecting suitable reaction conditions; i.e., this radiation process can provide a much higher molecular weight copolymer with a wide range of cationic strength. The flocculation effect was evaluated using sludge from wastewater of sugar manufacture. It was found that the radiation-polymerized copolymer DMAEM·MC–AAm has an excellent flocculation effect.     

Development of a high‐resolution RGBW flexible display using a white organic light‐emitting diode with microcavity structure and that of a side‐roll touch panel

In this study, white organic electroluminescent devices with microcavity structures were developed. A flexible high‐resolution active‐matrix organic light‐emitting diode display with low power consumption using red, green, blue, and white sub‐pixels formed by a color‐filter method was fabricated. In addition, a side‐roll touch display was developed in combination with a capacitive flexible touch screen.