Finite element analysis of wave motion

To estimate wave motion, the finite element method is presented based on the linear interpolation function and two-step explicit numerical integration in time. For the determination of free surface position, the two-step scheme based on the Eulerian technique is usefully employed. Travel and run-up of solitary wave have been analysed and compared with the analytical solution. Both results are reasonably well in agreement. This method is applied to estimate the wave force on the practical breakwater to show the validity of the method.     

Microanalyses on the RuO2 Particle–Glass Matrix Interface in Thick-Film Resistors with Piezoresistive Effects

The piezoresistive mechanisms of composite thick films based on RuO₂ particles and both calcium-borosilicate and bismuth-borosilicate glass matrices were investigated by chemical and electrical microanalyses. The resistor based on bismuth-borosilicate glass showed higher sensitivity than that based on calcium-borosilicate glass. It was confirmed that the diffusion of ruthenium into glass affects the binding state of RuO₂ at the interface of the glass. Furthermore, an intermediate resistive layer is detected around the RuO₂ particle. These results suggest that the piezoresistive effect is related to a change in the electrical conductivity of the interfacial reaction layer caused by the diffusion of ruthenium into glass.     

Maximum‐power‐point tracking method of photovoltaic power system using a single transducer

This paper describes a novel strategy of maximum‐power‐point tracking for photovoltaic power generation systems. A unique feature of this method is the capacity to see the maximum power point using only a single transducer, that is, a Hall‐effect CT or an isolation amplifier. Output power of the photovoltaic can be estimated with an average value and ripple amplitude of the detected reactor current or the capacitor voltage. A conventional hill‐climbing method is employed to seek the maximum power point, using the output power estimated with only the current or voltage transducer. In this paper, not only a theoretical aspect of the proposed method is discussed, but also experimental results are presented to prove the feasibility of the method. © 2007 Wiley Periodicals, Inc. Electr Eng Jpn, 160(1): 79– 86, 2007; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.20275     

Signal control by successive updating of control parameters based on prediction of traffic flow

In traditional coordinated traffic signal control on an urban road network, the following two problems occur. First, the conventional method involves a time lag between traffic measurement and signal control. Second, an abrupt switching of control parameters throws the traffic flow into disorder. This paper proposes a new approach to avoid these problems. We increase the frequency of switching. The control parameters are switched as frequently as every two cycles. At the time of switching, minor variations of the ongoing plan are generated. For each variation of plan, traffic delay at each intersection is predicted based on measured traffic data at upstream detectors. Then the plan minimizing the delay is chosen to be the control parameters in the next cycle. In order to evaluate the validity of this approach, experiments were carried out using a traffic simulator. The experiments indicate that the proposed method reduces the queue length significantly, compared with the conventional method. © 2007 Wiley Periodicals, Inc. Electr Eng Jpn, 161(3): 49–57, 2007; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.20391     

Difference in the detection limits of flaws in the depths of multi-layered and continuous aluminum plates using low-frequency eddy current testing

We examined the difference in the detection limits of flaws in the depths of multi-layered and continuous aluminum plates using low-frequency eddy current testing. The detection limits were measured by using a magneto-resistive sensor. Comparing the frequency of an applied magnetic field, the detection limit at 50 Hz is deeper than that at 1 kHz. Comparing the sample structure, the detection limit in the multi-layered samples is deeper than that in the continuous samples. These results are likely due to the differences in the skin depth and conductivity of the sample.     

Hydrogen isotope permeation from cooling water through various metal piping

In order to investigate the behavior of hydrogen isotope on the water–metal boundary, deuterium permeation experiments from heavy water vessel through various metal piping, such as pure iron (Fe), nickel (Ni), stainless steel (SS304), and pure iron with 10 μm gold plating, were performed at 573 K and at 15 MPa. During the experiment, surfaces of metal piping except gold plating one were oxidized at the heavy water boundary and then deuterium would generate by the oxidation reactions. This deuterium could be detected by mass spectrometer, which monitored the inside gases of the piping under continuous evacuation. The result showed clearly that the deuterium permeated through Fe, Ni, and SS304 piping was detected as mainly deuterium gas (D₂) under continuous evacuation, though that through gold plating one could not be detected effectively. The D₂ permeation rate through Fe, Ni, and SS304 piping reached equilibrium conditions with oxide generation at D₂O–metal boundary, although concluding the transfer mechanism will require further testing and modeling activities.     

Integrated circuits for television receivers

Integrated circuits are being investigated for use in as many television circuits as feasible. In Japan, considerable work has been done by different groups within the TV industry to develop ICs that will permit cost reduction, increased reliability, and simplification of assembly-line operations. This article is a report on results of the concentrated efforts made by five major television set manufacturers to develop and produce black-and-white and color receivers, in collaboration with four universities, two institutes, and seven components manufacturers.     

Japanese contribution to the DEMO-R&D program under the Broader Approach activities

Several technical R&D activities mainly related to the blanket materials are newly launched as a part of the Broader Approach (BA) activities, which was initiated by the EU and Japan. According to the common interests for these parties in DEMO, R&Ds on reduced activation ferritic/martensitic (RAFM) steels as structural material, SiC_f/SiC composites as a flow channel insert material and/or alternative structural material, advanced tritium breeders and neutron multipliers, and tritium technology are carried out through the BA DEMO R&D program, in order to establish the technical bases on the blanket materials and the tritium technology required for DEMO design. This paper describes overall schedule of those R&D activities and recent progress in Japan carried out by JAEA as the domestic implementing agency on BA, collaborating with Japanese universities and other research institutes.     

E.s.r. studies on free radicals generated in poly[p-(2-hydroxyethoxy) benzoic acid] fibres at low temperatures

Free radicals generated in stretched and ground poly [p-(2-hydroxyethoxy) benzoic acid] (PEOB) were studied by e.s.r. spectroscopy in an effort to isolate those formed by main chain scission. PEOB fibres stretched at ?86°C in a dry nitrogen atmosphere gave an asymmetric spectrum, which had patterns characteristic of both phenoxy and peroxy radicals in addition to some unknown peaks. The shape of the spectrum changed with increasing temperatures, finally becoming identical to that of phenoxy radicals at room temperature. The phenoxy radical was observed in all PEOB films ground or γ-irradiated in liquid nitrogen. In some cases a small peak of peroxy radical was observed. Theoretical spectra calculated for possible radical species or combinations of them were compared with those observed. No direct evidence was observed of the formation of alkyl type and radicals which were assumed to be formed with phenoxy radicals upon main chain rupture of PEOB. However, the relatively unstable peroxy radical observed in these experiments is thought to arise from them.