The oxidative coupling of methane on alkali- and alkaline earth-phosphate catalysts

The oxidative coupling of methane has been tested over alkali- and alkaline earth-phosphate catalysts at 700 and 775 °C with and without the introduction of a small quantity of tetrachloromethane (TCM) to the feedstream. In general, the conversion of methane was enhanced by the addition of TCM but the effect on selectivity was dependent on the catalyst being examined. The selectivity to C₂ and higher hydrocarbons and that to oxidation products have been shown to have a dependence on the cation radius/charge ratio.     

A model for the complex permittivity of water at frequencies below 1 THz

Experimental permittivity data of liquid water, compiled from the open literature, were selectively applied to support a modeling strategy. Frequencies up to 1 THz and atmospheric temperatures are covered with an expression made up by two relaxation (Debye) terms. The double-Debye model reduces to one term when the high frequency limit is set at 100 GHz, and the model can be extended to 30 THz by adding two resonance (Lorentzian) terms. The scheme was carried out by employing nonlinear least-squares fitting routines to data we considered reliable.     

Spatial distribution of silica fillers in phase-separated rubber blends investigated by three-dimensional elemental mapping

The distribution of nano-sized silica in binary rubber blends is characterized by scanning transmission electron microscopy (STEM) tomography combined with energy dispersive X-ray spectrometry (EDX). 3D distribution of silica is visualized by STEM-EDX tomography with the tilt-series of silicon elemental maps, while the phase-separated morphologies of polyisoprene rubber (IR) and styrene-butadiene rubber (SBR) are visualized by STEM-tomography in high-angle-annular-dark field (HAADF) mode. The combination of STEM-EDX and STEM-HAADF tomography enables us to determine the distribution of silica between the two rubber phases quantitatively even with high contents of silica up to 70 phr (weight parts per hundred rubber). It is found that silica is preferentially distributed in the SBR phase, but it is also distributed in the IR phase when the IR fraction in the total rubber components is higher than 40 wt%. The preferential distribution of silica in the SBR phase improves the dispersion of the IR domains. This is the first use of this technique for a multicomponent polymer system, showing the advantage to characterize the complicated multicomponent polymer composite morphologies.     

Quantitative determination of corrosion products and adsorbed water on copper in humid air containing SO2 by IR-RAS measurements

The time dependency of the amounts of corrosion products and co-existing adsorbed water on copper in humid air containing SO₂ was estimated from a series of in situ time-resolved IR-RAS spectra on the basis of the relations between the band intensities and the mass changes of the corrosion products, which were determined by simultaneous measurement of IR-RAS and QCM. The amounts of both corrosion products increased slowly at the initial stage and later increased rapidly. Although the relative humidity was kept constant, the amount of adsorbed water increased nearly the same behavior as that of corrosion products in the stage of relatively small amounts of corrosion products and later increased rapidly when the amounts of corrosion products increased. In humid air without SO₂, sulfite gradually decomposed and some of it changed into sulfate.     

Optimum combination of operating parameters in abrasive cut-off

For optimization of abrasive cut-off operation, wheel wear equation must be identified before the operation is optimized. The equation is obtained by using GMDH algorithm with successive determination of trends containing interactive terms. In the model equation factors of grinding fluid are taken into consideration in addition to the factors of wheel, work material, feed (table speed) and wheel speed. For the identification of the model wheel wear tests are performed under the experimental design treating the above-mentioned factors as independent variables. The grinding ratio (output in the model) can be predicted for combinations of various factors using the model. With the wheel wear equation and machining cost model, the optimum combination of wheel, fluid, feed and wheel speed can be selected for a given work material. The relationships between these variables and the costs are investigated.     

Development of low thermal expansion superalloy

Alloy 903 and Alloy 909 are well-known Fe-Co-Ni-Al-Ti-Nb alloys with controlled low thermal expan-sion, but they have some properties that can be improved. To improve stress-accelerated grain boundary oxidation embrittlement of Alloy 903 and instability of theγ phase of alloy 909, two new alloys with good stress-rupture ductility, high creep-rupture strength, high tensile strength at high temperature, and good controlled thermal expansion were developed. These property improvements were accomplished by the combination of optimizing the Fe-Co-Ni ratio of the matrix and stabilizing theγ phase with the addition of aluminum.     

Activity measurements of Al and Cu in Si–Al–Cu melt at 1273 and 1373 K by the equilibration with molten Pb

For the effective control of Al introduction to solidified Si during the solidification refining of Si with the Si–Al-based melt for the solar cell material or the LPE Si film growth processes from the Si–Cu–Al solvent, thermodynamic properties of the Si–Al–Cu melt were investigated at 1273 and 1373 K. Activities of Al and Cu in the Si–Al–Cu melt were measured by the equilibration with molten Pb. Also, the excess Gibbs energy of the melt was studied by the ternary regular solution model.

The evaluated thermodynamic properties of the Si–Al–Cu melt indicated that Cu addition to the Si–Al melt brings the smaller activity coefficient of Al and is effective for reducing the Al content of solidified Si from the melt more effectively than its dilution effect for Al.     

Unitary equivalent classes of one-dimensional quantum walks

This study investigates unitary equivalent classes of one-dimensional quantum walks. We prove that one-dimensional quantum walks are unitary equivalent to quantum walks of Ambainis type and that translation-invariant one-dimensional quantum walks are Szegedy walks. We also present a necessary and sufficient condition for a one-dimensional quantum walk to be a Szegedy walk.     

Repeatedly foldable AMOLED display

In this study, a 5.9‐inch foldable active‐matrix organic light emitting diode (AMOLED) display was developed. A folding test was performed repeatedly. The display survived the folding test (100,000 folds) with a curvature radius of 2 mm. To protect an organic light emitting diode (OLED) against moisture, inorganic passivation layers are provided on the upper and lower sides of the flexible display. Using our transfer technology, high density passivation layers can be obtained. The measured water vapor transmission rate of the layer is 7 × 10^?6 g/m²?day or less, which improves OLED reliability. With these techniques, we have developed a book‐type display, which is repeatedly foldable like a book, and a tri‐fold display including a display area, which is foldable in three.     

500-fps face tracking system

In this paper, we propose a high-speed vision system that can be applied to real-time face tracking at 500 fps using GPU acceleration of a boosting-based face tracking algorithm. By assuming a small image displacement between frames, which is a property of high-frame rate vision, we develop an improved boosting-based face tracking algorithm for fast face tracking by enhancing the Viola–Jones face detector. In the improved algorithm, face detection can be efficiently accelerated by reducing the number of window searches for Haar-like features, and the tracked face pattern can be localized pixel-wise even when the window is sparsely scanned for a larger face pattern by introducing skin color extraction in the boosting-based face detector. The improved boosting-based face tracking algorithm is implemented on a GPU-based high-speed vision platform, and face tracking can be executed in real time at 500 fps for an 8-bit color image of 512 × 512 pixels. In order to verify the effectiveness of the developed face tracking system, we install it on a two-axis mechanical active vision system and perform several experiments for tracking face patterns.