Effect of poly(vinyl acetate/vinyl alcohol) copolymer with a thiol end group as a steric stabilizer on dispersion polymerization of styrene

In dispersion polymerization of styrene in ethanol, effects of a reactive steric stabilizer, poly(vinyl acetate/vinyl alcohol) copolymer with a thiol end group (P(VAc/VA)-SH), were investigated. In the absence of the thiol end group, the dispersion coagulated at the middle stage of the polymerization, while in the presence of the thiol end group, the polymerization proceeded successfully to result in close to monodisperse particles. The reactive thiol group acts as a site of formation of the block copolymer, that is, polystyrene-b-P(VAc/VA), which is utilized as an effective dispersant. From the measurement on molecular weights during the course of polymerization, two polymerization loci were realized. Addition of butyl methacrylate to styrene affected markedly not only rate of polymerization but also particle size. © 1996 John Wiley & Sons, Inc.     

Preparation and characterization of Mg–Al layered double hydroxides intercalated with benzenesulfonate and benzenedisulfonate

Mg–Al layered double hydroxides (Mg–Al LDHs) intercalated with benzenesulfonate (BS^–) and benzenedisulfonate (BDS^2–) ions were prepared by coprecipitation and characterized by X-ray diffraction, FT-IR spectroscopy, and chemical analyses. The intercalated BS^– and BDS^2– maintained their intrinsic molecular structures within the Mg–Al LDH interlayers. At low intercalation levels, the benzene ring of BS^– in BS · Mg–Al LDH was inclined at 30° relative to the plane of the brucite-like layers of Mg–Al LDH. With increasing BS^– content, the benzene ring adopted an additional configuration perpendicular to the Mg–Al LDH layers. In BDS-intercalated Mg–Al LDH, the benzene ring of BDS^2– was tilted at 26° relative to the plane of the Mg–Al LDH layers. Intercalation levels of BDS^2– were smaller than those of BS^– despite the greater charge density of BDS^2–, which was likely attributable to a greater degree of electrostatic repulsion between intercalated anions.     

Conceptual design of rain radar for the tropical rainfall measuring mission

Specifications for a spaceborne rain radar for tropical rainfall measurement are described. A spaceborne rain radar has problems peculiar to rain observation from space. The radar must have a fast scanning mechanism to cover a large swath. Very weak rain echoes compared to the sea or land surface signal must be detected. These capabilities must be attained under the severe power consumption and mass limitations of the satellite bus. The fast scanning requirement forces application of an electrically scanning mechanism. This requirement also causes a severe limitation of the available number of independent samples. The requirement for weak rain echoes excludes application of the pulse compression technique, which is a very conventional technique for other active microwave sensors on board satellites. Under these constraints, a rain radar with an electrically scanning planar antenna at 13-8 GHz is proposed.     

Development of a moderating type higher sensitive rem counter using 6Li glass scintillator

A moderating type higher sensitive neutron rem counter was constructed using grains of ⁶Li glass scintillator. The sensitivity of this counter is about 3.9 cps/(μSv/h), which is approximately 10 times higher than that of the commonly used rem counters and could be successfully applied for neutron monitoring both in the reactor room and the natural environment aided by the pulse-shape discrimination method.     

Carbonization of coals into anisotropic cokes: 7. Copreheat-treatment under short contact-time conditions at high temperature

The copreheat-treatment of non-fusible and slightly fusible coals with A240 and hydrogenated A240 under high temperature-short contact-time conditions around 500 °C has been examined in an attempt to produce a formed coke with better anisotropic development. These conditions shortened the copreheat-treatment time and provided better anisotropic development in the resultant coke after carbonization. Effectiveness of short contact-time has been discussed in terms of the extent of depolymerization of coal molecules suitable for anisotropic development, this being related to coal liquefaction under similar conditions.     

Enhancement of turbulent jet diffusion flame blowout limits by annular counterflow

The effects of a proposed combustion technique, named as annular counterflow, on the enhancement of jet diffusion flame blowout limits were investigated by a series of experiments conducted for the present study. Annular counterflow was formed in a concentric annulus, in which fuel jet was ejected from a nozzle and air was sucked into an outer cylinder encompassing the nozzle. Three fuel nozzles and outer cylinders of different sizes were utilized to perform the experiments. Schlieren technique and normal video filming were employed for the visualization of diverse flame morphologies triggered by the said flow. Gas samplings were taken and scrutinized by the use of a gas chromatograph. Results showed that the blowout limits can be enhanced dramatically by an increase in volume flow rates of air‐suction. Mixing enhancement is achieved with frequent and strong outward ejection of fluids from the cold jet when this technique is applied. The blowout limits are further extended when the diameter of outer cylinders becomes smaller and/or that of the fuel nozzle becomes larger. The base widths of lifted flames were found to be narrower in the interim of annular counterflow application. The rates of increase in flame lift‐off heights and base widths along with an increase in fuel flow velocities become sluggish when the volume flow rates of air are increased. The amount of fuel that was sucked into the outer cylinder was found to be negligible and trivial. A model based on annular and coaxial jet was developed to predict the lifted flame base width and blowout limits. The coincidence between the prediction and experimental results unambiguously validates that the momentum of air‐suction dominates the beneficial effect. Copyright © 2001 John Wiley & Sons, Ltd.     

A Computational Study of Thrust Vectoring Control Using Dual Throat Nozzle

Dual throat nozzle （DTN） is fast becoming a popular technique for thrust vectoring. The DTN is designed with two throats, an upstream minimum and a downstream minimum at the nozzle exit, with a cavity in between the upstream throat and exit. In the present study, a computational work has been carried out to analyze the performance of a dual throat nozzle at various mass flow rates of secondary flow and nozzle pressure ratios （NPR）. Two-dimensional, steady, compressible Navier-Stokes equations were solved using a fully implicit finite volume scheme. The present computational results were validated with available experimental data. Based on the present results, the control effectiveness of thrust-vectoring is discussed in terms of the thrust coefficient and the coefficient of discharge.     

A design of high optical efficiency wedge type light guide plate adopting twin inclined cylindrical surface

We propose wedge type light guide plate (LGP) adopting twin inclined cylindrical surfaces (TICS) at the incident part of a LGP. It has higher optical efficiency than conventional wedge type LGP. In dimension of LGP which the thickness of incident part is 1.5 mm and that of luminance part is 0.7 mm, the optical efficiency of wedge type LGP adopting TICS is expected to be 96% in comparison with a normal flat LGP. In addition, there is an advantage to reduce the non‐uniformity of vicinity of light emitted diodes (LEDs) by TICS reflecting light laterally. However, it is necessary that the LED centers are aligned with the intersections of TICS. The misalignment of LED causes non‐uniformity of optical profile that is slightly larger than a normal LGP.     

Thickness estimation of interface films formed on Li1−xCoO2 electrodes by hard X-ray photoelectron spectroscopy

Solid electrolyte interface (SEI) films formed on Li_1−xCoO₂ electrodes were observed with hard X-ray photoelectron spectroscopy (HX-PES). This paper particularly focuses on film thickness estimation using HX-PES with theoretical calculation. The validity of the calculation was proven by experiments using model SEI films. The native film formed on a LiCoO₂ composite electrode was estimated to be LiF with its thickness of 5 nm. Formation of Co (II) species on top of LiCoO₂ was also indicated. Storage of the electrode at 60 °C brought about considerable film growth (30-40 nm) with carbonate compounds formation. SEI film changes during charging of the LiCoO₂ electrode were also examined. The main component in the film was deduced to be LiF or a kind of fluorite, with its thickness decreased during charging. The SEI formation mechanisms are also elucidated.     

Passive Control of an Impulsive Wave Using a Cavity／Helical Vane System

INTRODUCTIONUnsteadycompressiblegasflowthroughaductisoftenencoullteredinmanyengineeringapplicationsandhasbeeninvestigatedbymanyresearchers.Whenapressurewavegeneratedinsideaductisdischargedfromanopenendoftheduct.animpulsivewave,whichcanbefrequentlycha...