Enrichment procedures for trace metal analysis by atomic absorption spectrophotometry have been investigated. The detection
limits are primarily determined by the enrichment factor and the accuracies have been found to be roughly the same within
the same absorption ranges independent of the method used.
One of 28 papers presented at the Symposium, “Metal-Catalyzed Lipid Oxidation,” ISF-AOCS World Congress, Chicago, September
1970. 相似文献
Light up galectin: Photoprobes based on thiodigalactoside were prepared for galectin‐3, a lectin linked to cancer. The probes contained either benzophenone or acetophenone moieties as the photolabel for covalent attachment to the protein. One particular probe labeled galectin‐3 selectively, even in the presence of cell lysate.
Mathematical modelling has proven to be very useful in process design, operation and optimisation. A recent trend in WWTP modelling is to include the different subunits in so-called plant-wide models rather than focusing on parts of the entire process. One example of a typical plant-wide model is the coupling of an upstream activated sludge plant (including primary settler, and secondary clarifier) to an anaerobic digester for sludge digestion. One of the key challenges when coupling these processes has been the definition of an interface between the well accepted activated sludge model (ASM1) and anaerobic digestion model (ADM1). Current characterisation and interface models have key limitations, the most critical of which is the over-use of Xc (or lumped complex) variable as a main input to the ADM1. Over-use of Xc does not allow for variation of degradability, carbon oxidation state or nitrogen content. In addition, achieving a target influent pH through the proper definition of the ionic system can be difficult. In this paper, we define an interface and characterisation model that maps degradable components directly to carbohydrates, proteins and lipids (and their soluble analogues), as well as organic acids, rather than using Xc. While this interface has been designed for use with the Benchmark Simulation Model No. 2 (BSM2), it is widely applicable to ADM1 input characterisation in general. We have demonstrated the model both hypothetically (BSM2), and practically on a full-scale anaerobic digester treating sewage sludge. 相似文献
The distribution of different iron (Fe) species in soils, sediments, and surface waters has a large influence on the mobility and availability of Fe, other nutrients, and potentially toxic trace elements. However, the knowledge about the specific forms of Fe that occurs in these systems is limited, especially regarding associations of Fe with natural organic matter (NOM). In this study, extended X-ray absorption fine structure (EXAFS) spectroscopy was used to characterize Fe(III) in organic soils (pH 4.6-6.0) with varying natural Fe content. The EXAFS data were subjected to wavelet transform analysis, to facilitate the identification of the nature of backscattering atoms, and to conventional EXAFS data fitting. The collective results showed the existence of two pools of iron: mononuclear Fe(III)-NOM complexes and precipitated Fe(III) (hydr)oxides. In the soil with lowest pH (4.6) and Fe content mononuclear organic complexes were the completely dominating fraction whereas in soils with higher pH and Fe content increasing amounts of Fe (hydr)oxides were detected. These results are of environmental importance, as the different iron pools most likely have markedly different reactivities. 相似文献
This paper describes and validates by comparisons with tests a one‐zone model for computing temperature of fully developed compartment fires. Like other similar models, the model is based on an analysis of the energy and mass balance assuming combustion being limited by the availability of oxygen, ie, a ventilation‐controlled compartment fire. However, the mathematical solution techniques in this model have been altered. To this end, a maximum fire temperature has been defined depending on combustion efficiency and opening heights only. This temperature together with well‐defined fire compartment parameters was then used as a fictitious thermal boundary condition of the surrounding structure. The temperature of that structure could then be calculated with various numerical and analytical methods as a matter of choice, and the fire temperature could be identified as a weighted average between the maximum fire temperature and the calculated surface temperature of the surrounding structure as a function of time. It is demonstrated that the model can be used to predict fire temperatures in compartments with boundaries of semi‐infinitely thick structures as well as with boundaries of insulated and noninsulated steel sheets where the entire heat capacity of the surrounding structure is assumed to be concentrated to the steel core. With these assumptions, fire temperatures could be calculated with spreadsheet calculation methods. For more advanced problems, a general finite element solid temperature calculation code was used to calculate the temperature in the boundary structure. With this code, it is possible to analyze surrounding structures of various kinds, for example, structures comprising several materials with properties varying with temperature as well as voids. The validation experiments were accurately defined and surveyed. In all the tests, a propane diffusion burner was used as the only fire source. Temperatures were measured with thermocouples and plate thermometers at several positions. 相似文献