A novel way to treat refractory waste: Sonication followed by wet oxidation (SONIWO)

The effectiveness of the hybrid system sonication followed by wet oxidation (SONIWO) to treat otherwise refractory waste has been demonstrated. In such a hybrid system homogeneous CuSO₄ catalyst was found to be very efficient.     

Cold forging and chemical heat treatment of the casing of the internal joint for VAZ cars

The technological process of cold forging applied for the first time in the production of the casing of the internal joint with races is described. The process operations of cold forging and the annealing and carburizing regimes for this part me described.     

Monitoring systems and determination of actual fatigue usage

At GKN, fatigue monitoring of important components has been conducted since 1979. The monitoring methods depend on the mechanisms of damage; quasi-static loads are regarded as well as dynamic loads. The components were selected for monitoring on the basis of a system analysis. The data resulting from monitoring are used to optimise operation mode steadily. Experience shows that the use of monitoring data as input for fatigue assessment is the most realistic and cost-effective way. This fatigue assessment uses global and local sensitivity studies to evaluate the load-stress relation for each component. These relations can be programmed to produce stress vs. time curves. These are processed according to ASME rules to give a realistic fatigue usage.     

Increasing the interference immunity of broadband systems for measuring and transmitting information by utilizing nonlinear signal processing methods

A method is considered for increasing the immunity from interference of broadband systems for measuring and transmitting information. It is based on utilizing nonlinear methods to process spread-spectrum signals. The possibility is investigated of using a quasioptimal receiving device which can be implemented in practice. It is shown that the proposed method makes it possible to solve the rejection problem at the physical level. Translated from Izmeritel'naya Tekhnika, No. 11, pp. 13–15, November, 1996.     

Radon as a risk factor for extra-pulmonary tumours

Most divers and diving medicine specialists know that application of normobaric oxygen as first aid after a bubble disease incident is highly effective. However, as yet technical difficulties acted as a deterrent to using normobaric oxygen at the diving site. This can now be overcome by a newer technique. To be efficient, any therapy of bubble disease should follow three main principles: maximal partial pressure of inhaled oxygen (i.e. 100 kpa in normobaric, and 280 kpa in hyperbaric conditions); minimal partial pressure of inhaled nitrogen, which should ideally be near zero; immediate start of therapy, if possible at the diving site, but not later than 2 hours after the onset of the first symptoms. However, it has to be borne in mind that for an efficient normobaric oxygenation (100%), the standard apparatus design without oxygen reservoir is obsolete, for it offers at most 40% oxygen to the lungs. Currently the following technical approaches for an efficient normobaric oxygenation are available: open one-way systems with tightly fitting mask and oxygen reservoir bag (type Ambu or Leardal, etc.); open systems with on-demand regulation and tightly fitting mouth piece (type SCUBA, or Bird-respirator); closed systems with CO2 absorber (type oxygen rebreathing diving gear). The closed system is a genuine technical advance, because it needs 15 times less oxygen than open systems (about 90 liters oxygen for a 3-hours oxygenation run). Such an apparatus is thus of light weight, far less cumbersome, and nevertheless highly efficient. The therapy should start immediately at the site of the mishap and be maintained during the transport to the next HBO-unit (usually 3 to 6 hours).(ABSTRACT TRUNCATED AT 250 WORDS)     

Experience in High-Temperature Thermomechanical Treatment with Helical Reduction in the Production of Axisymmetric Parts

Metal Science and Heat Treatment -     

Functional Properties and Food Applications of Rapeseed Protein Concentrate

Rapeseed protein concentrate (RC), prepared with 2% hexameta-phosphate, was tested for its functionality and performance in some foods. The RC had good nitrogen solubility, fat absorption, emulsification, and whipping capacities but poor water absorption and gelling properties. It increased the emulsion stability, and protein but lowered the fat content of wieners. It also increased the cooking yield, reduced the shrinkage and tenderized meat patties. Results were similar to soybean isolate except for the poorer color and flavor. The cooking yield of RC supplemented wieners was less than the all-meat control and soybean-supplemented wieners. A 9% RC dispersion mixed with an equal volume of eggwhite produced a meringue of comparable stability and texture to that of eggwhite alone.     

Neutron-activation determination of elements with overlapping resonances in neutron-absorption cross sections

Translated from Atomnaya Énergiya, Vol. 66, No. 6, pp. 423–424, June, 1989.     

Use of166mHo for calibration of gamma-ray spectrometers with semiconductor detectors

Translated from Atomnaya Énergiya, Vol. 67, No. 3, pp. 215–216, September, 1989.