Enhancing Chaotic Communication Performances by Manchester Coding

A numerical analysis of an optical chaotic transmission system, based on the synchronization of two chaotic lasers, in a master-slave closed loop configuration is presented. At the transmitter, the master chaotic wave is superposed on the information message; at the receiver, the message is recovered by subtracting the synchronized slave chaotic wave from the received signal. The performances are analyzed in terms of the Q-factor, considering two different message modulation formats: the nonreturn-to-zero and the Manchester coding. The Manchester coding shows enhanced performances due to the shift of the signal spectrum to higher frequencies.     

Effect of hot pressing on processing and properties of BBN ceramics

BBN (BaBi₂Nb₂O₉) is very interesting and promising lead free material with relaxor properties in capacitors, sensors and actuators.     

Mechanisms of rectification of a high-frequency signal by a field-effect heterotransistor with a short channel

The effect of nonlinearity of the drift velocity of free charge carriers and the gradient-and concentration-related nonlinearities in the power-voltage sensitivity of a field-effect transistor with a short channel are studied theoretically. Theoretical results are compared with experimental data on the detection of terahertz radiation. It follows from the comparison that, in order to gain deeper insight into observed systematic features in the analysis of high-frequency characteristics of the transistor, one has to take into account some other mechanisms of the current nonlinearity, in addition to the plasma-related nonlinearity.     

Investigation into Polarization of Unloaded and Loaded Microstrip Square-Ring Antennas

The polarization characteristic of unloaded and loaded square-ring microstrip antennas is investigated. Several different loading types like single-stub, dual-stub, notch, gap and shorting-pin are considered and their effects are studied. Loading enables feeding using a 50-Omega probe. The simulation and measurement results show that the loading techniques excite a loaded TMy ₁₁ mode that is orthogonal to the unloaded TMx ₁₁ mode. This indicates that by loading the ring antenna its polarization can be switched adaptively. However, the purity of the loaded and unloaded modes depends on the loading type. For some loading types like gap and shorting-pin, the excitation of the unloaded mode seems negligible, in comparison to the loadings by stub and notch. For the stub and notch loaded antennas the unloaded mode is also present, and its excitation efficiency is frequency dependent. Thus, their polarization plane, which is due to both loaded TMy ₁₁ and unloaded TMx ₁₁ modes, also becomes frequency dependant. The results of this investigation can be useful in selecting the loading methods for high-impedance microstrip ring antennas, and control of their impedance and polarization. The knowledge of the antenna polarization is essential in communications, and its dependence on the loading type can be used as an important parameter in design of adaptive antennas and sensors.     

Elimination of organic matter present in wastewaters from the cork industry by membrane filtration

BACKGROUND: The first stage of the cork industrial process generates great volumes of wastewater with moderate to high organic pollutant content that must be purified using different procedures, such as filtration by membranes. RESULTS: The tangential filtration of these wastewaters was studied using two different laboratory equipments. In the first one, three ultrafiltration (UF) membranes were tested, with molecular weight cut‐off (MWCO) 100 kDa and 30 kDa, and two operating modes were used: total recycling of permeate and retentate streams, and in continuous mode, without recycling both streams. In the total recycling UF experiments, the influence of the operating variables on the permeate flux was first established. The effectiveness of the different membranes was determined by evaluating the rejection coefficients for several parameters that measure the global pollutant content of the effluent. The values found for these rejection coefficients were in the following order: ellagic acid and color > absorbance at 254 nm > tannic content > COD (chemical oxygen demand). In the continuous mode experiments, the fouling mechanism for each membrane was established by fitting the experimental data to various filtration fouling models given in the literature. The operating mode in the second equipment was batch concentration, and additional experiments were carried out with an UF membrane (2 kDa), and with a NF membrane (with MWCO in the range 150–300 Da). CONCLUSIONS: The three operating modes tested provided different rejection levels of organic matter; among them, the most effective procedure tested was batch concentration mode using a NF membrane. Copyright © 2007 Society of Chemical Industry     

Complex processing of fluorine-containing wastes of fluorite ores

The possibility of processing fluorine-containing wastes of fluorite ore, which include fluorite, calcite, quartz, and anorthite, has been investigated. A manufacturing flow chart of the complex processing of the ore waste materials with the production of sodium fluoride, alumina, soda ash, and raw materials suitable for the production of Portland cement and wollastonite is suggested.     

Removal of impurities from liquid solutions by vacuum desorption with solvent evaporation

Mass transfer with solvent evaporation in the vapor-liquid two-phase film evaporators used for the removal of undesirable impurities from liquid solutions at low pressure is studied. The average concentrations of solution components in the falling liquid film are determined. The most efficient operating conditions for impurity removal, in which the resistance to mass transfer is concentrated in the liquid phase, are found. Original Russian Text ? V.N. Babak, T.B. Babak, L.P. Kholpanov, 2008, published in Teoreticheskie Osnovy Khimicheskoi Tekhnologii, 2008, Vol. 42, No. 6, pp. 654–670.     

Integrated carbon nanotube field emission differential amplifier: Modeling and measurement of the common-mode rejection ratio

A novel integrated vacuum field emission (VFE) differential amplifier (diff-amp) utilizing carbon nanotube (CNT) emitters has been developed. A dual-mask microfabrication process was employed to achieve a VFE diff-amp by integrating identical CNT VFE transistors with built-in split gates and integrated anodes. The identical pair of triode amplifiers was well-matched in their device characteristics. The measured ac small-signal characteristics of the diff-amp showed a common-mode-rejection ratio (CMRR) of ~ 320 (~ 50 dB). The proposed analytical model of the CMRR was verified to be in good agreement with the experimental data. The successful implementation of the CNT diff-amp demonstrates a new way to achieve temperature and radiation tolerant VFE integrated microelectronics.     

Sprinklered office fire tests

This paper presents data relating to the performance of sprinklers and detectors in real office fire situations. For sprinklers, these data are additional to that associated with the standardized testing used to determine the design delivery density and pressure requirements for various occupancy situations, and provide a useful insight into the effect of sprinklers on developing fires with various office situations. The data given in this paper include the times for activation of various types of sprinkler heads (normal and fast response), the efficacy of the systems as far as extinguishment is concerned, estimates of the maximum size of the fires prior to commencement of extinguishment and associated air temperatures at various locations within the office enclosures. Copyright © 2008 John Wiley & Sons, Ltd.     

Use of sequential x-ray fluorescence analysis for solving analytical problems in the glass industry

The capabilities of x-ray spectral instruments for fast analysis of raw materials and glass and ceramics were demonstrated. The range of the content of determinable elements in a sample ranges from 1 ppm to 100%. The measurement time is 10–15 sec.