Perspective channel-type reactor with enhanced safety

Following the search for new design solutions to develop within the framework of channel trends the reactor with enhanced safety the Research and Development Institute of Power Engineering has developed the design of the multiloop boiling water reactor (MKER). The MKER enhanced safety is attained when involving the inherent safety features, passive safety systems as well as the accident consequences confinement devices. The design realizes several advantages which are typical of the channel-type reactors, namely: the design desintegration simplifying the manufacture, control, equipment delivery and decreasing, versus the pressure vessel reactors, the accident effect if it proceeds in an explosive manner; small operating reactivity margin and fuel burnup increased due to continuous refuelling; fuel cycle flexibility allowing comparatively easily to adopt the reactor to the conjuncture of the country fuel balance; multiloop circuit of the main coolant which reduces the degree and effect of the accidents connected with the equipment and pipings rupture; monitoring of the channels and fuel assemblies leak-tightness.     

Crack growth measurements on components under cyclic loading: comparison of different methods

The cyclic crack growth behaviour was measured by means of d.c. potential drop, a.c. potential drop, ultrasonic and crack-opening displacement (COD) methods. The methods were applied to component tests on straight pipes with an outer diameter of approximately 800 mm and a wall thickness of approximately 50 mm. The pipes were subjected to constant internal pressure (about 15 MPa) and either an alternating (or pulsating) or a quasi-static bending moment using d.c. potential drop, a.c. potential drop, ultrasonic and flaw-opening (COD) methods. The efficiency of the particular methods has been proved by comparison with fractographical analysis of the fracture surfaces.     

Measurement of interfacial area concentration in subcooled liquid-vapour flow

In two-fluid modelling, accurate prediction of the interfacial transport of mass, momentum and energy is required. Experiments were carried out to obtain a database for the development of interfacial transport models, or correlations, for subcooled water-steam flow in vertical conduits. The experimental data of interest included the interfacial area concentration, interfacial condensation heat transfer and bubble relative velocity. This paper focuses on the interfacial area concentration. The interfacial area concentration was obtained by measuring the distributions of bubble volume and surface area as well as the area-averaged void fraction at various axial locations in subcooled water-steam condensing vertical upward flow under low flow rate and low pressure conditions. The bubble size and surface area were determined using high-speed photography and digital image processing techniques. The area-averaged void fraction was measured by a single-beam gamma densitometer. The results were compared with existing correlations, which were developed on the basis of data obtained for air-water adiabatic flows. Poor agreement between the present data and the existing correlations was obtained. Accordingly, new correlations suitable for subcooled liquid-vapour bubbly flow are proposed.     

Synthesis and characterization of tungsten disulphide films grown by pulsed-laser deposition

The synthesis and characterization of tungsten disulphide (WS₂) films grown on 440C stainless steel substrates using the 248 nm line from a KrF excimer laser are reported. Film properties could be adjusted by controlling substrate temperature and by laser or thermal anneals. X-ray photoelectron spectroscopy, glancing angle XRD, Raman spectroscopy and high-resolution scanning electron microscopy were used to evaluate film chemistry, crystallinity and morphology. Films grown at room temperature were amorphous, near stoichiometric, and had a multiplicity of chemical states. Local order and bonding were improved most dramatically through post-deposition laser anneals. Crystallite size could be increased by raising the substrate temperature during deposition and, to a lesser degree, by post-deposition thermal anneals. Local disorder was observed within the larger crystallites compared to those that were laser annealed. Crystallinity was induced in amorphous films by mechanical rubbing at room temperature under conditions where frictional heating was negligible. The degree of control over film properties provided by PLD demonstrates its value for growing/designing tribological coatings.     

A forward-looking system for planning and monitoring metrological support to an organization

The ARM-Uchet computerized system is considered, which is intended for accounting, planning, and monitoring for metrological support to an organization and has been implemented on an IBM PC AT. Schemes are given for the basic modes of operation and for the software suites, as well as the database structure.Translated from Izmeritel'naya Tekhnika, No. 7, pp. 70–71, July, 1994.     

EFFECT OF THE RATIO Th/U ON TL DATING ACCURACY

ＥＦＦＥＣＴＯＦＴＨＥＲＡＴＩＯＴｈ／ＵＯＮＴＬＤＡＴＩＮＧＡＣＣＵＲＡＣＹ￥Ｐ．Ｌ．Ｌｅｕｎｇ（梁宝鎏）；ＭｉｃｈａｅｌＪ．Ｓｔｏｋｅｓ（ＤｅｐａｒｔｍｅｎｔｏｆＰｈｙｓｉｃｓａｎｄＭａｔｅｒｉａｌｓＳｃｉｅｎｃｅ，ＣｉｔｙＰｏｌｙｔｅｃｈｎｉｃｏ...     

Simultaneous solution of emission transfer and thermal conductivityequations in the problems of atmosphere and subsurface radiothermometry

Expressions are derived that relate the half-space temperature profile and the heat flux with the brightness temperature evolution. Remote sensing methods are proposed to measure the temperature and heat flux in the atmosphere and subsoil layer by radiometric measurements     

Controlling for stimulus dominance in dichotic listening tests: A modification of !l.

Dichotic listening procedures have been used to assess cerebral lateralization in normal Ss. One particularly useful technique is the use of stimuli that fuse into a single percept. Although this procedure has many advantages over other dichotic listening methods, it is particularly susceptible to stimulus dominance, which acts as noise in a S's response data, thus reducing the power of any statistical test of the ear advantage. It is proposed that the solution to this problem is a log-linear analysis of the response data to yield a λ-type index (λ*) that is a measure of ear dominance independent of stimulus dominance. Details of the analysis are provided, as well as a sample analysis of data collected from 104 right-handed and 30 left-handed Ss. Comparisons are drawn between the log-linear analysis and other methods that have been proposed to control for stimulus dominance in this single-response dichotic fusion procedure. (PsycINFO Database Record (c) 2010 APA, all rights reserved)     

A boost-type converter for DC-supply of fluorescent lamps

A boost type converter is described that is suitable for low-voltage DC-supply of fluorescent lamps. It has inherent lamp current limitation (ballast action) and provides the high voltage pulses and electrode heating that are required for igniting the lamp. The proposed circuit is applicable in automotive, emergency, and portable light sources.<>     

A novel scheme for protection of power semiconductor devicesagainst short circuit faults

Power semiconductor devices find wide application in modern power electronic converters. Protection of these devices against overload/short circuit conditions is of paramount importance. Present day protection topologies employing different circuits have invariably one main drawback in that the fault current reaches the set value before action is initiated to trip the system. This poses a severe stress on the device. Hence an adequate safety margin has to be necessarily provided to prevent excessive device stresses and care has to be taken to see that the device is operated well within its safe operating areas. The present paper proposes a method wherein the slope or rate of rise of the fault current is detected and once the slope exceeds the set reference, action is initiated to trip the system much before the fault current reaches dangerous levels. The method provides a fast means of detection of overload and short circuit currents and can be conveniently adopted for the protection of devices in power transistor/IGBT based inverters against short circuited load conditions or shoot through faults. The possible reduction of stresses in the power devices are also highlighted