Low-Power VLSI Implementation of the Inner Receiver for OFDM-Based WLAN Systems

In this paper, we propose low-power designs for the synchronizer and channel estimator units of the Inner Receiver in wireless local area network systems. The objective of the work is the optimization, with respect to power, area, and latency, of both the signal processing algorithms themselves and their implementation. Novel circuit design strategies have been employed to realize optimal hardware and power efficient architectures for the fast Fourier transform, arc tangent computation unit, numerically controlled oscillator, and the decimation filters. The use of multiple clock domains and clock gating reduces the power consumption further. These blocks have been integrated into an experimental digital baseband processor for the IEEE 802.11a standard implemented in the 0.25mum- 5-metal layer BiCMOS technology from Institute for High Performance Microelectronics.     

Study of a BGO calorimeter using electron and hadron beams from 1 to 50 GeV

A calorimeter of 25 bismuth germanate (BGO) crystals equipped with silicon photodiode readout has been tested at the CERN SPS in the energy range 1–50 GeV. The response for electrons has been shown to be linear in this energy range and the rms resolution obtained ( ) is approximately 1%, for E > 4 GeV. The electron/pion separation was found to be better than 1:500 in the energy range 1–20 GeV. Data on lateral and longitudinal shower development were compared with the results of a Monte Carlo simulation using the SLAC-EGS program and found to be in good agreement.     

Fuel modelling in fast reactor whole core accident calculations

Transient fuel pin behaviour and fuel motion models are of major importance for the analysis of the initiation phase of unprotected whole-core LOF and TOP accidents in LMFBRs. The role played by these models is highlighted by discussing LOF and TOP accident sequences. This is followed by an overview of present whole-core fuel pin behaviour and fuel motion models and also a critical evaluation of these models.     

Synthesis and characterization of morphologically different high purity gallium oxide nanopowders

High purity gallium oxide nanopowders have been synthesized by using a simple precipitation technique with calcination at elevated temperature. From the X-ray pattern, the phase purity of the synthesized powders was confirmed as β-Ga₂O_3. Elemental quantification (stoichiometry) of Ga₂O₃ was also examined from the X-ray energy dispersive analysis (EDAX). Based on the recorded Fourier Transform Infrared (FTIR) spectrum of Ga₂O_3, the IR bands due to Ga–O bond and crystal lattice vibrations have been identified in the wavenumber range 400–4,000 cm⁻¹. From the measured SEM images, it is obvious to notice that the pH value has been playing a dominant role in obtaining morphologically different gallium oxide nanopowders. Thermogravimetric analysis reveals 8.3% of weight loss when the sample was heated to the temperature of 1,100 °C from the room temperature, which also shows a crystalline phase transformation. It is very interesting to report that a broad blue emission at 455 nm has been measured from the synthesized gallium oxide nanopowders.     

Phase relations in the ternary system Cu-In-Se

The phase relations of the ternary system Cu-In-Se were studied at 750° C by quenching experiments. Special attention was given to the region CuInSe₂In₂Se₃-In₄Se₃. Only four ternary phases with extended homogeneity ranges were found to exist. They were characterized by X-ray powder diffraction, electron microprobe analysis (EK8PA)' end optical microscopy. Differential thermal analysis (DTA) investigations allowed us to construct theT-x diagram of the Cu₂Se-In₂Se₃. out between 47 and 100 mol% In₂Se₃. Besides, it was also possible to give a tentative diagram of the solid-liquid equilibria at 750° C and to get some information on the sub-solid existence fields beside the Cu₂Se-In₂Se₃ cut.     

An integrated system to remote monitor and control anaerobic wastewater treatment plants through the internet.

The TELEMAC project brings new methodologies from the Information and Science Technologies field to the world of water treatment. TELEMAC offers an advanced remote management system which adapts to most of the anaerobic wastewater treatment plants that do not benefit from a local expert in wastewater treatment. The TELEMAC system takes advantage of new sensors to better monitor the process dynamics and to run automatic controllers that stabilise the treatment plant, meet the depollution requirements and provide a biogas quality suitable for cogeneration. If the automatic system detects a failure which cannot be solved automatically or locally by a technician, then an expert from the TELEMAC Control Centre is contacted via the internet and manages the problem.     

Effect of ionic content,solid content,degree of neutralization,and chain extension on aqueous polyurethane dispersions prepared by prepolymer method

There are many variables in the preparation of aqueous polyurethane (PU) dispersions. Carboxylic acid content, solid content, degree of pre/postneutralization of the carboxylic acids, and chain extension all impact dispersion particle size, viscosity, pH, molecular weights, and glass transition temperature. This study evaluated the impact of these variables on a given PU dispersion formulation prepared from isophorone diisocyanate, an aliphatic polyester polyol, dimethylol propionic acid, and hexamethylene diamine with triethyl amine as the neutralizing base and N‐methyl pyrrolidone as the cosolvent. Changes in carboxylic acid content, degree of preneutralization, and chain extension were found to have the expected impacts on dispersions properties. Increased ionic content in the dispersion step led to lower particle size and higher viscosity, increased chain extension with its concurrent increase in molecular improved subsequent film properties. Surprising results were obtained by varying the amount of postneutralization and from increased solids content at the time of dispersion. Unexpectedly, both of these variations led to much higher dispersion viscosities and particle size in solution. To have these changes take place, it is theorized that there is a major change in solution morphology caused by these modifications. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 98: 2514–2520, 2005