Development and adoption of measures for increasing the safety of power-generating units of nuclear power plants with RBMK reactors in 1986–2005

The basic stages and directions of upgrading and reconstruction of the power-generating units of nuclear power plants with RBMK reactors over a period of 20 yr since the Chernobyl accident are reflected in this paper. The greatest amount of work was done in 1986–1990 on all units with RBMK-1000 and-1500 reactors which were operating at that time in the USSR. The purpose of the upgrade was to improve the neutron-physical characteristics of the reactor cores, increase the response speed of the safety and control system and decrease the positive effect of water outflow from the cooling loop of this system, increase the flow capacity of the systems performing emergency discharge of the steam-gas mixture from the reactor, and improve the basic operating documentation. The subsequent stages of the upgrading and reconstruction concerned mainly the first-generation power-generating units (Nos. 1 and 2 units of the Leningrad and Kursk nuclear power plants). These works were performed to make the power-generating units conform to the requirements of the modern normative documents on safety and allow for the possibility of these units to remain in operation after the nominal 30-yr service life has been exhausted. __________ Translated from Atomnaya énergiya, Vol. 100, No. 4, pp. 312–320, April, 2006.     

Nitrification parameter measurement for plant design: experience and experimental issues with new methods.

Nitrification kinetics are important for process design, optimization, and capacity rating of activated sludge wastewater treatment plants. A Water Environment Research Foundation (WERF) project on Methods for Wastewater Characterization in Activated Sludge Modeling (WERF, 2003) focused significantly on the development of procedures for measuring the nitrifier maximum specific growth rate, micro(AUT). In addition, the importance of (and lack of data for) the nitrifier decay rate, b(AUT), was identified. This paper describes three bench-scale methods for measuring micro(AUT): the Low F/M SBR, Washout and High F/M methods. During the WERF project, the importance of pH and temperature control was investigated briefly; this paper summarizes further experimental work performed to address these issues. A summary of micro(AUT) measurements in a number of locations and using the different measurement techniques is provided.     

Degradation of wine industry wastewaters by photocatalytic advanced oxidation.

Wine industry wastewaters contain a high concentration of organic biodegradable compounds as well as a great amount of suspended solids. These waters are difficult to treat by conventional biological processes because they are seasonal and a great flow variation exists. Photocatalytic advanced oxidation is a promising technology for waters containing high amounts of organic matter. In this study we firstly investigated the application of H2O2 as oxidant combined with light (artificial or natural) in order to reduce the organic matter in samples from wine industry effluents. Secondly, we studied its combination with heterogeneous catalysts: titanium dioxide and clays containing iron minerals. The addition of photocatalysts to the system reduces the required H2O2 concentration. Although the H2O2/TiO2 system produces higher efficiencies, the H2O2/clays system requires a H2O2 dosage between three and six times lower.     

The Effect of Nucleators on the Quality of the Surface of Glass-Ceramic Denture Coatings

The effect of nucleator additives on the surface relief and the degree of crystallization of material intended for the dentine and enamel layers of artificial denture is considered. It is established that hydroxyapatite additive is optimal for producing the required relief in the prime and dentine layers.     

Final Drying of Whole Milk Powder in Vibrated-Fluidized Beds

Vibro-fluidized beds are widely used in drying sticky powders and agglomerated materials as milk powder. Using a vibro-fluidized laboratory scale dryer, this work is aiming at analyzing preliminarily the effect of its operational variables on the drying kinetics and characteristics of whole milk powder. The full-factorial design technique with three replications at the central point has been employed to generate data and correlations to quantify the effect of inlet air temperature, air flow rate, and vibration bed amplitude on the drying curves and the milk powder properties related to its faster reconstitution in water (as tapped density, Hausner cohesion ratio, agglomerate size distribution, and internal pore concentration). Results obtained are analyzed and discussed to identify the adequate operation condition for final drying whole milk powder in vibro-fluidized beds, assuring a high product quality.     

Analysis of supersaturation and nucleation in a moving solution droplet with flowing supercritical carbon dioxide

A supercritical antisolvent (SAS) process is employed for production of solid nanoparticles from atomized droplets of dilute solution in a flowing supercritical carbon dioxide (SC CO₂) stream by attaining extremely high, very rapid, and uniform supersaturation. This is facilitated by a two‐way mass transfer of CO₂ and solvent, to and from the droplet respectively, rendering rapid reduction in equilibrium solubility of the solid solute in the ternary solution. The present work analyses the degree of supersaturation and nucleation kinetics in a single droplet of cholesterol solution in acetone during its flight in a flowing SC CO₂ stream. Both temperature and composition are assumed to be uniform within the droplet, and their variations with time are calculated by balancing the heat and mass transfer fluxes to and from the droplet. The equilibrium solubility of cholesterol with CO₂ dissolution has been predicted as being directly proportional to the Partial Molar Volume Fraction (PMVF) of acetone in the binary (CO₂–acetone) system. The degree of supersaturation has been simulated up to the time required to attain almost zero cholesterol solubility in the droplet for evaluating the rate of nucleation and the size of the stable critical nuclei formed. The effects of process parameters have been analysed in the pressure range of 7.1–35.0 MPa, temperature range of 313–333 K, SC CO₂ flow rate of 0.1136–1.136 mol s^?1, the ratio of the volumetric flow rates of CO₂‐to‐solution in the range of 100–1000, and the initial mole fraction of cholesterol in acetone solution in the range of 0.0025–0.010. The results confirm an extremely high and rapid increase in degree of supersaturation, very high nucleation rates and stable critical nucleus diameter of the order of a nanometre. Copyright © 2005 Society of Chemical Industry     

Estimation of fouling in a plate heat exchanger through the application of neural networks

Pasteurization is an important, if not the most important, process step in the packaging of milk. It is subject to alterations stemming from the variation in the temperature, pH and raw milk quality. The variability may manifest itself in changes in the formation of the deposit (fouling) in the pasteurization unit, such that there is a need for tools, both instrumentation and computational, to help in monitoring the process and keeping it on the desired course. In this paper we describe a practical procedure based on artificial neural networks (ANN) that allows prediction of the deposit thickness, the overall heat transfer coefficient and the critical time (the time that the unit has to be stopped for cleaning) for reducing the impact of fouling on such processes. The procedure determines when the cleaning operation is required once the system is under critical conditions of operations. A combination of fundamental studies and plant measurements were used for study of the operating conditions and thus evaluation of the trades‐offs between operating conditions and longer operating life span. The results are encouraging, enough to validate current operating industrial techniques. Copyright © 2005 Society of Chemical Industry     

Intraoperative neurological monitoring

Intraoperative neurological monitoring (INM) is the evaluation of the nervous system within the operating room (OR) environment. In this paper, the INM system is tested in a clinical setting in comparison with conventional somatosensory evoked potential (SEP) monitoring. The study results demonstrate the capability of the INM system in extracting clearer and more stable SEP signals. The high SNR of SEP signals collected in various clinical environments, including the OR, makes the INM system a robust platform for continuous monitoring. While the current use of EP monitoring is limited to intermittent analysis by a highly trained clinical neurophysiologist, the authors believe in changing this paradigm by developing continuous monitoring systems, such as the INM system, capable of automated quantitative EP analysis. This noninvasive monitoring modality will allow for a wider range of use in clinical practice. Based on volunteer and clinical patient studies, the INM monitoring system demonstrates much greater reliability and accuracy via the artifact rejection and denoising strategies. It provides more strategic filtering options for different situations under which the clinical SEP response signal could be greatly contaminated and distorted. Furthermore, the INM system offers a promising approach to signal extraction in real-time monitoring during SEP research.     

The first experiments on electrical safety.

This paper discusses the experiments conducted by physicist and physician Arsenne d'Arsonval on the effect of sinusoidal ac on the body, well before the era of electronics. d'Arsonval's first experiments were on the effect of ac on muscle contraction using frog muscle. He contrived a most ingenious device, which displayed the voltage curve and the force of muscle contraction on a smoked-drum kymograph. By using this instrument, along with various alternators such as the Gramme machine, d'Arsonval was able to show that the muscular contraction force decreased with increasing frequency of the electric current. d'Arsonval then turned his attention to the effect of high-frequency ac on the human body. To this end, he created a spark-gap generator of the type described by Hertz in 1888. d'Arsonval demonstrated two important facts: 1) muscle contraction force decreased with increasing frequency of the current and 2) substantial current could be passed through the body and it produced a sensation of warmth. This he proved with conductive and capacitive coupling. By his experiments, d'Arsonval laid the foundation for two new medical techniques: 1) electrosurgery and 2) diathermy. Today both fields are well established in medicine     

Effects of solid retention time on the performance of submerged anoxic/oxic membrane bioreactor.

In this study, four similar bench-scale submerged Anoxic/Oxic Membrane Bioreactors (MBR) were used simultaneously to investigate the effects of solids retention time (SRT) on organic and nitrogen removal in MBR for treating domestic wastewater. COD removal efficiencies in all reactors were consistently above 94% under steady state conditions. Complete conversion of NH(4+)-N to NO(3-)-N was readily achieved over a feed NH(4+)-N concentration range of 30 to 50 mg/L. It was also observed that SRT did not significantly affect the nitrification in the MBR systems investigated. The average denitrification efficiencies for the 3, 5, 10 and 20 days SRT operations were 43.9, 32.6, 47.5 and 66.5%, respectively. In general, the average effluent nitrogen concentrations, which were mainly nitrate, were about 22.2, 27.6, 21.7 and 13.9 mg/L for the 3, 5, 10 and 20 days SRT systems, respectively. The rate of membrane fouling at 3 days SRT operation was more rapid than that observed at 5 days SRT. No fouling was noted in the 10 days and 20 days SRT systems during the entire period of study.