Optimization of modulation bandwidth in DBR lasers with detunedBragg reflectors

The dynamical behavior of distributed Bragg reflector lasers with detuned Bragg reflectors is investigated theoretically. The model is based on the traveling wave equations, which are solved by expanding the solution in terms of the longitudinal eigenmodes. It is shown that for a drastic enhancement of the modulation bandwidth the interplay of the dominant mode and one side mode has to be enforced. Under these conditions, the modulation bandwidth can be enhanced to more than 70 GHz     

Low temperature wafer direct bonding

A pronounced increase of interface energy of room temperature bonded hydrophilic Si/Si, Si/SiO₂, and SiO₂/SiO ₂ wafers after storage in air at room temperature, 150°C for 10-400 h has been observed. The increased number of OH groups due to a reaction between water and the strained oxide and/or silicon at the interface at temperatures below 110°C and the formation of stronger siloxane bonds above 110°C appear to be the main mechanisms responsible for the increase in the interface energy. After prolonged storage, interface bubbles are detectable by an infrared camera at the Si/Si bonding seam. Desorbed hydrocarbons as well as hydrogen generated by a reaction of water with silicon appear to be the major contents in the bubbles. Design guidelines for low temperature wafer direct bonding technology are proposed     

A linkage map of human chromosome 21:43 PCR markers at average intervals of 2.5 cM

A genetic linkage map of human chromosome 21q (HC21q) containing 43 markers genotyped by the polymerase chain reaction in the CEPH pedigrees is presented. The markers placed on this map are highly polymorphic with an average heterozygosity of 61%. The average interval size of the markers localized at 1000:1 odds is 2.5 cM. The map has a total length of 65.5 cM, with male and female lengths of 47.7 and 83.3 cM, respectively. The genotypes used in the construction of this map were subjected to rigorous error checking, which is reflected in the shorter map length compared to previous maps; the estimated error rate in genotyping is less than 0.04%. As noted in previous linkage maps there is increased recombination in females on proximal HC 21q and in the male in a region near the telomere. This map of HC 21 represents a highly informative and dense meiotic linkage map and will be useful in linking disease phenotypes to loci on this chromosome.     

DQ-haplotype analysis in rhesus macaques: implications for the evolution of these genes

The DQA1 and DQB1 alleles of 258 rhesus monkeys (Macaca mulatta) of different origin were typed by PCR-RFLP. Five novel MamuDQA1 and five novel -DQB1 alleles were detected and 15 Mamu-DQA1-DQB1 haplotypes were identified. Haplotype analysis confirmed the conservation of the DQA1*01-DQB1 *06 haplotypes in evolution. The most conspicuous finding was the tight linkage between the Mamu-DQA1 and -DQB1 alleles. Almost in every case the Mamu-DQA1 allele was linked to only one particular Mamu-DQB1 allele. Although there also are constraints in the formation of DQ haplotypes in humans, such tight linkages are not observed. These findings support the hypothesis of some kind of co-evolution between DQA1 and DQB1 alleles and may reflect a stronger force of natural selection in macaques than in humans.     

Active,passive and transpassive dissolution of a nickel base super alloy in concentrated acid mixture solution

The electrochemical and corrosion behaviour of a nickel base super alloy (C-263) has been investigated in the deaerated binary and ternary solution mixture of concentrated phosphoric acid, acetic acid, sulphuric acid, nitric acid or water using potentiostatic technique at 35°C. The possibilities of electropolishing of this alloy in these solution mixtures have been also explored. The alloy showed distinct active, passive and transpassive behaviour in the experimental solutions. The alloy remained active and turned passive in the negative potential region. Transpassive dissolution of the alloy is observed and electropolishing is achieved in this region. The best electropolishing is obtained in 50% H₃PO₄ + 40% CH₃COOH + 10% H₂SO₄. Higher content of water in the electrolytic solution is not useful for electropolishing of the alloy The experimental results also suggest that a current plateau in the transpassive potential region is not a sufficient condition to achieve electropolishing.     

Functional Properties and Food Applications of Rapeseed Protein Concentrate

Rapeseed protein concentrate (RC), prepared with 2% hexameta-phosphate, was tested for its functionality and performance in some foods. The RC had good nitrogen solubility, fat absorption, emulsification, and whipping capacities but poor water absorption and gelling properties. It increased the emulsion stability, and protein but lowered the fat content of wieners. It also increased the cooking yield, reduced the shrinkage and tenderized meat patties. Results were similar to soybean isolate except for the poorer color and flavor. The cooking yield of RC supplemented wieners was less than the all-meat control and soybean-supplemented wieners. A 9% RC dispersion mixed with an equal volume of eggwhite produced a meringue of comparable stability and texture to that of eggwhite alone.     

Systematic characterization of Cl2 reactive ion etchingfor improved ohmics in AlGaN/GaN HEMTs

Pre-metal-deposition reactive ion etching (RIE) was performed on an Al_0.3Ga_0.7N/AlN/GaN heterostructure in order to improve the metal-to-semiconductor contact resistance. An optimum AlGaN thickness for minimizing contact resistance was determined. An initial decrease in contact resistance with etching time was explained in terms of removal of an oxide surface layer and/or by an increase in tunnelling current with the decrease of the AlGaN thickness. The presence of a dissimilar surface layer was confirmed by an initial nonuniform etch depth rate. An increase in contact resistance for deeper etches was experienced. The increase was related to depletion of the two-dimensional (2-D) electron gas (2-DEG) under the ohmics. Etch depths were measured by atomic force microscopy (AFM). The contact resistance decreased from about 0.45 Ωmm for unetched ohmics to a minimum of 0.27 Ωmm for 70 Å etched ohmics. The initial thickness of the AlGaN layer was 250 Å. The decrease in contact resistance, without excessive complications on device processing, supports RIE etching as a viable solution to improve ohmic contact resistance in AlGaN/GaN HEMTs     

How Japan's Recently Amended Copyright Law Affects Software

Japan rejected a proposal to adopt a special software protection law and instead modified its copyright law to include software. This change may affect US firms doing business there.     

Low-Power VLSI Implementation of the Inner Receiver for OFDM-Based WLAN Systems

In this paper, we propose low-power designs for the synchronizer and channel estimator units of the Inner Receiver in wireless local area network systems. The objective of the work is the optimization, with respect to power, area, and latency, of both the signal processing algorithms themselves and their implementation. Novel circuit design strategies have been employed to realize optimal hardware and power efficient architectures for the fast Fourier transform, arc tangent computation unit, numerically controlled oscillator, and the decimation filters. The use of multiple clock domains and clock gating reduces the power consumption further. These blocks have been integrated into an experimental digital baseband processor for the IEEE 802.11a standard implemented in the 0.25mum- 5-metal layer BiCMOS technology from Institute for High Performance Microelectronics.