Primer-induced labeling of pea and field bean chromosomes in situ and in suspension

A protocol for primed in situ DNA labeling (PRINS) was optimized for pea (Pisum sativum L.) and field bean (Vicia faba L.) chromosomes attached to coverslips. Cloned DNA or synthetic oligonucleotides were used as probes for repetitive DNA sequences (rDNA, Fok-element) and different reaction conditions were tested to achieve the highest specific signal-to-background ratio. A procedure based on direct labeling by fluorescein-dUTP was compared with an indirect one using digoxigenin detected by fluorescently labeled antibody. Under optimal conditions, strong and specific signals were obtained exclusively on chromosome regions known to contain respective DNA sequences. Compared to the direct labeling, significantly stronger signals were obtained when the indirect procedure was used. Both types of labeling were successfully applied to chromosomes in suspension and were shown to produce signals comparable to that obtained with chromosomes attached to coverslips. It is expected that primed in situ DNA labeling en suspension (PRINSES) will provide a basis for flow-cytometric discrimination and sorting of otherwise indistinguishable chromosomes according to their specific fluorescent labeling.     

Mesa and planar SiGe-HBTs on MBE-wafers

SiGe-HBTs have the potential for outstanding analog and digital or mixed-signal high frequency circuits widely based on standard Si technology. Here we review on MBE grown transistors and circuits. Processes and results of a research-like SiGe HBT and two possible production relevant HBT versions are presented. The high frequency results with f_max and f_T up to 120 GHz and a minimum noise figure of 0.9 dB at 10 GHz demonstrate the advantage of using MBE samples with steep and high base doping and high germanium contents. A comparison to the concept of reported low doped, low germanium and triangular profiled SiGe base layers, realized by UHV-CVD, is given. In addition, some circuit demonstrators of SiGe-ICs will be presented.     

2 cm long monolithic multisection laser for active modelocking at 2.2 GHz

A 2 cm long three-contact multisection laser has been fabricated for modelocking at very low repetition rates. Active modelocking yields 8.0-12.3 ps pulses at 2.2, 4.3 and 6.5 GHz corresponding to the fundamental, first, and second harmonics of the cavity resonance frequency. This device demonstrates the feasibility of fabricating monolithic pulse sources operating at rates as low as the OC-48 Sonet transmission rate (2.488 Gbit/s).<>     

Adaptation of drafting plotter for buried contact groove formation

Lasers (e.g. Nd-YAG) have been used extensively for groove formation both in laboratories and commercial production but the initial capital cost is high. The production throughput is also low and thus adds to the cost of the cell. To reduce cost and increase production throughput a drafting plotter has been adapted to serve as a mechanical scriber for groove formation. The adapted plotter can scribe cells in matrix form to reduce the human labour and increase the production throughput. The characterization of the scribing tips in conjunction with the plotter showed that the best yield for the scriber is obtained when the scribing tip is mounted at 78° to the stock. Of the seven characterized scribing tips, the 90° conical scriber has been found to give the same groove geometry as the laser. The application of the adapted plotter to cell fabrication did not show any significant deterioration in the electrical output parameters for the mechanically scribed cells when compared with laser scribed cells. This article reports the adaptation of the x-y table drafting plotter to form buried contact grooves.     

Crystallographic shear planes in nanocrystalline SnO2 thin films by high-resolution transmission electron microscopy

Atomic structures of crystallographic shear planes (CSPs) in nanocrystalline thin films of semiconductor SnO₂ were investigated by high-resolution electron microscopy. The films were prepared by electron beam evaporation in high vacuum (10^–6 torr) and followed by annealing in synthetic air at 700 °C for 1–2 H. CSPs with the displacement vector of [1/2 0 1/2] were observed in the planes parallel to (¯101), (110) and (¯3¯21). Most of the CPSs were found to terminate or interact with each other within SnO₂ crystallites. Partial dislocations exist at terminal places of CSPs or along intersecting lines of CSPs. CSP steps were also observed. Structural models of these defects have been proposed. Based on analysis of experimental data, it has been suggested that the Sn/O ratio at CSPs which are not parallel to their displacement vector, at cores of partial dislocations and at CSP steps, is higher than that of the perfect structure, that is, these defects are able to provide extra free electrons with the films.     

Monitoring cancer antigen 125 in serum of ovarian cancer patients after administration of 131I-labeled F(ab')2 fragments of OC125 antibody

We evaluated the effect of repeated administration of OC125 F(ab')2 fragments on cancer antigen (CA) 125 determination in 210 serum samples from 30 patients. We found falsely high CA 125 concentrations in 142 (68%) samples, using a homologous CA 125 enzyme immunoassay (EIA) with OC125 antibodies. The Truquant OV2 method, which involves two other murine antibodies, and the IMx CA 125 method, which uses sheep antibodies as capture antibodies, resulted in only slightly increased (false-positive) values in some samples with exceptionally high CA 125 EIA values. We measured falsely low CA 125 values in 37 (18%) samples with the Truquant OV2 method. Interferences could be eliminated by removal of serum IgG. Our results suggest that interferences are to some extent caused by anti-idiotypic IgG induced by OC125 administration. Assays involving nonmurine anti-CA 125 antibodies as capture antibodies seem to be most suited for CA 125 determination after OC125 treatment, but in every case an apparent increase of CA 125 after OC125 infusion should be validated.